Use with synchromesh or standard miniature cable
Recommended dimensions after crimping:. 1.05 Cable - A=2.59. 2.06 Cable - A=2.64. 2.60 Cable - A=2.72. 3.40 Cable - A=2.80 (3.40 Cable must have outer helical wire removed prior to crimping).
Related Information:
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
Designed for press fit installation. Correct interference dimensions must be maintained to obtain maximum bearing and clutch performance. Mount the clutch ensuring that the shaft drive directionis in the direction indicated by the arrow on the inner race. To install, use a press tool / do not hammer or apply other stock to clutch. Make sure housing has enough strength to withstand press required for fitting installation. High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes.
Related Information:
Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.
This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring. This category may be available in the new MBA online store at
Springs - Drawbar - Stainless Steel.
Related Information:
Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.
This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring. This category may be available in the new MBA online store at
Springs - Drawbar - Zinc Plated.
Related Information:
Low carbon cold drawn steel with zinc plated finish
Any deviations such as angular lifts, shock loads, modifications will result in drastically reduced maximum loads. This category may be available in the new MBA online store at
Hooks - S - Steel.
Galvanised drop forged steel with stainless steel spring
Plated alloy steel
Steel side plates. Electroplated sheaves are turned from cold rolled bar stock.
Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed. This category may be available in the new MBA online store at
Pulleys - Blocks - Eye - Swivel.
Malleable iron
Nickel Plated
Not recommended for lifting.
Carbon steel zinc plated. Complete with nut. Rolled threads. This category may be available in the new MBA online store at
Bolts - Eye - Bent Rod - Steel.
Not recommended for lifting. 304 stainless steel.
Forged self coloured carbon steel. No threads. No capacity rating as this will depend on your modifications.
Forged self coloured carbon steel.
Forged self coloured carbon steel. Should not be used for angular lifts greater than 45
o. Safety swivel hoist rings are recommended for such applications. This category may be available in the new MBA online store at
Bolts - Eye - Full Threaded Shanks - Carbon Steel.
304 Stainless Steel
Forged self coloured carbon steel.
Forged zinc plated carbon steel.
Zinc plated carbon steel. Should not be used for angular lifts greater than 45o. Safety swivel hoist rings are recommended for such applications.
Hot galvanised finished steel with machine thread.
316 Stainless Steel
Hot galvanised finished steel with machine thread.
Any deviations such as angular lifts, shock loads, modifications of the basic forging etc will result in drastically reduced maximum loads.
316 Stainless Steel
Any deviations such as angular lifts, shock loads, modifications of the basic forging etc will result in drastically reduced maximum loads.
Rust proof nickel plated made from finest quality zinc aluminium alloy
Rust proof nickel plated made from solid bronze
Rust proof nickel plated made from solid bronze
Rust proof nickel plated made from finest quality zinc aluminium alloy
Used for connecting two round rods at 90o.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods. This category may be available in the new MBA online store at
Cross Blocks - Heavy Duty - One Knob One Nut.
Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.
Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50
oC. This category may be available in the new MBA online store at
Dampers - Rotary - 2.0 to 3.0 Ncm.
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50
oC. This category may be available in the new MBA online store at
Dampers - Rotary - 5.0 to 15.0 Ncm.
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate. Temp range 0 to 50
oC. Weight: Max 120 grams. This category may be available in the new MBA online store at
Dampers - Rotary - 50 to 400 Ncm.
Vibration dampening
Related Information:
Easy to cut - colour coded - plastic shim sheets. Precision thicknesses.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Made from sturdy polyester. This category may be available in the new MBA online store at
Shim - Plastic.
Related Information:
2.4 to 2200 Nm, 6-80mm Bores
ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8. This category may be available in the new MBA online store at
Elements - Locking.
Up to 3600 RPM - Minus 20 to Plus 60o C. 0.34 to 18 Nm.
Strong, flexible polyurethane or Hyrtel(R) is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60o C / Hyrtel(R) : Minus 40 to Plus 100o C. Precision swaged mechanically crimped hubs. Annealed steel hubs.
Related Information:
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically + / - 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
Related Information:
Similar to R-Clips, but designed for both arms to fit around a shaft groove rather thand having one arm through a bored hole.
Related Information:
Effective way to position heavy loadsquickly and easily. Single pin unit offers high rigidity with small deflection.
0.71 to 1.27 Nm.
303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.
Related Information:
Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.
Extra large fluted handle for quick and easy plunger retraction. Can be fully retracted into the body by pulling up on the handle. Handle is black thermoplastic. Body and pin are steel with black oxide finish. This category may be available in the new MBA online store at
Plungers - Indexing - Large Handle.
Pre hardened to Rockwell 23-30C. Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.
0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000. This category may be available in the new MBA online store at
Couplings - Rigid - Set Screw.
Related Information:
Inch to Metric / Inch to Inch / Metric to Metric. Brass reducing bushes.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub. This category may be available in the new MBA online store at
Reducers - Bore.
Related Information:
Used to cover studded mount bases to provide additional vibration dampening.
Related Information:
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. This category may be available in the new MBA online store at
Balls - Stainless Steel - 316L Grade.
Related Information:
Black Polypropylene easy to grip knobs.
Related Information:
Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.
Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at
Bushings - Drill - Liner Type - Headless.
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.