Clips
Rotor Clip TY. Stainless Steel hardness HR15N 82.5-86
You may also be interested in
Washers Lock
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Circlips
N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).
Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips. This category may be available in the new MBA online store at
Circlips - External - Inverted.
Related Information:
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
Related Information:
Imperial and metric DIN471 / D1400 / N1400 / D1460. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
Related Information:
Clips
M1465 / DTX / Seeger ZA and KS.
Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested. This category may be available in the new MBA online store at
Push On Retaining Rings - Carbon Steel.
Washers Lock
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches. Washers designed to be used to help prevent nuts from vibrating loose. This category may be available in the new MBA online store at
Washers - Lock - Internal Tooth - Spring Steel.
Pins Clevis
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
In addition to retaining parts on a shaft or axle, clevis pins can also be used as light duty axles, spring holders or even fishing line weights. This category may be available in the new MBA online store at
Pins - Clevis - Stainless Steel 316 - Pin Locking.
Related Information:
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
Related Information:
Match with a suitable E-Clip or Circlip to suit groove size shown in listings
In addition to retaining parts on a shaft or axle, clevis pins can also be used as light duty axles, spring holders or even fishing line weights. Grooved end to suit retaining clip instead of pin. This category may be available in the new MBA online store at
Pins - Clevis - Stainless Steel 300 Grade - Groove Locking.
Related Information:
Includes series M3200 / SP / ESP / M2400 / SW snaprings. Similar to a circlip without the lugs.
301 S11/S22 Stainless Steel. Used on the outside diameter of a bearing, shaft or similar equipment. This category may be available in the new MBA online store at
Snap Rings - External - Stainless Steel.
Includes series CI / VH / UR - Stainless Steel.
Light duty rings for use in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CI, Smalley: VH, Spirolox and Ramsey: UR.
Stainless Steel Bearings with a Snap Ring on the OD
Single row radial ball bearings with extended inner ring (wide inner ring). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at
Bearings - Ball - WIR - 440C Stainless.
Related Information:
Includes series CE / VS / US - Stainless Steel.
Light duty single turn rings used in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CE, Smalley: VS, Spirolox and Ramsey: US.
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Related Information:
316 stainless steel wire rings.
Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Related Information:
Unthreaded.
Compression shear mounts for harsh environments.
Excellent protection against shock vibration and noise4 in compression and shear applications. Developed especially for applications in harsh environments in food and pharmaceutical industries. High dampening characteristics. Stainless top plate is domed to guard against oil contamination. Low profile. Compact design. Elastomer insert is made from highly chemical resistant nitrile with good deflection properties. Concentric rings in the base of the insert firmly anchor machine to the floor.
Related Information:
AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2. This category may be available in the new MBA online store at
Spiral Rings - External - Heavy Duty - Stainless Steel.
AE / WS / AS3218 / RS / MIL-R-27426A1 - Stainless Steel.
Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AE, Smalley: WS, Spirolox and Ramsey: RS, Aerospace AS3218, MIL-R-27426A1. This category may be available in the new MBA online store at
Spiral Rings - External - Medium Duty - Stainless Steel.
Includes AI / WH / AS3217 / RR / MIL-R-27426B1 - Stainless Steel.
Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AI, Smalley: WH, Spirolox and Ramsey: RR, Aerospace AS3217, MIL-R-27426B1. This category may be available in the new MBA online store at
Spiral Rings - Internal - Medium Duty - Stainless Steel.
AME / WST / RST - Stainless Steel.
Originally designed to fit NAS50-51 grooves, this series is a popular OEM specification. This two/three turn design is easier to install than the heavy duty RRN option. Equivalent to Associated Spring: AME, Smalley: WST, Spirolox and Ramsey: RST. This category may be available in the new MBA online store at
Spiral Rings - External - Medium-Heavy Duty - Stainless Steel.
Includes AHI / WHM / AS3215 / Spirolox RRN / MIL-R-27426B2 - Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHI, Smalley: WHM, Spirolox and Ramsey: RRN, Aerospace AS3215, MIL-R-27426B2. This category may be available in the new MBA online store at
Spiral Rings - Internal - Heavy Duty - Stainless Steel.
Includes Series AMI / WHT / Spirolox RRT - Stainless Steel.
Originally designed to fit NAS50-51 grooves, this series is a popular OEM specification. This two/three turn design is easier to install than the heavy duty RRN option. Equivalent to Associated Spring: AMI, Smalley: WHT, Spirolox and Ramsey: RRT. This category may be available in the new MBA online store at
Spiral Rings - Internal - Medium-Heavy Duty - Stainless Steel.
Self locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Also known as a lynch pin.
Pin is made from carbon steel and heat treated to RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated. This category may be available in the new MBA online store at
Pins - Clik - Stainless Steel 316 Grade.
Related Information:
Unthreaded
Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.
17-4 PH or PH15-7MO stainless steel spindle and shank. Handles aluminium unless noted otherwise.
Positive lock detent pins. Aluminium handles. 300 Grade Stainless Components. 440C Stainless Balls. Ring dimensions may vary. Please contact us before purchasing if the ring dimensions are important to your application.
Related Information:
17-4 PH or PH15-7MO stainless steel spindle and shank. Self locking and positive locking. All components made from stainless steel.
Related Information:
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at
Bearings - Thrust - Ball - Grooved - Stainless Steel.
Related Information:
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at
Bearings - Thrust - Ball - Flat - Stainless Steel.
Related Information:
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100
oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at
Bearings - Linear - Ball - Stainless Steel - Closed.
Related Information:
Quick release. Body and spindle 17-4 PH stainless steel. Ring and spring 17-7 MO stainless steel. Handle and collar are 300 grade stainless. Tee handle.
Related Information:
Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.
This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring. This category may be available in the new MBA online store at
Springs - Drawbar - Stainless Steel.
Related Information:
Self Locking - Quick Release.
Related Information:
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Related Information:
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
Related Information:
Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Related Information:
301 Stainless Steel
Mounting hole specifications will be supplied on request. These springs are usually mounted on a drum and the free end attached to a loading force like a counterbalance. Free ID may vary to meet load specification. Load capacity can be increased by using multiple strips in tandem, back to back or laminated. Be sure to leave at least 40mm coiled on the drum at full extension. The spring ID will wrap tightly on the drum so that most applications require no fastening to the drum. This category may be available in the new MBA online store at
Springs - Constant Force.
Related Information:
Fast economical installation.
Fits frames from 1.1 to 7.1mm thick. Installation hole size 15mm x 39.9mm. Push to close and pull to open. Spring loaded over centre action. Corrosion resistant black ABS with 303 stainless steel spring.
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at
Bearings - Ball - Flanged - WIR - 440C Stainless.
Related Information:
304 Stainless Steel
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240
oC to 190
oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000. This category may be available in the new MBA online store at
Bearings - Linear - Sliding - Stainless - PTFE - Closed.
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240
oC to 190
oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000. This category may be available in the new MBA online store at
Bearings - Linear - Sliding - Stainless - PTFE - Open.
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings with extended inner ring (wide inner ring). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at
Bearings - Ball - WIR - High Precision - 440C Stainless.
Related Information:
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Related Information:
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.