Small Parts & Bearings - an MBA company

Searched For: Ties Cable With Mounting Holes Categories


Cable Ties


Ties - Cable - With Mounting Holes
Ties - Cable - With Mounting Holes

Also see combined categories:
All Cable Ties

Cable ties with screw mounting holes.

This category may be available in the new MBA online store at Ties - Cable - With Mounting Holes.


Dual Vee - Tracks with Mounting Holes - Stainless Steel
Dual Vee - Tracks with Mounting Holes - Stainless Steel

Also see combined categories:
All Dual Vee Tracks

Vee guide rails for vee grooved track roller guide wheels.

Match Track Size with same size Guide Wheel. This category may be available in the new MBA online store at Dual Vee - Tracks with Mounting Holes - Stainless Steel.

Related Information:


Dual Vee - Tracks with Mounting Holes - Steel
Dual Vee - Tracks with Mounting Holes - Steel

Also see combined categories:
All Dual Vee Tracks

Vee guide rails for vee grooved track roller guide wheels.

Match Track Size with same size Guide Wheel. This category may be available in the new MBA online store at Dual Vee - Tracks with Mounting Holes - Steel.

Related Information:


Switches - Rocker
Switches - Rocker

Also see combined categories:
All Switches

20mm Diameter mounting hole 12V/10amp. On/Off Round Switches with Housing. Illuminates when turned to on position.

Switchs are rated at 10amp @ 600VAC with finger safe screw terminals. This category may be available in the new MBA online store at Switches - Rocker.


Mounts - Levelling - Studded - Hygienic - Anchoring - One Mounting Hole
Mounts - Levelling - Studded - Hygienic - Anchoring - One Mounting Hole

Also see combined categories:
All Male Stud Levelers

Levelling adjusters. ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.

Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.


Mounts - Levelling - Studded - Hygienic - Anchoring - Two Mounting Hole
Mounts - Levelling - Studded - Hygienic - Anchoring - Two Mounting Hole

Also see combined categories:
All Male Stud Levelers

Levelling adjusters. ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.

Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.


Bumpers - Square and Rectangular
Bumpers - Square and Rectangular

Also see combined categories:
All Square Bumpers
All Bumpers

With drilled and counterbored holes for mounting. Neoprene only, no steel plate.

This category may be available in the new MBA online store at Bumpers - Square and Rectangular.


Bumpers - Square and Rectangular - Steel Plated - Neoprene
Bumpers - Square and Rectangular - Steel Plated - Neoprene

Also see combined categories:
All Square Bumpers
All Bumpers

With drilled and counterbored holes for mounting. Neoprene bonded to steel plate.

This category may be available in the new MBA online store at Bumpers - Square and Rectangular - Steel Plated - Neoprene.


Bumpers - Square and Rectangular - Steel Plated - Urethane
Bumpers - Square and Rectangular - Steel Plated - Urethane

Also see combined categories:
All Square Bumpers
All Bumpers

With drilled and counterbored holes for mounting. Urethane bonded to steel plate.

This category may be available in the new MBA online store at Bumpers - Square and Rectangular - Steel Plated - Urethane.


Magnets - Ceramic - 3 Pole - Insulated Aluminium - Tapped Blind Hole
Magnets - Ceramic - 3 Pole - Insulated Aluminium - Tapped Blind Hole

Also see combined categories:
All Magnets
All Ceramic Magnets

Extended poles can be lightly machined. With tapped blind hole in base for mounting. Insulated aluminium casing.

Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.


Slides - Drawer - Heavy Duty - Rail Mounting - Hold In Detent
Slides - Drawer - Heavy Duty - Rail Mounting - Hold In Detent

Also see combined categories:
All Drawer Slides

Used for filing cabinets, utility and industrial truck storage, machine tool drawers, generators and heavy mechanical devices.

Full extension. Includes 32mm hole pattern as well as traditional hole pattern. Designed for units up to 760mm wide. This category may be available in the new MBA online store at Slides - Drawer - Heavy Duty - Rail Mounting - Hold In Detent.


Rail Systems - Miniature Profile
Rail Systems - Miniature Profile

Also see combined categories:
All Linear Slides

Ideal for precision applications where mounting space is limited

Gothic arch grooves at raceway contacts enables slide to sustain loads & movement from any direction. Made from stainless steel or plastic for corrosion resistance. End caps have oil holes for easy relubrication. This category may be available in the new MBA online store at Rail Systems - Miniature Profile.


Springs - Constant Force
Springs - Constant Force


301 Stainless Steel

Mounting hole specifications will be supplied on request. These springs are usually mounted on a drum and the free end attached to a loading force like a counterbalance. Free ID may vary to meet load specification. Load capacity can be increased by using multiple strips in tandem, back to back or laminated. Be sure to leave at least 40mm coiled on the drum at full extension. The spring ID will wrap tightly on the drum so that most applications require no fastening to the drum. This category may be available in the new MBA online store at Springs - Constant Force.

Related Information:


Attachments - Wire Rope Clips - Carbon Steel
Attachments - Wire Rope Clips - Carbon Steel

Also see combined categories:
All Wire Rope Clips

Hot galvanised carbon steel

Furnished with hex nuts. Meet USA Fed. Spec. FF-C-450c, Type I, Class 1. This category may be available in the new MBA online store at Attachments - Wire Rope Clips - Carbon Steel.


Attachments - Wire Rope Clips - Stainless Steel
Attachments - Wire Rope Clips - Stainless Steel

Also see combined categories:
All Wire Rope Clips

304 Stainless Steel

Furnished with hex nuts. Meet USA Fed. Spec. FF-C-450c, Type I, Class 1. This category may be available in the new MBA online store at Attachments - Wire Rope Clips - Stainless Steel.


Attachments - Cable - Eyes
Attachments - Cable - Eyes

Also see combined categories:
All Synchromesh Attachments

Use with synchromesh or standard miniature cable

Recommended dimensions after crimping:. 1.05 Cable - A=2.59. 2.06 Cable - A=2.64. 2.60 Cable - A=2.72. 3.40 Cable - A=2.80 (3.40 Cable must have outer helical wire removed prior to crimping).

Related Information:


Feet - Mounting - Bonded Neoprene - No Stud
Feet - Mounting - Bonded Neoprene - No Stud

Also see combined categories:
All Mounting Feet

Mounting feet let you isolate all types of machinery and equipment from vibration and floor motion.

This category may be available in the new MBA online store at Feet - Mounting - Bonded Neoprene - No Stud.


Feet - Mounting - Bonded Neoprene - With Stud
Feet - Mounting - Bonded Neoprene - With Stud

Also see combined categories:
All Mounting Feet

Mounting feet let you isolate all types of machinery and equipment from vibration and floor motion.

This category may be available in the new MBA online store at Feet - Mounting - Bonded Neoprene - With Stud.


Shock Absorbers - Mounting Blocks
Shock Absorbers - Mounting Blocks


This category may be available in the new MBA online store at Shock Absorbers - Mounting Blocks.


Plungers - Indexing - Cam Action Mounting Blocks
Plungers - Indexing - Cam Action Mounting Blocks


Used with cam action indexing plungers

Mounting blocks are made from steel with black oxide finish. This category may be available in the new MBA online store at Plungers - Indexing - Cam Action Mounting Blocks.

Related Information:


Plungers - Indexing - Locking - With Mounting Plate - Steel
Plungers - Indexing - Locking - With Mounting Plate - Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Spring loaded to work in a variety of applications on both tooling and equipment that require surface mounting. Plunger is hardened and ground. Knob is black matte plastic. Mounting plate is zinc plated steel. Includes rest position for plunger to stay in retracted position. This category may be available in the new MBA online store at Plungers - Indexing - Locking - With Mounting Plate - Steel.


Ties - Cable - Standard
Ties - Cable - Standard

Also see combined categories:
All Cable Ties

Nylon cable ties.

This category may be available in the new MBA online store at Ties - Cable - Standard.


Plungers - Indexing - Non Locking - With Mounting Plate - Steel
Plungers - Indexing - Non Locking - With Mounting Plate - Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Spring loaded to work in a variety of applications on both tooling and equipment that require surface mounting. Plunger is hardened and ground. Knob is black matte plastic. Mounting plate is zinc plated steel. This category may be available in the new MBA online store at Plungers - Indexing - Non Locking - With Mounting Plate - Steel.


Rail Supports - Without Shaft
Rail Supports - Without Shaft

Also see combined categories:
All Shaft Supports

For mounting of linear shafting.

Shafting sold separately. Support is made from aluminium. This category may be available in the new MBA online store at Rail Supports - Without Shaft.

Related Information:


Adjusters - Tilt
Adjusters - Tilt

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Adjustable supports for all kinds of machinery. Mounting feet levelers.

Stem: Mild steel bright zinc plated. Base: Polythene or Polypropylene. Angle of Tilt: 25o from perpendicular. Hexagon Nut: 12mm A/F. Standard colour: Black.

Related Information:


Mounts - Levelling - Studded - Machine - Cushioned
Mounts - Levelling - Studded - Machine - Cushioned


Levelling adjusters. Reduces noise and vibration on heavy machinery, compressors and presses.

High strength aluminium alloy mounting plate is embedded in each pad with two tapped mounting holes for installation on all types of machines. The elastomer compound used in these pads is highly resistant to oil and chemicals. 1/2 UNC thread cold forged x 2.5 inch bolt supplied with each mount. Thousands of tiny suction pockets on the bottom prevent the machine from walking or slipping out of position. This category may be available in the new MBA online store at Mounts - Levelling - Studded - Machine - Cushioned.


Leadscrew Nuts - Imperial - Acme - Bronze
Leadscrew Nuts - Imperial - Acme - Bronze

Also see combined categories:
All Leadscrew Nuts
All Imperial Leadscrew Nuts

Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting

Nut only. Match with appropriate leadscrew. This category may be available in the new MBA online store at Leadscrew Nuts - Imperial - Acme - Bronze.

Related Information:


Leadscrew Nuts - Imperial - Acme - Plastic
Leadscrew Nuts - Imperial - Acme - Plastic

Also see combined categories:
All Leadscrew Nuts
All Imperial Leadscrew Nuts

Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting

This category may be available in the new MBA online store at Leadscrew Nuts - Imperial - Acme - Plastic.

Related Information:


Leadscrew Nuts - Imperial - Supernuts - Acme
Leadscrew Nuts - Imperial - Supernuts - Acme

Also see combined categories:
All Leadscrew Nuts
All Imperial Leadscrew Nuts

Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting

This category may be available in the new MBA online store at Leadscrew Nuts - Imperial - Supernuts - Acme.

Related Information:


Inserts - Thread Repair - Recoil
Inserts - Thread Repair - Recoil

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.

Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.


Grommets - Rubber - EPDM
Grommets - Rubber - EPDM

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

EPDM Rubber Grommets

50 +/-5 Durometer. Easy to install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Grommets - Rubber - Natural
Grommets - Rubber - Natural

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

Natural Rubber Grommets

50 +/-5 Durometer. Easy to Install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Inserts - Thread Repair - Recoil Starter Sets
Inserts - Thread Repair - Recoil Starter Sets

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.

Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.


Gearmotors - DC PM - Size 70x114
Gearmotors - DC PM - Size 70x114

Also see combined categories:
All DC Permanent Magnet Gearmotors

Permanent Magnet.

Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20oC to +60oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.


Cam Followers - Roller Type - Stainless Steel
Cam Followers - Roller Type - Stainless Steel

Also see combined categories:
All Cam Followers

Stainless steel roller type cam followers.

Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.

Related Information:


Inserts - Self Tapping - For Wood - Slotted Drive
Inserts - Self Tapping - For Wood - Slotted Drive

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.

Related Information:


Gearheads - Inline - Planetary - Size 17 - Precision
Gearheads - Inline - Planetary - Size  17 - Precision

Also see combined categories:
All Inline Planetary Gearheads

Use with NEMA Size 17 Motors.

Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).

Related Information:


Bushings - Snap - Closed
Bushings - Snap - Closed


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at Bushings - Snap - Closed.

Related Information:


Bearings - Self Clinching - Miniature - Self Aligning
Bearings - Self Clinching - Miniature - Self Aligning

Also see combined categories:
All Housings with Integral Bearing

Spyraflo pressed steel housings incorporating Abec 3 bearings in a special seat allowing for +/- 5 Deg Misalignment. Improves performance and reduces manufacturing costs and simplify designs. Designed to press into a mounting plate as thin as 1.5mm.

Clinches into a plate bored to the required housing bore. Minimum plate thickness 1.6mm to no maximum. Maximum mounting hardness 100 Rockwell B. Operating temperature Minus 34 oC to Plus 121 Deg C. Compensates for mounting hole tolerances up to 0.07mm. 4.76 to 10mm bores. RoHS, REACH and SVHC environmental compliant.


Rings - Tolerance
Rings - Tolerance


Tolerance rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.

Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.


Inserts - Self Tapping - For Plastics - Steel
Inserts - Self Tapping - For Plastics - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.

Related Information:


Inserts - Self Tapping - For Aluminium - Stainless 303
Inserts - Self Tapping - For Aluminium - Stainless 303

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.

Related Information:


Inserts - Self Tapping - For Aluminium - Steel
Inserts - Self Tapping - For Aluminium - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.

Related Information:


Inserts - Self Tapping - For Aluminium - Stainless 316
Inserts - Self Tapping - For Aluminium - Stainless 316

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.

Related Information:


Adjusters - Rigid
Adjusters - Rigid

Also see combined categories:
All Mounting Feet

Adjustable supports for all kinds of machinery.

Mild steel bright zinc plated. Screwdriver cross recess in base. Use as mounting feet. This category may be available in the new MBA online store at Adjusters - Rigid.

Related Information:


Mounts - Pivotal Levellers - With Stud
Mounts - Pivotal Levellers - With Stud

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Tough bonded neoprene. Patented pivotal leveler keeps equipment level and dampens an average 85% of noise. Adjusters.

The mounting nut which holds the stud is molded into the pad in a steel bracket and rotates freely permitting at least 6.35mm of leveling. Includes stud epoxied into the base mount. This category may be available in the new MBA online store at Mounts - Pivotal Levellers - With Stud.

Related Information:


Cable - Miniature - Coated
Cable - Miniature - Coated

Also see combined categories:
All Cable

Lengths will be supplied continuous to a maximum of 3mtrs (ie, 10 x 300mm supplied as 3mtr length)

Recommended that nylon coating is stripped prior to swaging. Sold per length. Multiple quantities will be supplied in a continuous length up to 3mtr maximum. Also called bowden cable. This category may be available in the new MBA online store at Cable - Miniature - Coated.

Related Information:


Cable - Miniature - Uncoated
Cable - Miniature - Uncoated

Also see combined categories:
All Cable

Lengths will be supplied continuous to a maximum of 3mtrs (ie, 10 x 300mm supplied as 3mtr length)

Sold per length. Multiple quantities will be supplied in a continuous length up to 3mtr maximum. Also called bowden cable. This category may be available in the new MBA online store at Cable - Miniature - Uncoated.

Related Information:


Attachments - Cable - Loop Sleeves
Attachments - Cable - Loop Sleeves


Use with synchromesh or standard miniature cable

This category may be available in the new MBA online store at Attachments - Cable - Loop Sleeves.

Related Information:


Attachments - Cable - Stop Sleeves
Attachments - Cable - Stop Sleeves


Use with synchromesh or standard miniature cable. Use a swaging tool to compress the stop sleeve over the end of the cable.

This category may be available in the new MBA online store at Attachments - Cable - Stop Sleeves.

Related Information:





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 144275 products in 2044 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 144275 products in 2044 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.