Vernier And Disc Dial Sets Categories

Measuring Equipment

Vernier and Disc Dial Sets

Precision Engraved.

2024 Aluminium Black Anodized. Engraving filled with white enamel.

Couplings - Oldham - Complete - Acetal Disk - Set Screw

Also see combined categories:
All Insert and Jaw Type Couplings

0.06 to 44 Nm. Max Speed: 3000 RPM.

Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 ^oC to +60 ^oC. Oldham couplings are designed to transfer torque between two parallel, but not colinear, shafts. They have three discs, one coupled to the input, one coupled to the output, and a centre disc that is joined to the first two by tongue and grooves. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:

Shafting

Couplings - Double Disk - Aluminium

Zero Backlash - High Torsional Stiffness.

Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.

Related Information:

Techical Details

Shafting

Washers - Disc Spring - Ball Bearing Type

Also see combined categories:
All Disc Springs

Specially designed for preloading the outer ring of ball bearings. C1075 steel. Also known as belleville washers.

Ensures perfect bearing positioning with no sideways play. May be used to provide bearing preload. Load tolerance +/- 20% of load shown.

Washers - Disc Spring - Carbon Steel

Also see combined categories:
All Disc Springs

Also known as belleville washers.

Manufactured under strict quality control to conform to DIN 2093.

Washers - Disc Spring - Flange Locking Type

Also see combined categories:
All Disc Springs

Used under the nuts or bolt head in bolted flange joints that are subject to thermal or mechanical shock. Also known as belleville washers.

The discs deflect and move with the bolted joint. Helps to compensate for loosening that may develop preventing damage and leaks caused by thermal expansion, contraction and shock. Made from 17.7 PH Stainless Steel. Temperature range minus 220 to +300^o Celsius. Load tolerance +/- 20% of load shown.

Washers - Disc Spring - Plastic

Also see combined categories:
All Disc Springs

Also known as belleville washers.

Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb^(R) material.

Washers - Disc Spring - Stainless Steel

Also see combined categories:
All Disc Springs

Also known as belleville washers.

Manufactured under strict quality control to conform to DIN 2093.

Washers - Disk Lock

Also see combined categories:
All Serrated Locking Washers
All Lock Washers

Also see Nord Lock and Lockrite washers

Stainless Grade Grade A2 302/316 18-8. Vibration-proof self tightening structural locking device. Maximum Working Temp: +430^oC. DISC-LOCK^(R) has outperformed all other types of loose, washered, threaded or pinned systems. in a wide range of high stress, corrosive, and vibration sensitive applications.

Bearings - Acetal - Disk Cleaning Applications

Special acetal bearings for disk cleaning

Couplings - Oldham - Disks for Clamp Style

Also see combined categories:
All Insert and Jaw Type Couplings
All Oldham Disks

0.06 to 44 Nm. Max Speed: 3000 RPM.

Disk inserts. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:

Hubs to suit clamp style disks

Shafting

Hubs - Gear and Dial - Single

Also see combined categories:
All Hubs

Fairloc^tm Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

Related Information:

Hub Mounting Gears to Suit

Plastic Bearing Oliver Design - Xyratex Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Motors - Vibrating - Pager

Also see combined categories:
All Vibrating Motors

Includes vibrating disc motor

Washers - Nord Lock - Zinc Plated

Also see combined categories:
All Serrated Locking Washers
All Lock Washers

Supplied in pairs

Steel: Hardness HRA 75+/-3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer. Also see Lockrite and Disc Lock washers.

Related Information:

Alternative Style Lockrite Washers

Washers - LockRite - Corrosion Resistant

Also see combined categories:
All Serrated Locking Washers
All Lock Washers

Supplied in pairs. With Delta Protekt coating.

Also see Nordlock and Disk Lock washers.

Related Information:

Alternative Style Nordlock Washers

Inserts - Thread Repair - Recoil Starter Sets

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.

Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.

Inserts - Thread Repair - Helicoil Starter Sets

Also see combined categories:
All Helicoil Inserts and Kits

Helicoil sets include 3 lengths of 1x, 1.5x and 2x the thread diameter. Also included is a tap, an installation tool, a drill and a tang removal tool packed in a sturdy plastic case.

Stainless inserts. Full instructions included. Helicoil kits include a prewinder tool for fine threads or a threaded mandrel for course and metric threads. Metric and Imperial available.

Inserts - Thread Repair - Keylocking Starter Sets

Also see combined categories:
All Keylocking Inserts and Kits

Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.

Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer.

Related Information:

Keysteel Catalogue PDF

Gears - Mitre - 48 Diametrical Pitch - Precision Matched Sets

Also see combined categories:
All Imperial Mitre Gear Sets

Sold as sets - 1:1 Ratio. Stainless steel and aluminium.

Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20^o Pressure Angle. Mitre gear sets provide a 1:1 ratio on a 90^o angle. For easy ready selected sets of 90^o gears please see the HES website.

Related Information:

For simple ready selected sets of 90 degree gears please see the SPB Website

48 DP Bevel Gears Precision Matched Sets