Delays on shipments from USA and shipments passing through Singapore
Shipments from the USA are currently experiencing delays due to severe weather conditions. Shipments passing through Singapore are experiencing some minor delays due to Covid restrictions. We will keep you updated if your orders are affected.
Ties Cable Standard Categories
Cable Ties
You may also be interested in
Cable
Attachments - Eyes - Synchromesh
Use with synchromesh or standard miniature cable
Recommended dimensions after crimping:. 1.05 Cable - A=2.59. 2.06 Cable - A=2.64. 2.60 Cable - A=2.72. 3.40 Cable - A=2.80 (3.40 Cable must have outer helical wire removed prior to crimping).
Related Information:
Attachments - Threaded Plugs
Use with synchromesh or standard miniature cable
F and L dimensions are obtained after swaging. Before swaging the fitting is round.
Related Information:
Attachments - Thimbles - Carbon Steel
Hot galvanised carbon steel. Use with synchromesh or standard miniature cable
Meets USA Fed. Spec. FF-T-276b for Type III thimbles.
Related Information:
Attachments - Thimbles - Stainless Steel
316 Stainless Steel. Use with synchromesh cable or standard miniature cable. Use with synchromesh or standard miniature cable
Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends.
Related Information:
Plungers Ball
Plungers - Ball - Threaded - With Limit Switch
Suitable for locking and releasing a device by using a built-in electrical switch. Stainless steel spring, nickel plated body, hardened steel ball.
Supply Cable : Grey for normally open contacts, black for normally closed. Oil resistant. Max tensile load 20N. Working Temperature: -10 deg C to 80 deg C. Electrical Supply : 20 mA DC Max. Switching load recommended 5-10 mA. Voltage : 12-24V Supply Cable 3mm - 2 Phase, 2 metres long. Safety Standard : IP40 Average Switch Life Span : 3 milliion switchings.
Flexible Shaft
Shafts - Flexible - Coupling Ends - Open - Mild Steel
Flexible shafting with coupling ends ready to attach to a fixed shaft.
1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.
Related Information:
Cable Ties
Jockey Wheel Thrust Bearings
Most Common Standard Duty Jockey Wheels Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Rollers
Circlips
Circlips - External - Standard - Berryllium Copper
Imperial and metric DIN471 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Related Information:
Circlips - External - Standard - Carbon Steel
Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Plain carbon steel.
Related Information:
Circlips - External - Standard - Stainless Steel
Imperial and metric DIN471 / D1400 / N1400 / D1460. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel.
Related Information:
Circlips - External - Standard - Zinc Plated
Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel.
Related Information:
Circlips - Internal - Standard - Carbon Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Plain carbon steel. Tolerances on request. Standard and heavy duty options.
Related Information:
Circlips - Internal - Standard - Stainless Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request. Standard and heavy duty options.
Related Information:
Circlips - Internal - Standard - Zinc Plated
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel. Tolerances on request. Standard and heavy duty options.
Related Information:
Collars
Collars - Shaft - Standard - Nylon
Standard one piece nylon shaft collar with set screw
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft.
Related Information:
Collars - Shaft - Standard - Stainless Steel
Includes miniature precision types. 303 and 316 Types.
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft.
Related Information:
Collars - Shaft - Standard - Steel
Includes miniature precision types. Carbon steel.
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft.
Related Information:
Knobs Cross
Pins Dowel
Pins - Dowel - Standard - 303-304 Stainless - Chamfered End
Precision Dowel Pins - 303/304 Grade Stainless - DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends
Precision Dowel Pins - 303/304 Grade Stainless- DIN7
Rounded end dowel pins are measured from the start of the edge rounding. This allows the pin to completely fill the hole after you grind off the rounded end. Diameter tolerances are m6. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 316 Stainless - Chamfered End
Precision Dowel Pins - 316 Grade - DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Precision Dowel Pins - 316 Grade - DIN7
Diameter tolerances are m6. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 416 Stainless - Chamfered End
Precision Dowel Pins - 416 Grade - DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - Chamfered End
Precision Dowel Pins - DIN6325, ISO2338
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends
Precision Dowel Pins - DIN7
Diameter tolerances are m6. Also known as parallel pins.
Related Information:
Studs
Studs - Threaded - Standard
Metric and imperial sizes. Steel and 303 stainless steel.
Yield strength 100,000 PSI. Tensile strength 125,000 PSI.
Couplings Helical and Slit
Couplings - Helical - Standard
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.
Related Information:
Pins - Coiled - Plain - Standard Duty
ASME B18.8.3M / ISO 8750 Standard Duty Spirol Pins. Coiled roll pin.
Related Information:
Pins - Taper - Imperial - Standard - Carbon Steel
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
Related Information:
Pins - Taper - Imperial - Standard - Stainless Steel
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
Related Information:
Couplings - Slit Type - Standard
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
Related Information:
Tools - Rotary Files - Standard Cut
Used for deburring and smoothing metals.
Made from Heat treated steel.
Bearings - One Way - Sprag - Standard
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
Designed for press fit installation. Correct interference dimensions must be maintained to obtain maximum bearing and clutch performance. Mount the clutch ensuring that the shaft drive directionis in the direction indicated by the arrow on the inner race. To install, use a press tool / do not hammer or apply other stock to clutch. Make sure housing has enough strength to withstand press required for fitting installation. High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes.
Related Information:
Cam Followers - Roller Type - Standard
Carbon steel roller type cam followers.
Load 1 applies when outer race is mounted into a housing with standard bearing fit. Load 2 applies when used as a track roller. Stud designed to fit H7 housing.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127000 products in 2359 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
