Pins Dowel Standard 303 304 Stainless Chamfered End Categories
Pins Dowel
Pins - Dowel - Standard - 303-304 Stainless - Chamfered End
Precision Dowel Pins - 303/304 Grade Stainless - DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 316 Stainless - Chamfered End
Precision Dowel Pins - 316 Grade - DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 416 Stainless - Chamfered End
Precision Dowel Pins - 416 Grade - DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends
Precision Dowel Pins - 303/304 Grade Stainless- DIN7
Rounded end dowel pins are measured from the start of the edge rounding. This allows the pin to completely fill the hole after you grind off the rounded end. Diameter tolerances are m6. Also known as parallel pins.
Related Information:
Pins - Hammer Drive - Round Head - Stainless Steel
Used to replace screws where the need to remove the pin is unlikely.
Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Precision Dowel Pins - 316 Grade - DIN7
Diameter tolerances are m6. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - Chamfered End
Precision Dowel Pins - DIN6325, ISO2338
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Keysteel Lengths - Rectangular - Stainless Steel
303, 304 and 316 key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.
Related Information:
Keysteel Lengths - Square - Stainless Steel
303, 304 and 316 grade key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.
Related Information:
Pins - Taper - Imperial - Standard - Stainless Steel
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
Related Information:
Collars - Shaft - Standard - Stainless Steel
Includes miniature precision types. 303 and 316 Types.
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft.
Related Information:
Collars - Shaft - Hinged - Stainless Steel
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Socket Set Screws - Cup Point - Standard - 304 Stainless Steel - DIN916
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Studs - Threaded - Standard
Metric and imperial sizes. Steel and 303 stainless steel.
Yield strength 100,000 PSI. Tensile strength 125,000 PSI.
Nuts - Hexagonal - Binx - Stainless Steel 304
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
Pins - Taper - Imperial - Extractable - External Thread - Stainless Steel
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
Threaded externally for easy extraction.
Related Information:
Inserts - Self Tapping - For Plastics - Stainless Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends
Precision Dowel Pins - DIN7
Diameter tolerances are m6. Also known as parallel pins.
Related Information:
Circlips - External - Standard - Stainless Steel
Imperial and metric DIN471 / D1400 / N1400 / D1460. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel.
Related Information:
Circlips - Internal - Standard - Stainless Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request. Standard and heavy duty options.
Related Information:
Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Ball Transfer Units - Flange Mount - Standard - Stainless - Deep
Single ball bearings units for conveyor systems
Ball Transfer Units - Flange Mount - Standard - Stainless - Slim
Single ball bearings units for conveyor systems
Bearings - Linear - Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.
Related Information:
Balls - Stainless Steel - 316L Grade
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
Related Information:
Socket Set Screws - Cup Point - Standard - 316 Stainless Steel - DIN916
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Couplings - Slit Type - Standard
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
Related Information:
Attachments - Thimbles - Stainless Steel
316 Stainless Steel. Use with synchromesh cable or standard miniature cable. Use with synchromesh or standard miniature cable
Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends.
Related Information:
Springs - Compression - Stainless Steel
This category includes short and long lengths
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.
Related Information:
Bearings - Ball - 440C Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless steel radial ball bearings
Standard single row radial ball bearings. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
Sprockets - 6.35 x 2.8mm - Simplex - Stainless Steel - Plain Bore
25-1 ASA 1/4 Inch. Stainless Steel 303 grade with unfinished bore.
Match with 6.35mm simplex chain. American Standard 25-1 - 1/4 inch. For easy ready selected sets of chain and sprockets please see the HES website.
Related Information:
Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Bearings - Acetal with Stainless Balls - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Pins - Hammer Drive - Flat Head
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Slides - Linear - Recirculating Ball - Standard
The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.
Slides - Linear - Non Recirculating Ball - Standard
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
Bearings - Ball - 316 Stainless Steel - Double Row - Open
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.
Related Information:
Bearings - Ball - 316 Stainless Steel - Single Row - Open
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.
Related Information:
Shims - Slotted - Imperial Sizes
Precision stainless steel 300 series. Solves alignment and leveling problems on pumps, generators and other machinery. Tabs eliminate need to place hands under machinery. Conform to standard bolt and stud sizes.
Pins - Clevis - Stainless Steel 304
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
Related Information:
Pins - Roll - Stainless Steel - 300 Grade
304 grade DIN1481.
Also known as sel-lok and bissell pins.
Related Information:
Screws - Cap - Socket - 303 - 304 Stainless
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
Related Information:
Threaded Rod - Allthread - Stainless Steel - 304
UNC - UNF - METRIC - 303 and 304 grades. Also known as booker rod.
Springs - Drawbar - Stainless Steel
Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.
This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring.
Related Information:
Pins - Wire Lock Lynch - Double Wire - Round - 304 Stainless Steel
Also known as snapper pins
Related Information:
Pins - Wire Lock Lynch - Double Wire - Square - 304 Stainless Steel
Also known as snapper pins
Related Information:
Bearings - Ball - 316 Stainless Steel - Single Row - Sealed
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 126923 products in 2399 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
