Small Parts & Bearings - an MBA company

Washers Flat Metallic Categories




Washers - Flat - Brass - Commercial
Washers - Flat - Brass - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Related Information:




Washers - Flat - Hardened Steel
Washers - Flat - Hardened Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.


Related Information:


Washers - Flat - High Tensile
Washers - Flat - High Tensile

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Grade 8 high tensile washers

ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Related Information:


Washers - Flat - Mild Steel
Washers - Flat - Mild Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. Includes fender washers. Zinc plated and unplated listings.

In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Related Information:


Washers - C - Swing
Washers - C - Swing


Cold finished steel, hardened and ground. Black oxide finish.



Washers - Flat - Sintered Bronze - Precision
Washers - Flat - Sintered Bronze - Precision

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat thrust washers made from oil impregnated sintered bronze


Related Information:


Washers - Flat - Stainless Steel 304 - Commercial
Washers - Flat - Stainless Steel 304 - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Related Information:


Washers - Flat - Stainless Steel 316 - Commercial
Washers - Flat - Stainless Steel 316 - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Related Information:






Washers - Flat - Titanium - CP Grade 1
Washers - Flat - Titanium - CP Grade 1

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.

Related Information:


Washers - Flat - Carbon Spring Steel - Precision Shim
Washers - Flat - Carbon Spring Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.

C1010 steel types best suited to arbor shimming.

Related Information:


Washers - Flat - Titanium - Ti-Gr5 - Ti-6Al4v
Washers - Flat - Titanium - Ti-Gr5 - Ti-6Al4v

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Used in critical aircraft structural components. UNS R56400. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:


Washers - C - 303 Stainless Steel
Washers - C - 303 Stainless Steel

Also see combined categories:
All C Washers

Knurled outside edge



Washers - Heavy Duty - Machined - Steel
Washers - Heavy Duty - Machined - Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

Case hardened cold finished steel with black oxide finish.


Related Information:


Washers - Heavy Duty - Machined - Stainless Steel
Washers - Heavy Duty - Machined - Stainless Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

303 Stainless Steel


Related Information:


Washers - Flat - Fibre
Washers - Flat - Fibre

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat red vulcanised fibre washers. Black available on request and sufficient quantity.

Operating temperature up to 105 oC. Tensile strength 6 kg/mm2. Elongation up to 19 percent. Shrinkage up to 3 percent thickness. Water absorption 4 to 70 percent after 24 hours. Density 1 to 1.45 g/cm.

Related Information:


Washers - Flat - Nylon
Washers - Flat - Nylon

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Related Information:










Screws - Thumb - Flat Key Head - Washer Face - Steel
Screws - Thumb - Flat Key Head - Washer Face - Steel

Also see combined categories:
All Thumb Screws

Flat Key head malleable iron screws with an integral washer


Related Information:


Spacers - Arbor
Spacers - Arbor


Flat arbor shim washers with keyway groove.



Washers - Disc Spring - Plastic
Washers - Disc Spring - Plastic

Also see combined categories:
All Disc Springs

Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.


Bumpers - Round - Urethane - Female Washer
Bumpers - Round - Urethane - Female Washer

Also see combined categories:
All Female Bumpers
All Bumpers

With steel core. Washer type has a counterbored hole to accept a socket head cap screw. Flat washer molded inside.



Bearings - Thrust - Ball - Flat - Chrome Steel
Bearings - Thrust - Ball - Flat - Chrome Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:


Bearings - Thrust - Ball - Flat - Stainless Steel
Bearings - Thrust - Ball - Flat - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:


Washers - Self Aligning - Components - Hardened Steel
Washers - Self Aligning - Components - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.

Case Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-G washers are used for clamping mechanical parts with non-parallel surfaces. Designed for screw solidity in compliance with 8.8. Limited for use on flat closed ring areas - not for elongated holes.


Balls - Chrome Steel
Balls - Chrome Steel

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 60-70.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.

Related Information:


Balls - Phosphor Bronze
Balls - Phosphor Bronze

Also see combined categories:
All Metallic Balls

Specific Gravity 8.4

Grades shown are AFBMA / ISO3290-1.

Related Information:


Balls - Steel - Bored
Balls - Steel - Bored

Also see combined categories:
All Metallic Balls - Bored

Bored steel balls as used in steel rod ends.

Hardness: 58-64 Rc. Material: SUJ-2.

Related Information:


Balls - Tungsten Carbide
Balls - Tungsten Carbide

Also see combined categories:
All Metallic Balls

Extreme hardness and wear resistance.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.

Related Information:


Worms - 64DP Series 1 - Metallic
Worms - 64DP Series 1 - Metallic

Also see combined categories:
All Worms
All Imperial Worms

Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.

14.5o Pressure Angle - 1.78o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:


Leadscrew Nuts - Metric - Round - Metallic
Leadscrew Nuts - Metric - Round - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.

Related Information:


Leadscrew Nuts - Metric - Square - Metallic
Leadscrew Nuts - Metric - Square - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Related Information:


Worm Gears - 24DP Series 1 - Metallic
Worm Gears - 24DP Series 1 - Metallic

Also see combined categories:
All Worm Gears
All Imperial Worm Gears

Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.

14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:


Worm Gears - 32DP Series 1 - Metallic
Worm Gears - 32DP Series 1 - Metallic

Also see combined categories:
All Worm Gears
All Imperial Worm Gears

Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:


Worm Gears - 48DP Series 1 - Metallic
Worm Gears - 48DP Series 1 - Metallic

Also see combined categories:
All Worm Gears
All Imperial Worm Gears

Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.

14.5o Pressure Angle - 3.35o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:


Balls - Stainless Steel - 304 Grade
Balls - Stainless Steel - 304 Grade

Also see combined categories:
All Metallic Balls

A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 oC.

Related Information:


Balls - Stainless Steel - 316 Grade
Balls - Stainless Steel - 316 Grade

Also see combined categories:
All Metallic Balls

A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 oC.

Related Information:


Balls - Stainless Steel - 316L Grade
Balls - Stainless Steel - 316L Grade

Also see combined categories:
All Metallic Balls

Easier to machine than standard 316 grade.

316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.

Related Information:


Balls - Stainless Steel - 400 Grade
Balls - Stainless Steel - 400 Grade

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 55-60. Includes 420 and 440C grades

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel.

Related Information:


Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand
Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:


Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:


Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:


Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI

Also see combined categories:
All Metallic Balls

Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Related Information:


Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded

Also see combined categories:
All Threaded Metallic Balls

Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. Threaded either 1-72 UNF or M1.2.

Related Information:





Main Pages

About Us Balls List Bearings List Brands Catalogue Contact Us Charity Dental Bearings Dowel Pins Downloadable PDF Catalogue Ball Lock Pins Downloadable PDF Catalogue Balls Downloadable PDF Catalogue Ceramic Bearings Downloadable PDF Catalogue Circlips Downloadable PDF Catalogue Clevis Pins Downloadable PDF Catalogue Corrosion Resistant Bearings Downloadable PDF Catalogue Disc Springs Downloadable PDF Catalogue Dowel Pins Downloadable PDF Catalogue Economy Bearings Downloadable PDF Catalogue Hammer Drive Pins Downloadable PDF Catalogue High Speed Bearings Downloadable PDF Catalogue Key Steel Downloadable PDF Catalogue Knobs Downloadable PDF Catalogue Leveling Mounts Downloadable PDF Catalogue Metallic Bushes Downloadable PDF Catalogue O-Rings Downloadable PDF Catalogue Pins Downloadable PDF Catalogue Plastic Bearings Downloadable PDF Catalogue Polyvee Belts and Pulleys Downloadable PDF Catalogue Precision Shim Washers Downloadable PDF Catalogue Push On and Push In Rings Downloadable PDF Catalogue Rod & Tube Downloadable PDF Catalogue Roll Pins Downloadable PDF Catalogue Shaft Collars Downloadable PDF Catalogue Shim Sheet Downloadable PDF Catalogue Shoulder Screws Downloadable PDF Catalogue Sintered Bronze Bushes Downloadable PDF Catalogue Snap Rings Downloadable PDF Catalogue Socket Set Screws Downloadable PDF Catalogue Solid Bronze Bushes Downloadable PDF Catalogue Spring Steel Strip Downloadable PDF Catalogue Springs Downloadable PDF Catalogue Standard Ball Bearing Range Downloadable PDF Catalogue Super Precision Bearings Downloadable PDF Catalogue Taper Pins Downloadable PDF Catalogue Thrust Bearings Downloadable PDF Catalogue Thumb Screws and Nuts Downloadable PDF Catalogue Timing Belts Downloadable PDF Catalogue Timing Pulley Stock Downloadable PDF Catalogue Timing Pulleys Downloadable PDF Catalogue Vibration Mounts Downloadable PDF Catalogue Washers Downloadable PDF Catalogue Wave Washers Downloadable PDF Cross Reference ADR and SKF Downloadable PDF Cross Reference Anderton Circlips Downloadable PDF Cross Reference Barden Bearings Downloadable PDF Cross Reference Essentra Downloadable PDF Cross Reference Flocast Downloadable PDF Cross Reference K&S Metals Downloadable PDF Cross Reference McMaster Carr Downloadable PDF Cross Reference Miniature Precison Bearings Downloadable PDF Cross Reference Nordex Downloadable PDF Cross Reference NSK and NTN Downloadable PDF Cross Reference Ondrives Downloadable PDF Cross Reference Reid Supply Downloadable PDF Cross Reference SDP-SI Designatronics Downloadable PDF Cross Reference Seeger Circlips Downloadable PDF Cross Reference Sintered Bronze Downloadable PDF Cross Reference Small Parts Inc Downloadable PDF Cross Reference Timing Belts and Pulleys Freight Rates and Shipping Times Frequently Asked Questions Google Search Hobby Clearance Hobby Information Large Bearings Mailorder Form Order History Ordering Payment and Shipping Privacy Product Showcase Shipping Rates and Times Technical Terms


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 131170 products in 2164 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 131170 products in 2164 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.