Tools Cutting
Extensive range of drill bits, from larger standard sizes down to as small as 0.32mm micro miniature sizes. Sutton - PN - Bordo.
Lengths shown are based on standard stock but may vary. This category may be available in the new MBA online store at
Tools - Drill Bits.
Reduced Shanked Drill Bits
Fastening Bushings
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at
Bushings - Drill - Liner Type - Headless.
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at
Bushings - Drill - Slip - With Head.
Tools Bits
Power bits for use with power screwdrivers and drills
This category may be available in the new MBA online store at
Bits - Power.
Fastening Bushings
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Designed to guide, position, and support the cutting tool in a metalworking jig.
You may also be interested in
Thread Inserts
Contains 20 inserts per kit along with a standard tap, drill bit and installation tool. Installation tool is not needed but will make multiple installations easier.
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Shafting General Purpose
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc. This category may be available in the new MBA online store at
Rod - Drill Blanks.
Thread Inserts
Easy to install with a standard tap, bolt and wrench.
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Simply drill and tap the hole to suit the external thread. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Shafting General Purpose
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for A-2 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - A-2 Air Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for O-1 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - O-1 Oil Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for S-7 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - S-7 Air Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for W-1 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - Silversteel - W-1 Water Hardening.
Screws Self Tapping
Zinc chromate. Fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.
Zinc chromate fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.
Shafting Precision Ground
For use with rail supports and open linear bearings
Bumpers
With drilled and counterbored holes for mounting. Neoprene only, no steel plate.
Linear Slides
High capacity, square gib slides are ideal for precision machine tool applications.
The square gib design offers high load capacity and accuracy and withstands force in any direction. Gib is adjustable. Straight line accuracy 0.00254mm. Base is fabricated from A2 tool steel and hardened to Rc58-62. Saddle or riding portion of the slide is fabricated from low carbon steel and can be drilled, tapped and milled for mounting purposes. All slides feature Rulon bearing material for low friction. Stick-slip is virtually non existent as friction at startup and low speeds is virtually eliminated. No lubrication required. Rulon is practically inert to acids, bases and solvents making these slides a good choice for contaminated environments. Temp range minus 240 oC to +300 Deg C.
Bumpers
With drilled and counterbored holes for mounting. Neoprene bonded to steel plate.
With drilled and counterbored holes for mounting. Urethane bonded to steel plate.
Ball Parallels
Used for handling large work in drill presses or band saw machines.
Placed between work and machine so work can be easily moved. Black Oxide finish with 9.525mm hardened steel balls. Balls are exposed both sides of sheet. This category may be available in the new MBA online store at
Parallels - Ball.
Thread Inserts
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Two slots provided in the upper end of the body and are accessible when the knob is in the retracted position. For use with WIP type plungers.
Made from stress proof steel. The power drive tool is used for volume installation of EZ-LOK thread inserts.
Long and short series allen keys.
Alloy Steel Heat Treated. Short Arm DIN 911. Long Arm ANSI B18.3 1986. This category may be available in the new MBA online store at
Tools - Keys - Hex.
General tool sets, screwdriver sets, tap sets, dies sets, hex key sets.
This category may be available in the new MBA online store at
Tools - Sets.
Handy sets of popular sized hex and torx wrenches.
Highest quality 8650 chrome nickel alloy heat treated and finished to resist rust. Ergo style has colour coded handles. Classic style has one piece steel grip handle. Conveniently folds up like a jack knife when not in use. This category may be available in the new MBA online store at
Tools - Sets - Foldup.
Tube benders and cutters
Related Information:
External circlip pliers including standard and ratchet type.
Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected. This category may be available in the new MBA online store at
Tools - Circlip Pliers - External.
Internal circlip pliers including standard and ratchet type.
Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected. This category may be available in the new MBA online store at
Tools - Circlip Pliers - Internal.
Reversible circlip pliers for internal and external circlips.
Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected. This category may be available in the new MBA online store at
Tools - Circlip Pliers - Reversible.
Assists with assembly e-clip application. Each tool is designed to suit one or two sizes only. This category may be available in the new MBA online store at
Tools - E-Clip Applicators.
Used for deburring and smoothing metals.
Used for deburring and smoothing metals.
Used for deburring and smoothing metals.
Butane Torch, Inspection Mirror, Mini Sandblaster, Nibbling Tool, Plastic Scriber, Pick Up Tool Set, Hex Driver Handle for Insert Bits
X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more. This category may be available in the new MBA online store at
Tools - General.
Includes socket wrench for 0-80 size screws
Lengths shown are based on standard stock but may vary. This category may be available in the new MBA online store at
Tools - Nut Drivers.
Lengths shown are based on standard stock but may vary. This category may be available in the new MBA online store at
Tools - Pin Vises.
Number punch and letter punch sets
Lengths shown are based on standard stock but may vary. This category may be available in the new MBA online store at
Tools - Punches.
Lengths shown are based on standard stock but may vary. This category may be available in the new MBA online store at
Tools - Wrenches.
Designed for removing and setting any pull dowel up to 25.40mm.
Puller studs are threaded into the pull dowel and puller. Upward hammering motion with the slide handle is used to remove the dowel and a downward motion is used to set. This category may be available in the new MBA online store at
Tools - Pullers - Dowel Remover and Setter.
Related Information:
The quick and easy way to remove broken screws, bolts, pipes and studs.
Note! You will also need a drill bit of the correct size for each extractor. This category may be available in the new MBA online store at
Tools - Screw Extractors.
Bar and round holders. 16mm, 20.64mm and 25.4mm (inch). Also called a button die stock.
Tungsten Chrome Alloy - Carbon Steel die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
Tungsten Chrome Alloy - Carbon Steel Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.