Small Parts & Bearings - an MBA company

Washers Flat Hardened Steel Categories


Washers Flat Metallic


Washers - Flat - Hardened Steel
Washers - Flat - Hardened Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.


Related Information:




Washers - C - Swing
Washers - C - Swing


Cold finished steel, hardened and ground. Black oxide finish.



Washers - C - Steel
Washers - C - Steel

Also see combined categories:
All C Washers

Cold finished steel, case hardened with a black oxide finish.



Washers - Heavy Duty - Machined - Steel
Washers - Heavy Duty - Machined - Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

Case hardened cold finished steel with black oxide finish.


Related Information:


You may also be interested in

Washers Aligning


Washers - Self Aligning - Components - Hardened Steel
Washers - Self Aligning - Components - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.

Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.


Washers - Self Aligning - Sets - Hardened Steel
Washers - Self Aligning - Sets - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.


Washers Locking


Washers - Serrated - Safety
Washers - Serrated - Safety

Also see combined categories:
All Serrated Locking Washers

Spring Steel Hardened Black.



Bearings Thrust


Bearings - Thrust - Ball - Washers Only - Chrome Steel
Bearings - Thrust - Ball - Washers Only - Chrome Steel

Also see combined categories:
All Ball Thrust Bearing Components

Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.

Carbon Steel Washers are hardened to RC59.61.

Related Information:


Bearings - Thrust - Ball - Washers Only - Stainless Steel
Bearings - Thrust - Ball - Washers Only - Stainless Steel

Also see combined categories:
All Ball Thrust Bearing Components

Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.

Stainless Steel Washers are hardened to HRC38.42.

Related Information:


Linear Slides


Linear Slides - MiniVee - Track - Hardened Steel
Linear Slides - MiniVee - Track - Hardened Steel


Use with MiniVee carriages and support washers

Low profile miniature linear slide system ideal for semi-conductor, laboratory, medical and packaging applications. Non actuated MiniVee linear slide consists of one or more 6061-T6 anodised aluminium wheel carriages with Dual Vee integrated wheels. Double edged track from 165 to 927mm. Carriages and track sold separately.

Related Information:


Washers - Flat - Mild Steel
Washers - Flat - Mild Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. Includes fender washers. Zinc plated and unplated listings.

In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Related Information:


Washers - Flat - Sintered Bronze - Precision
Washers - Flat - Sintered Bronze - Precision

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat thrust washers made from oil impregnated sintered bronze


Related Information:


Washers - Flat - Stainless Steel 304 - Commercial
Washers - Flat - Stainless Steel 304 - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Related Information:


Washers - Flat - Stainless Steel 316 - Commercial
Washers - Flat - Stainless Steel 316 - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Related Information:




Washers - Flat - Carbon Spring Steel - Precision Shim
Washers - Flat - Carbon Spring Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.

C1010 steel types best suited to arbor shimming.

Related Information:


Washers - C - 303 Stainless Steel
Washers - C - 303 Stainless Steel

Also see combined categories:
All C Washers

Knurled outside edge



Washers - Heavy Duty - Machined - Stainless Steel
Washers - Heavy Duty - Machined - Stainless Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

303 Stainless Steel


Related Information:


Washers - Flat - Fibre
Washers - Flat - Fibre

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat red vulcanised fibre washers. Black available on request and sufficient quantity.

Operating temperature up to 105 oC. Tensile strength 6 kg/mm2. Elongation up to 19 percent. Shrinkage up to 3 percent thickness. Water absorption 4 to 70 percent after 24 hours. Density 1 to 1.45 g/cm.

Related Information:




Washers - Flat - Brass - Commercial
Washers - Flat - Brass - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Related Information:




Washers - Flat - High Tensile
Washers - Flat - High Tensile

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Grade 8 high tensile washers

ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Related Information:


Washers - Flat - Titanium - CP Grade 1
Washers - Flat - Titanium - CP Grade 1

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.

Related Information:


Washers - Flat - Titanium - Ti-Gr5 - Ti-6Al4v
Washers - Flat - Titanium - Ti-Gr5 - Ti-6Al4v

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Used in critical aircraft structural components. UNS R56400. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:


Washers - Flat - Nylon
Washers - Flat - Nylon

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Related Information:










Screws - Thumb - Flat Key Head - Washer Face - Steel
Screws - Thumb - Flat Key Head - Washer Face - Steel

Also see combined categories:
All Thumb Screws

Flat Key head malleable iron screws with an integral washer



Tool Steel - 496 Oil Hardening - Flat Stock
Tool Steel - 496 Oil Hardening - Flat Stock


General purpose tool steel with good wear resistance, durability and machinability

Dimensionally stable chromium, tungsten and vanadium electric furnace toolsteel can be used for intricate work. Low 787 to 815 oC (1450-1500 F) hardening range makes it easy to harden. Fully spheroidised and annealed for uniform carbide size and easy machining. Each piece is individually wrapped and clearly marked with size, analysis and correct hardness and tempering information. Edge squareness 0.003 mm per mm. Finish is 0.0008mm (0.000032 inch).


Pins - Dowel - Extractable - With Vent
Pins - Dowel - Extractable - With Vent

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6 with a ground flat along one edge

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650. Also known as parallel pins.

Related Information:


Spacers - Arbor
Spacers - Arbor


Flat arbor shim washers with keyway groove.



Bumpers - Round - Urethane - Female Washer
Bumpers - Round - Urethane - Female Washer

Also see combined categories:
All Female Bumpers
All Bumpers

With steel core. Washer type has a counterbored hole to accept a socket head cap screw. Flat washer molded inside.



Bearings - Thrust - Ball - Flat - Chrome Steel
Bearings - Thrust - Ball - Flat - Chrome Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:


Bearings - Thrust - Ball - Flat - Stainless Steel
Bearings - Thrust - Ball - Flat - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:


Pins - Dowel - Extractable
Pins - Dowel - Extractable

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6. Din 7979.

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.

Related Information:


Washers - Disc Spring - Plastic
Washers - Disc Spring - Plastic

Also see combined categories:
All Disc Springs

Also known as belleville washers.

Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.


Stops - Spring - Flat Button
Stops - Spring - Flat Button

Also see combined categories:
All Spring Stops

Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.



Stops - Spring - Flat Face
Stops - Spring - Flat Face

Also see combined categories:
All Spring Stops

Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.



Stops - Spring - Flat Face - With Tang
Stops - Spring - Flat Face - With Tang

Also see combined categories:
All Spring Stops

Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.

Tang prevents thin gauge material from sliding under plunger.


Screws - Panel - Jack - Steel
Screws - Panel - Jack - Steel

Also see combined categories:
All Panel Screws

Female 4-40 UNC thread in head allows for secure fixing of studs to a panel.

Each screw comes with two flat washers, 1one lock washer and one hex nut. Yellow chromate zinc finish.


Slides - Linear - Cross Roller Rail
Slides - Linear - Cross Roller Rail

Also see combined categories:
All Linear Slides

Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.

Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds.


Linear Slides - MiniVee - Track - Unhardened Steel
Linear Slides - MiniVee - Track - Unhardened Steel


Use with MiniVee carriages and support washers

Low profile miniature linear slide system ideal for semi-conductor, laboratory, medical and packaging applications. Non actuated MiniVee linear slide consists of one or more 6061-T6 anodised aluminium wheel carriages with Dual Vee integrated wheels. Double edged track from 165 to 927mm. Carriages and track sold separately.

Related Information:


Rollers - Steel
Rollers - Steel

Also see combined categories:
All Rollers

Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings

Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.

Related Information:


Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:


Washers - Cup - Stainless Steel
Washers - Cup - Stainless Steel

Also see combined categories:
All Cup Washers

For countersunk screws.

Stainless Steel cup washers.


Washers - Cup - Steel - Nickel Plated
Washers - Cup - Steel - Nickel Plated

Also see combined categories:
All Cup Washers

Countersunk washers for use with screws for decorative finishing



Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124472 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124472 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.