Tolerance Rings Categories
Rings - Tolerance
Tolerance rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
You may also be interested in
Linear Bearings
Bearings - Linear - Ball - Miniature - Super High Precision
High Precision Corrosion Resistant Miniature Linear Bearings.
High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.
Related Information:
Bearings - Linear - Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear - Ball - Stainless Steel - Closed.
Related Information:
Shafting Precision Ground
Shafting - Ground - Precision - Titanium - High Strength
Titanium shafting available in oversized and undersized tolerances
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
Circlips
Circlips - Internal - Standard - Carbon Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Plain carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Carbon Steel.
Related Information:
Circlips - Internal - Standard - Zinc Plated
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Zinc Plated.
Related Information:
Springs Disc
Washers - Disc Spring - Flange Locking Type
Used under the nuts or bolt head in bolted flange joints that are subject to thermal or mechanical shock.
The discs deflect and move with the bolted joint. Helps to compensate for loosening that may develop preventing damage and leaks caused by thermal expansion, contraction and shock. Made from 17.7 PH Stainless Steel. Temperature range minus 220 to +300o Celsius. Load tolerance +/- 20% of load shown.
Washers - Flat - Brass - Precision Shim
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Precision Tolerances. Standard and laminated brass shim washers.
This category may be available in the new MBA online store at Washers - Flat - Brass - Precision Shim.
Related Information:
Washers - Flat - Copper - Precision Shim
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Precision Tolerances.
This category may be available in the new MBA online store at Washers - Flat - Copper - Precision Shim.
Related Information:
Washers - Flat - Stainless Steel - Precision Shim
Precision Tolerances.
This category may be available in the new MBA online store at Washers - Flat - Stainless Steel - Precision Shim.
Related Information:
Couplings - Neo-Flex
0.71 to 1.27 Nm.
303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.
Related Information:
Circlips - Internal - Standard - Stainless Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Stainless Steel.
Related Information:
Bearings - Ball - Semi-Ground - Sealed
Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127
This category may be available in the new MBA online store at Bearings - Ball - Semi-Ground - Sealed.
Bearings - Ball - Semi-Ground - Shielded
Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127
This category may be available in the new MBA online store at Bearings - Ball - Semi-Ground - Shielded.
Circlips - External - Bevelled
N1402 / VSH / 5102 / 16630. Retaining rings. Snap Rings (USA).
A 15 Deg. bevel on the inside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments. This category may be available in the new MBA online store at Circlips - External - Bevelled.
Related Information:
Magnets - Ceramic Blocks
Low cost, light weight, high energy material
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Feeler Gauge Stock - Stainless
Used for close spacing and extremely tight tolerance situation.
Rc45-55 hardness. 300 grade stainless. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.
Balls - Tungsten Carbide
Extreme hardness and wear resistance.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.
Related Information:
Circlips - Internal - Bevelled
N1302 / VHO / 16631 / 9002 / N5002. Retaining rings. Snap Rings (USA).
A 15 Deg. bevel on the outside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments. This category may be available in the new MBA online store at Circlips - Internal - Bevelled.
Related Information:
Balls - Plastic - Polypropylene
Excellent for liquid level float applications.
Tolerance and sphericity: up to and including 25.4mm diameter = + / -0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.
Related Information:
Washers - Disc Spring - Plastic
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.
Feeler Gauge Stock - C1095 Carbon Steel
Used for close spacing and extremely tight tolerance situation.
Rc48-62 hardness. High carbon steel. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.
Bearings - Ball - 316 Stainless Steel - Single Row - Sealed
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Bushes - Plastic - Iglidur G - Flanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur G - Unflanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Clamps - Gear - Split
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Balls - Plastic - Nylon
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
Related Information:
Bushes - Plastic - Iglidur M250 - Flanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur M250 - Unflanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Clamps - Gear - Screw Type
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Balls - Plastic - Acrylic
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically + / - 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
Related Information:
Balls - Plastic - PTFE
No water absorption. Temperatures up to 288 Deg C.
Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 oC. Unpolished. Specific Gravity: 2.3.
Related Information:
Bushes - Plastic - Iglidur J - Flanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur J - Unflanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bearings - Ball - 316 Stainless Steel - Single Row - Shielded
Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Balls - Ceramic - Ruby - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.
Related Information:
Bushes - Plastic - Iglidur Q - Flanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Balls - Ceramic - Sapphire - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).
Related Information:
Balls - Plastic - Acetal
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Standard Opaque White. Specific Gravity: 1.4.
Related Information:
Bushes - Plastic - Iglidur F - Unflanged
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur W300 - Flanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur W300 - Unflanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Washers - Disc Spring - Ball Bearing Type
Specially designed for preloading the outer ring of ball bearings. C1075 steel. Includes disc springs to DIN 2093.
Ensures perfect bearing positioning with no sideways play. May be used to provide bearing preload. Load tolerance +/- 20% of load shown. This category may be available in the new MBA online store at Washers - Disc Spring - Ball Bearing Type.
Bushes - Plastic - Iglidur H370 - Unflanged
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bearings - U Groove Profile OD
Special OD Bearings.
Contact us for tolerances. This category may be available in the new MBA online store at Bearings - U Groove Profile OD.
Related Information:
Bushes - Plastic - Iglidur A200 - Flanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur A200 - Unflanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur A290 - Unflanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur X - Unflanged
Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.
Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Magnets - Ceramic - 2 Pole - Insulated Aluminium - Press Fit
Extended poles can be lightly machined. Press fit. Insulated aluminium casing.
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Catalogue
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Charity
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
McMaster Carr Cross Reference PDF
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 130404 products in 2013 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
