Screws Pan Head
UNC metal thread machine screws
Related Information:
You may also be interested in
Screws Thumb
Knurled head aluminum thumb screws with an integral washer
Related Information:
Screws Cap Head
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN912. This category may be available in the new MBA online store at
Screws - Cap - Socket - Aluminium.
Related Information:
Housings for Ball Bearings
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
Pins Dowel
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Washers Finishing
For countersunk screws.
Thread Inserts
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
Ball Transfers
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at
Ball Transfer Units - Screw Stem - Brass and Aluminium.
Couplings Helical and Slit
Related Information:
Clamps
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Couplings Helical and Slit
Aluminium - Flexible.
Couplings Rigid
0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000. This category may be available in the new MBA online store at
Couplings - Rigid - Set Screw.
Related Information:
Pins Pull
Spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations.
Two part assembly includes a barrel and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. 3/8-16 Threaded end so you can add your own handle or knob. Aluminium housing 6061-T6, Steel pin 12L15. Pull up force approx 2.2kg.
Related Information:
Screws Pan Head
Metal Thread Screws. Metric only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at
Screws - Pan Head - Titanium CP Grade 1 - Philips Drive.
Related Information:
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Related Information:
Metric Only
Related Information:
Metric Only
Related Information:
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Related Information:
Metric Only
Related Information:
Brass metal thread machine screws METRIC
Related Information:
UNC - UNF - Metric
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
Related Information:
Machine screws. PEEK is a super-engineering thermoplastic with special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of VitreTM.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180o Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
Related Information:
Metal Thread Screws UNC - UNF - METRIC
Related Information:
Metal Thread Screws. Metric only.
Related Information:
Metal Thread Screws. Metric only.
Related Information:
Screws Self Tapping
Zinc chromate fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.
Type AB Steel Self Tapping Screws.
Type AB Steel Self Tapping Screws.
Type AB Steel Self Tapping Screws.
Type AB Steel Self Tapping Screws.
Screws Pan Head
UNC - UNF - Metric
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
Related Information:
UNC and UNF
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
Related Information:
Screws Security
Each 200 pack comes with a Post Combination Driver Bit. Metric only.
Related Information:
Pulleys Timing AT10 10mm
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Screws Self Tapping
Tri-Lobe Course Thread Plastic Threading Screws
Tri-Lobe Course Thread Plastic Threading Screws
Pins Pull
Spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations.
Two part assembly includes a barrel and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. Handles are black plastic. Aluminium housing 6061-T6, Steel pin 12L15. Pull up force approx 2.2kg. Lockout style (indicated in tables) allows you to pull and rotate handle 1/4 turn to lock plunger in retracted position.
Related Information:
Spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations.
Two part assembly includes a barrel and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. Handles are black plastic. Aluminium housing 6061-T6, Steel pin 12L15. Pull up force approx 2.2kg. Lockout style (indicated in tables) allows you to pull and rotate handle 1/4 turn to lock plunger in retracted position.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel. This category may be available in the new MBA online store at
Supports - Pedestal Two Bolt.
Related Information:
Extra large head. One piece construction. 303 Stainless Steel.
Extra large head. One piece construction. Carbon steel with black oxide finish.
Timing Pulleys to suit GT 5.000mm Pitch Timing Belts. Suits belts 15mm wide. Aluminium, steel and cast iron. Use with GT2 or GT3 type belts.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.