Pins Side Thrust Single Sided Stainless Ball Categories
Pins General
Pins - Side Thrust - Single Sided - Stainless Ball
For holding, clamping and positioning work pieces. Body is black oxide steel.
Stainless ball and stainless spring with black oxide coated steel body. This category may be available in the new MBA online store at Pins - Side Thrust - Single Sided - Stainless Ball.
Related Information:
Pins - Side Thrust - Single Sided - Plastic Ball
For holding, clamping and positioning work pieces. Body is black oxide steel.
Plastic ball and stainless spring with black oxide coated steel body. This category may be available in the new MBA online store at Pins - Side Thrust - Single Sided - Plastic Ball.
Related Information:
Pins - Side Thrust - Single Sided - Steel Ball
For holding, clamping and positioning work pieces. Body is black oxide steel.
Steel ball and elasticised spring with black oxide coated steel body. This category may be available in the new MBA online store at Pins - Side Thrust - Single Sided - Steel Ball.
Related Information:
Pins - Side Thrust - Double Sided - Steel Ball
For holding, clamping and positioning work pieces. Body is black oxide steel.
Steel ball and elasticised spring with black oxide coated steel body. This category may be available in the new MBA online store at Pins - Side Thrust - Double Sided - Steel Ball.
Related Information:
Belts - Metric Timing - 3.000mm Pitch GT - 6mm Wide - Single Sided
GT2 and GT3 Series Metric Timing Belts.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 3.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch HTD - 15mm Wide - Single Sided
HTD Series Metric Timing Belts.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.08mm. Belt Height (W) - 3.81mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch HTD - 9mm Wide - Single Sided
HTD Series Metric Timing Belts.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.08mm. Belt Height (W) - 3.81mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Inch Timing - 2.032mm Pitch MXL - 6.4mm Wide - Single Sided
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Belts - Inch Timing - 5.080mm Pitch XL - 6.4mm Wide - Single Sided
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Belts - Inch Timing - 5.080mm Pitch XL - 9.5mm Wide - Single Sided
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Clamps - Timing Belt
Used for locking the ends of timing belt lengths used in reciprocating applications
Suits single and double sided belts. Black Polycarbonate with 303 stainless fasteners. Low inertia. Compact Design. Patent Pending. For MXL, XL, GT 2mm, GT 3mm, GT 5mm, HTD 3mm and HTD 5mm belt pitches.
Related Information:
Clamp Kits - Timing Belt
Used for locking the ends of timing belt lengths used in linear applications
Suits single sided belts only. Aluminium. Screws, hex nuts and washers included. This category may be available in the new MBA online store at Clamp Kits - Timing Belt.
Related Information:
Spiral Rings - External - Light Duty - Carbon Steel
Includes series CE / VS / US - Spring Steel
Light duty single turn rings used in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CE, Smalley: VS, Spirolox and Ramsey: US.
Spiral Rings - External - Light Duty - Stainless Steel
Includes series CE / VS / US - Stainless Steel.
Light duty single turn rings used in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CE, Smalley: VS, Spirolox and Ramsey: US.
Pins - Wire Lock Lynch - Single Wire - Round - Carbon Steel
Also known as snapper pins
This category may be available in the new MBA online store at Pins - Wire Lock Lynch - Single Wire - Round - Carbon Steel.
Related Information:
Pins - Wire Lock Lynch - Single Wire - Square - Carbon Steel
Also known as snapper pins
This category may be available in the new MBA online store at Pins - Wire Lock Lynch - Single Wire - Square - Carbon Steel.
Related Information:
Pins - Wire Lock Lynch - Single Wire - Trapezoid - Carbon Steel
Also known as snapper pins
This category may be available in the new MBA online store at Pins - Wire Lock Lynch - Single Wire - Trapezoid - Carbon Steel.
Related Information:
Belts - Metric Timing - 3.000mm Pitch GT - 6mm Wide - Double Sided
GT2 and GT3 Series Metric Timing Belts Double Sided
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.22mm. Belt Height (W) - 3.20mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 3.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch HTD - 15mm Wide - Double Sided
HTD Series Metric Timing Belts Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.08mm. Belt Height (W) - 5.30mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch HTD - 9mm Wide - Double Sided
HTD Series Metric Timing Belts Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.08mm. Belt Height (W) - 5.30mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Inch Timing - 9.525mm Pitch L - 12.7mm Wide - Double Sided
Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Pitch (P) - 9.525mm (0.200 inch).
Related Information:
Belts - Inch Timing - 9.525mm Pitch L - 19.1mm Wide - Double Sided
Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Pitch (P) - 9.525mm (0.200 inch).
Related Information:
Belts - Inch Timing - 9.525mm Pitch L - 25.4mm Wide - Double Sided
Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Pitch (P) - 9.525mm (0.200 inch).
Related Information:
Belts - Inch Timing - 2.032mm Pitch MXL - 6.4mm Wide - Double Sided
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.51mm. Belt Height (W) - 1.52mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Belts - Inch Timing - 5.080mm Pitch XL - 6.4mm Wide - Double Sided
Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Belts - Inch Timing - 5.080mm Pitch XL - 9.5mm Wide - Double Sided
Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Bearings - Single Row Ball Unflanged - Standard - Chamfered Edges
Chamfered edge bearings for Linear Guide Systems and pushbikes
Often used in pushbike headsets. Note bearings for pushbikes with two chamfered edges have the chamfer on the inner ring on one side and outer ring on the other - designation CEP.
Related Information:
R Clips - Single Coil - Steel
Also known as internal hitch pins, bridge pins or humpback pins
Material: Spring Wire. This category may be available in the new MBA online store at R Clips - Single Coil - Steel.
R Clips - Single Coil - Stainless Steel
Also known as internal hitch pins, bridge pins or humpback pins
This category may be available in the new MBA online store at R Clips - Single Coil - Stainless Steel.
Pins - Ball Lock - Keyring Style - 300 Grade Stainless Steel - Single Ball
Quick release. Provide positive locking for all types of applications and equipment. Body, head and all internal components are made from corrosion resistant stainless steel.
Positive lock detent pins. 300 Grade Stainless Handles. 300 Grade Stainless Components. 440C Stainless Balls.
Related Information:
Linear Positioner Units
Effective way to position heavy loadsquickly and easily. Single pin unit offers high rigidity with small deflection.
This category may be available in the new MBA online store at Linear Positioner Units.
Bearings - Ball Thrust Grooved - Chrome Steel
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Ball Thrust Grooved - Chrome Steel.
Related Information:
Bearings - Ball Thrust Grooved - Stainless Steel
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Ball Thrust Grooved - Stainless Steel.
Related Information:
Bearings - Ball Thrust Flat - Chrome Steel
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Ball Thrust Flat - Chrome Steel.
Related Information:
Bearings - Ball Thrust Flat - Stainless Steel
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Ball Thrust Flat - Stainless Steel.
Related Information:
Bearings - Ball Thrust Grooved - ZRO2 Ceramic
3 Piece Thrust Bearings Open Type. Excellent performance in electrical and magnetism sensitive applications. Full ceramic silicon nitride.
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Ball Thrust Grooved - ZRO2 Ceramic.
Related Information:
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined. This category may be available in the new MBA online store at Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core.
Related Information:
Washers - Thrust - DP4 Type
Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.
Operating Temperature -200o to 280o Celsius. Maximum load 250N per mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free. This category may be available in the new MBA online store at Washers - Thrust - DP4 Type.
Snap Buttons - Single End - Dog Leg
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating. This category may be available in the new MBA online store at Snap Buttons - Single End - Dog Leg.
Snap Buttons - Single End - Spring Leg
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating. This category may be available in the new MBA online store at Snap Buttons - Single End - Spring Leg.
Collars - Shaft - Hinged - Stainless Steel
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Collars - Shaft - Hinged - Steel
Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
80T Single Speed Penn Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings - Single Row Ball Unflanged - Standard - Ceramic Hybrid
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily. Items with high speed cages have the suffixes T9H, TNH, TW or KC. This category may be available in the new MBA online store at Bearings - Single Row Ball Unflanged - Standard - Ceramic Hybrid.
Related Information:
Bearings - Single Row Ball Unflanged - Standard - Ceramic Si3N4
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02. Full ceramic silicon nitride.
Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Wear and corrosion resistance. Depending on the application, these bearings may run lubrication free or lubricated by the medium in which they are submerged. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 700 deg C without a cage or seals.
Related Information:
Bearings - Single Row Ball Unflanged - Standard - Ceramic ZrO2
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed. Full ceramic zirconia.
Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Depending on the application, these bearings may run lubrication free or lubricated by the medium in which they are submerged. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 1000 deg C without a cage or seals.
Related Information:
Bearings - Single Row Ball Flanged - Extended Inner - 440C Stainless
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
Bearings - Single Row Ball Flanged - Extended Inner - Chrome Steel
Chrome Steel Bearings with Flanges.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
Bearings - Single Row Ball Flanged - Extended Inner High Precision Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Bearings - Single Row Ball Flanged - High Precision Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Single Row Ball Flanged - High Precision Stainless.
Related Information:
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153564 products in 2095 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
