Small Parts & Bearings - an MBA company

WC10 REID


Cross Referenced Part Numbers



WC100RS Reid part number WC-100



Wheel Diameter: 76.20 x 44.45. Type: Rigid. Tyre material: Phenolic.

Rec. Retail Price: 0.00     
(As low as in bulk)     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     



WC102RS Reid part number WC-102



Wheel Diameter: 76.20 x 44.45. Type: Rigid. Tyre material: Phenolic.

Rec. Retail Price: 0.00     
(As low as in bulk)     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     



WC109RS Reid part number WC-109



Wheel diameter: 76.20 x 25.40. Type: Swivel. Tyre material: Cushionex.

Rec. Retail Price: 0.00     
(As low as in bulk)     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     



WC10RS Reid part number WC-10



Wheel Diameter: 127.00 x 50.80. Type: Swivel. Tyre material: TPR Rubber.

Rec. Retail Price: 0.00     
(As low as in bulk)     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Gears Inch Mitre


Gears - Mitre - 10 Diametrical Pitch - Steel
Gears - Mitre - 10 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:


Plungers Spring


Plungers - Spring - Threaded - Steel - Hi-Life Flat Hexagonal Nose
Plungers - Spring - Threaded - Steel - Hi-Life Flat Hexagonal Nose

Also see combined categories:
All Threaded Spring Plungers

Over 10 million cycles. Built to take the tough abuse of high speed, long run, stamping operations. Ideal for use as parts lifters in dies, or other applications requiring exceptional long life.

Special long life springs. Black oxide finished bodies. Nylon locking element. Not recommended for use in aluminium applications.


Cable


Cable - Miniature - Coated
Cable - Miniature - Coated

Also see combined categories:
All Cable

Lengths will be supplied continuous to a maximum of 3mtrs (ie, 10 x 300mm supplied as 3mtr length)

Recommended that nylon coating is stripped prior to swaging. Sold per length. Multiple quantities will be supplied in a continuous length up to 3mtr maximum. Also called bowden cable.

Related Information:


Cable - Miniature - Uncoated
Cable - Miniature - Uncoated

Also see combined categories:
All Cable

Lengths will be supplied continuous to a maximum of 3mtrs (ie, 10 x 300mm supplied as 3mtr length)

Sold per length. Multiple quantities will be supplied in a continuous length up to 3mtr maximum. Also called bowden cable.

Related Information:


Gears Inch Spur


Gears - Spur - 10DP - 14.5 Degree - Steel
Gears - Spur -  10DP - 14.5 Degree - Steel

Also see combined categories:
All 10DP Spur Gears

PCD = No. of Teeth x 2.540mm (1/10 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 10 Diametrical Pitch. Approx 7.98mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


You may also be interested in

Bumpers


Bumpers - Elastomer - Medium Energy Absorption - Low Reaction Force
Bumpers - Elastomer - Medium Energy Absorption - Low Reaction Force

Also see combined categories:
All Elastomer Bumpers

Elastomer bumpers provide excellent resistance to chemicals and humidity. 20 times greater durability than urethane.

10 greater durability than rubber and 500 times greater than steel coiled springs. Maintains excellent resilience at extreme temperatures and remains flexible with no material degradation between -62 oC and +148 Deg C (-80 Deg F and +300 Deg F). Mounting screws not included.


Bumpers - Elastomer - High Energy Absorption - Compact Size - Short Stroke
Bumpers - Elastomer - High Energy Absorption - Compact Size - Short Stroke

Also see combined categories:
All Elastomer Bumpers

Elastomer bumpers provide excellent resistance to chemicals and humidity. 20 times greater durability than urethane.

10 greater durability than rubber and 500 times greater than steel coiled springs. Maintains excellent resilience at extreme temperatures and remains flexible with no material degradation between -62 oC and +148 Deg C (-80 Deg F and +300 Deg F). Mounting screws not included.


Bumpers - Elastomer - Low Energy Absorption - Longer Stroke - Soft Stop
Bumpers - Elastomer - Low Energy Absorption - Longer Stroke - Soft Stop

Also see combined categories:
All Elastomer Bumpers

Elastomer bumpers provide excellent resistance to chemicals and humidity. 20 times greater durability than urethane.

10 greater durability than rubber and 500 times greater than steel coiled springs. Maintains excellent resilience at extreme temperatures and remains flexible with no material degradation between -62 oC and +148 Deg C (-80 Deg F and +300 Deg F). Mounting screws not included.


Latches Draw


Latches - Draw - T-Handle - Stainless Steel
Latches - Draw - T-Handle - Stainless Steel


Black rubber T Handle with stainless steel bracket and keeper. Shipped assembled. Installs with 4.8mm rivets (3/16 in.) or 10 Gauge Screws. Can be welded. Keeper included.



Nuts Hex


Nuts - Hexagonal - Titanium - Ti-Gr5 - Ti-6Al4v
Nuts - Hexagonal - Titanium - Ti-Gr5 - Ti-6Al4v

Also see combined categories:
All Nuts

Metric. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. Used in critical aircraft structural components. UNS R56400. If the A and H dimensions are critical for your application please consult us prior to ordering. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.


Washers Flat Metallic


Washers - Flat - Titanium - Ti-Gr5 - Ti-6Al4v
Washers - Flat - Titanium - Ti-Gr5 - Ti-6Al4v

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Used in critical aircraft structural components. UNS R56400. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:


Screws Countersunk


Screws - Countersunk - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN7991
Screws - Countersunk - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN7991

Also see combined categories:
All Countersunk Screws

Flat Head Countersunk. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Metric Sizes to DIN7991. Used in critical aircraft structural components. UNS R56400. ISO 10642. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:


Screws Cap Head


Screws - Cap - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN912
Screws - Cap - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN912

Also see combined categories:
All Machine Screws
All Socket Cap Screws

Metric Sizes to DIN912. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:


Screws Hex Head


Screws - Hex Head - Set - Titanium Ti-Gr5 - Ti-6Al4v
Screws - Hex Head - Set - Titanium Ti-Gr5 - Ti-6Al4v

Also see combined categories:
All Hex Head Screws

Fully threaded hex head set screws (DIN933). Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Used in critical aircraft structural components. UNS R56400. Din 933. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:


Balls Metallic


Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI

Also see combined categories:
All Metallic Balls

Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Precision Grade: 200. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Related Information:


Screws Grub


Socket Set Screws - Cup Point - Titanium - Ti-Gr5 - Ti-6Al4v - DIN916
Socket Set Screws - Cup Point - Titanium - Ti-Gr5 - Ti-6Al4v - DIN916

Also see combined categories:
All Non Magnetic Grub Screws
All Grub Screws

Standard DIN916 grub screws with cup point. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:


Socket Set Screws - Flat Tip - Titanium - Ti-Gr5 - Ti-6Al4v - DIN913
Socket Set Screws - Flat Tip - Titanium - Ti-Gr5 - Ti-6Al4v - DIN913

Also see combined categories:
All Non Magnetic Grub Screws
All Grub Screws

Standard DIN913 grub screws with flat end. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:


Balls Metallic


Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded

Also see combined categories:
All Threaded Metallic Balls

Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Precision Grade: 200. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. Threaded either 1-72 UNF or M1.2.

Related Information:


Gears Inch Racks


Gear Racks - 1-10 - Stainless - Tapped Base
Gear Racks -  1-10 - Stainless - Tapped Base

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 416 stainless steel. 1/10th of an inch (2.54mm) tooth pitch.

1/10 Inch (2.54mm) between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Plungers Ball


Plungers - Ball - Threaded - With Limit Switch
Plungers - Ball - Threaded - With Limit Switch

Also see combined categories:
All Threaded Ball Plungers

Suitable for locking and releasing a device by using a built-in electrical switch. Stainless steel spring, nickel plated body, hardened steel ball.

Supply Cable : Grey for normally open contacts, black for normally closed. Oil resistant. Max tensile load 20N. Working Temperature: -10 deg C to 80 deg C. Electrical Supply : 20 mA DC Max. Switching load recommended 5-10 mA. Voltage : 12-24V Supply Cable 3mm - 2 Phase, 2 metres long. Safety Standard : IP40 Average Switch Life Span : 3 milliion switchings.


Shafting Precision Ground


Shafting - Ground - Precision - Titanium - Ti-Gr5 - TC4
Shafting - Ground - Precision - Titanium - Ti-Gr5 - TC4

Also see combined categories:
All Shafting
All Titanium Shafting

Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:


Hobby Gears


Hobby Gears - Spur - Module 0.4
Hobby Gears - Spur - Module 0.4


A small selection of popular Module 0.4 Brass Gear Sets 9 to 20 teeth

See main listings under Gears for sizes not listed here. To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.4 spur gear with 20 teeth has a pitch diameter of 8mm. A module 0.4 spur gear with 10 teeth has a pitch diameter of 4mm.

Related Information:


Hobby Gears - Spur - Module 0.5
Hobby Gears - Spur - Module 0.5


A small selection of popular Module 0.5 Brass Gear Sets 9 to 20 teeth

See main listings under Gears for sizes not listed here. To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.5 spur gear with 20 teeth has a pitch diameter of 10mm. A module 0.5 spur gear with 10 teeth has a pitch diameter of 5mm.

Related Information:


Drylin Bearings and Systems


Drylin Sliding Bearings
Drylin Sliding Bearings


Linear sliding motion. Use with Drylin Aluminium Shafts.

Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: Less than 2 N/mm2. Maximum Speed: 8 m/s (dry) Greater than 10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60oC to +100oC (increased wear when used in excess of 80oC).

Related Information:


Gear Racks - 10DP - 14.5 PA - Steel
Gear Racks - 10DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 10 DP. Approx 7.98mm between teeth. For easy ready selected sets of rack and gear please see the HES website.


Gearheads - Inline - Planetary - Size 17 - Precision
Gearheads - Inline - Planetary - Size  17 - Precision

Also see combined categories:
All Inline Planetary Gearheads

Use with NEMA Size 17 Motors.

Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).

Related Information:


1000 Midwest Parts
1000 Midwest Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


105 MTC Parts
105 MTC Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


10C Kavo Parts
10C Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


10CN Kavo Parts
10CN Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


10000C-1988 Abu Garcia Parts
10000C-1988 Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


10000C Abu Garcia Parts
10000C Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


1000 Abu Garcia Parts
1000 Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Torx 1000 RPM Morita Parts
Torx 1000 RPM Morita Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Bantam 10X Shimano Parts
Bantam 10X Shimano Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Chronarch 100SF Shimano Parts
Chronarch 100SF Shimano Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Procyon 100 HSD Daiwa Parts
Procyon 100 HSD Daiwa Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Micromotor Isolite 100 and 300 Bien Air Parts
Micromotor Isolite 100 and 300 Bien Air Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Top Air 100 Series W.H. Parts
Top Air 100 Series W.H. Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Enclosures - Aluminium - 100 Series
Enclosures - Aluminium - 100 Series

Also see combined categories:
All Enclosures

Great little boxes ready for you to adapt to your mechanical or electrical projects.

Internal guide slots for mounting PCB assemblies vertically. Ideal for housing sensitive electrical, mechanical, pneumatic or hydraulic devices. Provides effective shielding of EMI and RFI. Designed to IP65 of IEC529 and NEMA 4 (dust and hoseproof). The lid incorporates a recessed neoprene gasket.


Gearboxes - Tee - 100.0 x 100.0 x 60.0mm
Gearboxes - Tee - 100.0 x 100.0 x 60.0mm

Also see combined categories:
All Tee Gearboxes

BLHT50 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 100.0 x 75.0 x 44.0mm
Gearboxes - Tee - 100.0 x  75.0 x  44.0mm

Also see combined categories:
All Tee Gearboxes

Bevel Gears - 3.0 to 10.3 Nm. BLHM40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Belts - Vee - 10.0 x 5.5mm - M-3L
Belts - Vee - 10.0 x 5.5mm - M-3L

Also see combined categories:
All Vee Belts 8mm and 10mm Top Width

Miniature and small belts. 10.0mm Top Width x 5.5mm Height.

Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124473 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124473 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.