Shafting Ground Precision Stainless 440c Grade Hardened Categories
Shafting Precision Ground
Shafting - Ground - Precision - Stainless 440C Grade Hardened
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
Related Information:
Shafting - Ground - Precision - Stainless 416 Grade Hardened
Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.
Related Information:
Shafting - Ground - Precision - Stainless 420 Grade Hardened
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
Related Information:
You may also be interested in
Linear Bearings
Bearings - Linear - Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.
Related Information:
Shafting Precision Ground
Shafting - Pre Drilled and Tapped - Stainless Steel Steel
For use with rail supports and open linear bearings
Shafting - Ground - Precision - High Carbon Steel
Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.
Related Information:
Shafting - Ground - Precision - Chrome Plated
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance.
Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1
CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance.
Related Information:
Shafting - Ground - Precision - Titanium - Ti-Gr5 - TC4
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Related Information:
Couplings Rigid
Couplings - Rigid - 1 Piece Clamp - Stainless Steel
303 Grade Stainless
Precision Machined. High torsional load. Non marring, easy to install and adjust. Use on hardened shafts, rigid clamp type design, easily machinable. Available with stepped bores and keyways on 5 week delivery.
Shafting General Purpose
Shafting - Unground - Silver Steel
Unhardened silversteel shafting for general purposes. Not suitable for precision bearings until machined to correct tolerances and hardened.
See also drill rod. Drill Rod.
Related Information:
Shafting Precision Ground
Shafts - Idler
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design.
Related Information:
Rail Supports - Without Shaft
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium.
Related Information:
Rail Supports - With Shaft
Includes linear shafting.
Includes shaft to h6 tolerances. Support is made from aluminium.
Related Information:
Supports - Pedestal Two Bolt
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
Related Information:
Shafting - Pre Drilled and Tapped - High Carbon Steel
For use with rail supports and open linear bearings
Straightness: 0.1 mm / mtr.
Rail Supports - With Shaft - One Piece
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.
Related Information:
Collars
Collars - Shaft - Hinged - Stainless Steel
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Pins - Dowel - Standard - 316 Stainless - Chamfered End
Precision Dowel Pins - 316 Grade - DIN6325, ISO2338
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 416 Stainless - Chamfered End
Precision Dowel Pins - 416 Grade - DIN6325, ISO2338
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Shim and Foil - Stainless Steel
Precision stainless shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
Related Information:
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Precision Dowel Pins - 316 Grade - DIN7
Diameter tolerances are m6. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 303-304 Stainless - Chamfered End
Precision Dowel Pins - 303/304 Grade Stainless - DIN6325, ISO2338
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends
Precision Dowel Pins - 303/304 Grade Stainless- DIN7
Rounded end dowel pins are measured from the start of the edge rounding. This allows the pin to completely fill the hole after you grind off the rounded end. Diameter tolerances are m6. Also known as parallel pins.
Related Information:
Washers - Flat - Stainless Steel 304 - Commercial
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
Related Information:
Washers - Flat - Stainless Steel 316 - Commercial
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
Related Information:
Shafting - Carbon Steel - Keyed
Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.
Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Rod - Drill Blanks
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.
Rail Systems - Type 1 - Linear - Precision - Rails
Match with carriages by Size Column
Profile rail guides are used in the production of linear guidance systems with unlimited travel. They consist of a profile rail with 4 precision ground raceways and a slide usint with four ball circulation paths. The square configuration of the raceways results in a guidance system with good rigidity, capable of withstanding moment loads in all directions. The load carrying capacity is equal in all four directions. Low vibration and low noise. Case hardened steel. Supplied with a light preload. Lubricated with lithium based grease.
Related Information:
Rail Systems - Type 1 - Linear - Precision - Carriages - Flanged
Match with rails by Size Column. With Lube Reservoir
Profile rail guides are used in the production of linear guidance systems with unlimited travel. They consist of a profile rail with 4 precision ground raceways and a slide usint with four ball circulation paths. The square configuration of the raceways results in a guidance system with good rigidity, capable of withstanding moment loads in all directions. The load carrying capacity is equal in all four directions. Low vibration and low noise. Case hardened steel. Supplied with a light preload. Lubricated with lithium based grease.
Related Information:
Rail Systems - Type 1 - Linear - Precision - Carriages - Narrow
Match with rails by Size Column. With Lube Reservoir
Profile rail guides are used in the production of linear guidance systems with unlimited travel. They consist of a profile rail with 4 precision ground raceways and a slide usint with four ball circulation paths. The square configuration of the raceways results in a guidance system with good rigidity, capable of withstanding moment loads in all directions. The load carrying capacity is equal in all four directions. Low vibration and low noise. Case hardened steel. Supplied with a light preload. Lubricated with lithium based grease.
Related Information:
Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel
Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.
Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.
Tube - Round - Stainless Steel
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
Related Information:
Bearings - Ball - High Precision - 440C Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Bearings - Ball - Flanged - High Precision - 440C Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Bearings - Ball - WIR - High Precision - 440C Stainless
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings with extended inner ring (wide inner ring). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Knobs - Precision - Knurled
Set screw and clamp types - Stainless Steel. Also known as Thumb Knobs.
303 Stainless Steel. ID Tolerance +0.013 / -0.000 mm (+0.0005 / - 0.0000 inch).
Clamps - Gear - Split
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Shims - Slotted - Imperial Sizes
Precision stainless steel 300 series. Solves alignment and leveling problems on pumps, generators and other machinery. Tabs eliminate need to place hands under machinery. Conform to standard bolt and stud sizes.
Ball Transfer Units - Screw Stem - Stainless - Precision
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
Collars - Shaft - Standard - Stainless Steel
Includes miniature precision types. 303 and 316 Types.
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft.
Related Information:
Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Joints - Swivel - Knob Style - Stainless Steel
Precision made. Column lock feature. Will not become loose when adjusting. Universal design will fit any make of magnetic base, surface gauge or indicator. 303 Stainless Steel.
Main Pages
About Us
Balls
Bearings
Brands
Catalogue
Clearance Items
Contact Us
Dental Bearings
Frequently Asked Questions
Freight Rates and Shipping Times
Games Clearance
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Ordering
Payment and Shipping
Dowel Pins
Privacy
Product Showcase
Google Search
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 124370 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
