Wear Strips Categories
Wearstrips - Plain
Self-Lube wearstrips provide effective and economical means of controlling and guiding linear motions, especially in large load applications.
Made of solid aluminum bronze. Furnished semi-finished and are able to be cut to size and finished.
Wearstrips - Graphite Plug
Self-Lube wearstrips provide effective and economical means of controlling and guiding linear motions, especially in large load applications.
Made of solid aluminum bronze with self-lubricating graphite plugs. Furnished semi-finished and are able to be cut to size and finished. Plugs are 25.4mm centres. Drill mounting holes either between or through graphite plugs. Before drilling break out graphite.
Strip - Soft Metal Packs
For general hobby applications. This brass strip is annealed soft to make it easier to bend. Brass.
300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.
Strip - Spring Steel
Hundreds of uses.
Hardened and tempered spring steel strip. Note that the width of this strip may vary up to a few mm as it is guillotine cut from strip. If you require a closer tolerance on the strip width please contact us prior to ordering.
Rectangular Bar - Aluminium
Thin and thick Aluminum strip and rectangular profiles
Small sizes may not be perfectly straight.
Balls - Ceramic - Zirconia
Outstanding wear resistance. Excellent thermal and chemical resistance.
Grades shown are AFBMA / ISO3290-1.
Related Information:
Balls - Ceramic - Silicon Nitride
Outstanding wear resistance. Good thermal and chemical resistance.
High hardness. Grades shown are AFBMA / ISO3290-1. High strength over a wide temperature range. High fracture toughness. Outstanding wear resistance. Good thermal and chemical resistance.
Related Information:
Bushes - Steel - DP4 - Split - Flanged
Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.
Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free. Speed Limit in oil 3 metres surface speed per second.
Related Information:
Bushes - Steel - DP4 - Split - Unflanged
Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.
Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free. Speed Limit in oil 3 metres surface speed per second.
Related Information:
Balls - Ceramic - Ruby - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.
Related Information:
Balls - Ceramic - Sapphire - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).
Related Information:
Balls - Tungsten Carbide
Extreme hardness and wear resistance.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.
Related Information:
Bushes - Plastic - Iglidur J - Flanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur J - Unflanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur Q - Flanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur P - Flanged
Low water absorption. Low wear. Hgh load.
Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur P - Unflanged
Low water absorption. Low wear. Hgh load.
Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur W300 - Flanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur W300 - Unflanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Rollers - Yoke - Cam - Urethane Coated
Urethane tyred cam yoke rollers for noise reduction, reduced wear and non marking. 80 Shore A hardness.
Polycoated shore 80A cast urethane cover.
Related Information:
Bushes - Plastic - Iglidur H370 - Flanged
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur H370 - Unflanged
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Cam Followers - Roller Type - Urethane Covered
Urethane tyred cam followers for noise reduction, reduced wear and non marking
Tool Steel - 496 Oil Hardening - Flat Stock
General purpose tool steel with good wear resistance, durability and machinability
Dimensionally stable chromium, tungsten and vanadium electric furnace toolsteel can be used for intricate work. Low 787 to 815 oC (1450-1500 F) hardening range makes it easy to harden. Fully spheroidised and annealed for uniform carbide size and easy machining. Each piece is individually wrapped and clearly marked with size, analysis and correct hardness and tempering information. Edge squareness 0.003 mm per mm. Finish is 0.0008mm (0.000032 inch).
Bushings - Tension
Like a heavy duty roll pin.
Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications.
Housings - Bearing - Flanged - 2 Bolt Hole - W300
With integral self aligning plain bearing.
Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.
Ball Buttons
Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.
Burnished ground hardened steel.
Mounts - Leveling - Studded - Nickel Plated
Levelling adjusters. Good quality with value pricing. Hardened ball for high load ratings and excellent wear characteristics.
Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces.
Shim and Foil - Brass
Precision brass shim sheet. From very thin foil to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes sheets and rolls. See Brass - Strip for thin strips. Includes K&S Metals range and more.
Related Information:
Bushes - Plastic - Clip - Double Flanged
For use with sheet metal. Used as a light duty split bearing.
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40 oC to 80 oC (minus 40 Deg F to 176 Deg F).
Related Information:
Springs - Constant Force
301 Stainless Steel
Mounting hole specifications will be supplied on request. These springs are usually mounted on a drum and the free end attached to a loading force like a counterbalance. Free ID may vary to meet load specification. Load capacity can be increased by using multiple strips in tandem, back to back or laminated. Be sure to leave at least 40mm coiled on the drum at full extension. The spring ID will wrap tightly on the drum so that most applications require no fastening to the drum.
Related Information:
Rod - Drill - S-7 Air Hardening
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for S-7 hardening requirements.
Bearings - Ball - Ceramic Hybrid
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily. Items with high speed cages have the suffixes T9H, TNH, TW or KC.
Related Information:
Attachments - Cable - Thimbles - Stainless Steel
316 Stainless Steel. Use with synchromesh cable or standard miniature cable. Use with synchromesh or standard miniature cable
Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends.
Related Information:
Bearings - One Way - Sprag - Standard
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
Designed for press fit installation. Correct interference dimensions must be maintained to obtain maximum bearing and clutch performance. Mount the clutch ensuring that the shaft drive directionis in the direction indicated by the arrow on the inner race. To install, use a press tool / do not hammer or apply other stock to clutch. Make sure housing has enough strength to withstand press required for fitting installation. High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes.
Related Information:
Bushes - Plastic - Clip - Bevelled Edge
M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F). Used as a light duty split bearing.
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight.
Related Information:
Inserts - Self Tapping - For Wood - Slotted Drive
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.
Related Information:
Slides - Dovetail
Used for work feeders for production milling, positioning fixutres, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc.
Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type remains parallel and wears less as it occurs over the entire surface. Made of continuous cast GS 40,000 PSI pearlitic grey iron. Able to be milled, drilled, tapped, etc.
Circlips - External - Bevelled
N1402 / VSH / 5102 / 16630. Retaining rings. Snap Rings (USA).
A 15 Deg. bevel on the inside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments.
Related Information:
Inserts - Self Tapping - For Aluminium - Stainless 303
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Inserts - Self Tapping - For Plastics - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
Circlips - Internal - Bevelled
N1302 / VHO / 16631 / 9002 / N5002. Retaining rings. Snap Rings (USA).
A 15 Deg. bevel on the outside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments.
Related Information:
Inserts - Self Tapping - For Aluminium - Stainless 316
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
Inserts - Self Tapping - For Aluminium - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Housings - Linear - Square
Used to maintain radial integrity and eliminate the need for parallel shafting.
Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads.
Nuts - Hexagonal - Binx - Steel
The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
Main Pages
About Us
Balls List
Bearings List
Brands
Catalogue
Contact Us
Charity
Dental Bearings
Dowel Pins
Downloadable PDF Catalogue Ball Lock Pins
Downloadable PDF Catalogue Balls
Downloadable PDF Catalogue Ceramic Bearings
Downloadable PDF Catalogue Circlips
Downloadable PDF Catalogue Clevis Pins
Downloadable PDF Catalogue Corrosion Resistant Bearings
Downloadable PDF Catalogue Disc Springs
Downloadable PDF Catalogue Dowel Pins
Downloadable PDF Catalogue Economy Bearings
Downloadable PDF Catalogue Hammer Drive Pins
Downloadable PDF Catalogue High Speed Bearings
Downloadable PDF Catalogue Key Steel
Downloadable PDF Catalogue Knobs
Downloadable PDF Catalogue Leveling Mounts
Downloadable PDF Catalogue Metallic Bushes
Downloadable PDF Catalogue O-Rings
Downloadable PDF Catalogue Pins
Downloadable PDF Catalogue Plastic Bearings
Downloadable PDF Catalogue Polyvee Belts and Pulleys
Downloadable PDF Catalogue Precision Shim Washers
Downloadable PDF Catalogue Push On and Push In Rings
Downloadable PDF Catalogue Rod & Tube
Downloadable PDF Catalogue Roll Pins
Downloadable PDF Catalogue Shaft Collars
Downloadable PDF Catalogue Shim Sheet
Downloadable PDF Catalogue Shoulder Screws
Downloadable PDF Catalogue Sintered Bronze Bushes
Downloadable PDF Catalogue Snap Rings
Downloadable PDF Catalogue Socket Set Screws
Downloadable PDF Catalogue Solid Bronze Bushes
Downloadable PDF Catalogue Spring Steel Strip
Downloadable PDF Catalogue Springs
Downloadable PDF Catalogue Standard Ball Bearing Range
Downloadable PDF Catalogue Super Precision Bearings
Downloadable PDF Catalogue Taper Pins
Downloadable PDF Catalogue Thrust Bearings
Downloadable PDF Catalogue Thumb Screws and Nuts
Downloadable PDF Catalogue Timing Belts
Downloadable PDF Catalogue Timing Pulley Stock
Downloadable PDF Catalogue Timing Pulleys
Downloadable PDF Catalogue Vibration Mounts
Downloadable PDF Catalogue Washers
Downloadable PDF Catalogue Wave Washers
Downloadable PDF Cross Reference ADR and SKF
Downloadable PDF Cross Reference Anderton Circlips
Downloadable PDF Cross Reference Barden Bearings
Downloadable PDF Cross Reference Essentra
Downloadable PDF Cross Reference Flocast
Downloadable PDF Cross Reference K&S Metals
Downloadable PDF Cross Reference McMaster Carr
Downloadable PDF Cross Reference Miniature Precison Bearings
Downloadable PDF Cross Reference Nordex
Downloadable PDF Cross Reference NSK and NTN
Downloadable PDF Cross Reference Ondrives
Downloadable PDF Cross Reference Reid Supply
Downloadable PDF Cross Reference SDP-SI Designatronics
Downloadable PDF Cross Reference Seeger Circlips
Downloadable PDF Cross Reference Sintered Bronze
Downloadable PDF Cross Reference Small Parts Inc
Downloadable PDF Cross Reference Timing Belts and Pulleys
Freight Rates and Shipping Times
Frequently Asked Questions
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 131167 products in 2163 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
