Covid-19 Update!! Current supply status.
Trading by online order and email.
Outbound Deliveries: Allow a few extra days within Australia and extra 7 days for overseas deliveries.
Pre-orders and Backorders: Allow extra 7 days due to quarantine precautions.
Distributors: Most MBA distributors are open and able to contact us using the distributor phone line.
Tools Screw Extractors Categories
Tools - Screw Extractors
The quick and easy way to remove broken screws, bolts, pipes and studs.
Note! You will also need a drill bit of the correct size for each extractor.
Screws - Security - Socket - Tools
Only available to users of the Socket Type Security Screws. Metric only.
Used for hex socket security screws.
Related Information:
Screws - Security - Post Combi Square - Tools
Metric only.
Used for two hole security screws.
Related Information:
Screws - Shoulder - Jig and Fixture - Steel
Used in construction of tool, jig and fixture work. 4140L heat treated steel with black oxide finish.
Also known as stripper bolts.
Screws - Security - Button - Socket
Metric only.
Use special tool listed under Screws - Security - Socket - Tools..
Related Information:
Screws - Security - Cap - Socket
Metric only.
Use special tool listed under Screws - Security - Socket - Tools..
Related Information:
Tools - Thread Repair
Quickly repairs damaged screws
Twisting the handle opens and closes the floating blade around screw. Rotating the tool around screw quickly repairs damaged threads. Adjustable to suit both metric and imperial threads. Blades automatically adapt to any thread pitch or groove. Can be used on both Left and Right hand threads.
Screws - Security - Socket - Countersunk - Stainless
Metric only.
Use special tool listed under Screws - Security - Socket - Tools..
Related Information:
Screws - Security - Socket - Countersunk - Zinc Plated
Metric only.
Use special tool listed under Screws - Security - Socket - Tools..
Related Information:
Tools - Nut Drivers
Includes socket wrench for 0-80 size screws
Lengths shown are based on standard stock but may vary.
Screws - Security - Post Combi Square - Pan Head - Super Zinc
Each 200 pack comes with a Post Combination Driver Bit. Metric only.
Use special tool listed under Screws - Securty - Socket - Tools.
Related Information:
Inserts - Thread Repair - Recoil Starter Sets
Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
Tools - General
Butane Torch, Inspection Mirror, Mini Sandblaster, Nibbling Tool, Plastic Scriber, Pick Up Tool Set, Hex Driver Handle for Insert Bits
X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more.
Inserts - Thread Repair - Helicoil Tang Breakoff Tools
The driving tangs of helicoil inserts must be removed to prevent interference with the end of the assembled screw. For inserts over 1/2 inch use long nosed pliers.
Tools - Mandrels and Nosepieces - For Klik Rivet Nuts
Required for Thread Setter Tool
Twisting the handle opens and closes the floating blade around screw. Rotating the tool around screw quickly repairs damaged threads. Adjustable to suit both metric and imperial threads. Blades automatically adapt to any thread pitch or groove. Can be used on both Left and Right hand threads.
Related Information:
Balls - Tooling - Two Piece - Construction - Steel
High quality tooling balls provide a precise reference point for critical machining operations.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.
Related Information:
Inserts - Thread Repair - Helicoil
Replacement helicoil inserts for after you have purchased a starter kit or tools separately.
Stainless 18-8 inserts with a hardness of RC43-50 and tensile strength above 200,000 PSI. Metric and Imperial available. Screw locking inserts have a series of straight segments to provide self-locking torque on the bolt, eliminating a need for other threadlocking methods.
Inserts - Self Tapping - For Plastics - Stainless Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Inserts - Self Tapping - For Wood - Slotted Drive
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.
Related Information:
Inserts - Self Tapping - For Plastics - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
Inserts - Self Tapping - For Aluminium - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Inserts - Self Tapping - For Aluminium - Stainless 303
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Inserts - Rivet Nuts - Klik - Threadsert
Individual Inserts for use with the Klik Thread Setter Tool
These threaded inserts can be used in blind or through hole applications. Can be used in almost any material over 2.38mm thick. As the insert is installed the threaded section is completely swaged into the sleeve portion of the hole, permitting them to be used with grade 8 screws. The installation hole size is determined by the density of the parent material. Can be pressed or otherwise compressed manually with a hammer for quick installation jobs in sheet material. Tools are available for assembly in blind holes or production assembly. Email us for a price on tools.
Screws - Roof Bolt - Steel
Metal Thread Screws. Metric and BSW only. Supplied with nut.
Nuts sold seperately - See Nuts.
Related Information:
Screws - Thumb - Flat Key Head - Washer Face - Steel
Flat Key head malleable iron screws with an integral washer
Related Information:
Screws - Thumb - Knurled - Brass
Brass knurled head thumb screws with zinc or black oxide protective coating.
Related Information:
Screws - Thumb - Knurled - Washer Face - Aluminium
Knurled head aluminum thumb screws with an integral washer
Related Information:
Screws - Thumb - Knurled - Washer Face - Brass
Knurled head brass thumb screws with an integral washer
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 126906 products in 2519 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
