Worm Gears 48dp Series 1 Metallic Categories
Gears Inch Worms
Worm Gears - 48DP Series 1 - Metallic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 3.35o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. This category may be available in the new MBA online store at Worm Gears - 48DP Series 1 - Metallic.
Related Information:
Worm Gears - 32DP Series 1 - Metallic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. This category may be available in the new MBA online store at Worm Gears - 32DP Series 1 - Metallic.
Related Information:
Worms - 24DP Series 1 - Metallic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. This category may be available in the new MBA online store at Worms - 24DP Series 1 - Metallic.
Related Information:
You may also be interested in
Gears Metric Worms
Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - 24DP Series 1 - Plastic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. This category may be available in the new MBA online store at Worm Gears - 24DP Series 1 - Plastic.
Related Information:
Worm Gears - 32DP Series 1 - Plastic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. This category may be available in the new MBA online store at Worm Gears - 32DP Series 1 - Plastic.
Related Information:
Gears - Spur - 48DP - 20 Degree - Stainless
PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 48DP - 20 Degree - Stainless.
Gears - Spur - 48DP - 20 Degree - Aluminium
PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. 2024 and 5052 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 48DP - 20 Degree - Aluminium.
Gears - Spur - 48DP - 20 Degree - Plastic - Standard
PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. Acetal and nylon. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 48DP - 20 Degree - Plastic - Standard.
Gears - Spur - 48DP - 20 Degree - Plastic with Insert
PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. Acetal and Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 48DP - 20 Degree - Plastic with Insert.
Gear Racks - 48DP - 14.5 PA - Plastic
14.5 Degree Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gear Racks - 48DP - 14.5 PA - Plastic.
Gear Racks - 48DP - Stainless - Standard - Standard
20 Degree Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gear Racks - 48DP - Stainless - Standard - Standard.
Gearboxes - Cross Axis - 110 x 95 x 38mm
Worm and Wormwheel box. 10.3 to 40.0Nm. 5:1 to 120:1 ratios. P45 and PF45 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Related Information:
Gearboxes - Cross Axis - 90 x 75 x 32mm
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Related Information:
Balls - Metallic - Chrome Steel
Hardness: Rockwell C: 60-70.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833. This category may be available in the new MBA online store at Balls - Metallic - Chrome Steel.
Related Information:
Balls - Metallic - Magnetic
Please note that ball magnets are not to be used as toys. These are a strong magnet must be kept away from children as serious harm may result from ingestion.
This category may be available in the new MBA online store at Balls - Metallic - Magnetic.
Balls - Metallic - Phosphor Bronze
Specific Gravity 8.4
Grades shown are AFBMA / ISO3290-1. This category may be available in the new MBA online store at Balls - Metallic - Phosphor Bronze.
Related Information:
Balls - Metallic - Stainless Steel - 304 Grade
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 oC. This category may be available in the new MBA online store at Balls - Metallic - Stainless Steel - 304 Grade.
Related Information:
Balls - Metallic - Stainless Steel - 316 Grade
A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 oC. This category may be available in the new MBA online store at Balls - Metallic - Stainless Steel - 316 Grade.
Related Information:
Balls - Metallic - Stainless Steel - 316L Grade
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. This category may be available in the new MBA online store at Balls - Metallic - Stainless Steel - 316L Grade.
Related Information:
Balls - Metallic - Stainless Steel - 400 Grade
Hardness: Rockwell C: 55-60. Includes 420 and 440C grades
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel. This category may be available in the new MBA online store at Balls - Metallic - Stainless Steel - 400 Grade.
Related Information:
Balls - Metallic - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Standard
Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Related Information:
Balls - Metallic - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded
Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. Threaded either 1-72 UNF or M1.2.
Related Information:
Balls - Metallic - Tungsten Carbide
Extreme hardness and wear resistance.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.
Related Information:
Balls - Bored - Steel
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2. This category may be available in the new MBA online store at Balls - Bored - Steel.
Related Information:
Leadscrew Nuts - Metric - Round - Metallic
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
Related Information:
Leadscrew Nuts - Metric - Square - Metallic
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
Related Information:
Washers - C - Steel
Cold finished steel, case hardened with a black oxide finish.
This category may be available in the new MBA online store at Washers - C - Steel.
Washers - C - Swing
Cold finished steel, hardened and ground. Black oxide finish.
This category may be available in the new MBA online store at Washers - C - Swing.
Washers - Flat - Brass - Commercial
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at Washers - Flat - Brass - Commercial.
Related Information:
Washers - Flat - Hardened Steel
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.
This category may be available in the new MBA online store at Washers - Flat - Hardened Steel.
Related Information:
Washers - Flat - High Tensile
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Grade 8 high tensile washers
ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - High Tensile.
Related Information:
Washers - Flat - Mild Steel
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers. Includes fender washers. Zinc plated and unplated listings.
In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at Washers - Flat - Mild Steel.
Related Information:
Washers - Flat - Aluminium - Precision Shim
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
This category may be available in the new MBA online store at Washers - Flat - Aluminium - Precision Shim.
Related Information:
Washers - Flat - Brass - Precision Shim
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Precision Tolerances. Standard and laminated brass shim washers.
This category may be available in the new MBA online store at Washers - Flat - Brass - Precision Shim.
Related Information:
Washers - Flat - Copper - Precision Shim
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Precision Tolerances.
This category may be available in the new MBA online store at Washers - Flat - Copper - Precision Shim.
Related Information:
Washers - Flat - Sintered Bronze - Precision
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat thrust washers made from oil impregnated sintered bronze
This category may be available in the new MBA online store at Washers - Flat - Sintered Bronze - Precision.
Related Information:
Washers - Heavy Duty - Machined - Steel
Case hardened cold finished steel with black oxide finish.
This category may be available in the new MBA online store at Washers - Heavy Duty - Machined - Steel.
Related Information:
Washers - Flat - Stainless Steel 304 - Commercial
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - Stainless Steel 304 - Commercial.
Related Information:
Washers - Flat - Stainless Steel 316 - Commercial
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - Stainless Steel 316 - Commercial.
Related Information:
Washers - Flat - Stainless Steel - Precision Shim
Precision Tolerances.
This category may be available in the new MBA online store at Washers - Flat - Stainless Steel - Precision Shim.
Related Information:
Washers - Flat - Stamped - Heavy Duty - Hardened
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Heat treated. Black oxide finish.
This category may be available in the new MBA online store at Washers - Flat - Stamped - Heavy Duty - Hardened.
Related Information:
Washers - Flat - Titanium - CP Grade 1
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at Washers - Flat - Titanium - CP Grade 1.
Related Information:
Washers - Heavy Duty - Machined - Stainless Steel
303 Stainless Steel
This category may be available in the new MBA online store at Washers - Heavy Duty - Machined - Stainless Steel.
Related Information:
Washers - Flat - Carbon Spring Steel - Precision Shim
Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.
C1010 steel types best suited to arbor shimming. This category may be available in the new MBA online store at Washers - Flat - Carbon Spring Steel - Precision Shim.
Related Information:
Top Air 100 Series W.H. Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153564 products in 2094 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
