Tensioners
Use with idler shafts and idler pulleys. Can be mounted on top of any flat surface to provide horizontal tenaioning.
Idler shaft and pulleys not included with tensioner.
Related Information:
Use with idler shafts and idler pulleys. Compact design allows mounting where space is limited.
Idler shaft and pulleys not included with tensioner.
Related Information:
Use with idler shafts and idler pulleys. Fixed base with adjustable arm through 360o.
Idler shaft and pulleys not included with tensioner.
Related Information:
Use with idler shafts and idler pulleys. Uses a screw adjustment for positive precise tensioning.
Idler shaft and pulleys not included with tensioner.
Related Information:
Use with idler shafts and idler pulleys. With flanged base that can be mounted in a tight area.
Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360o controlled tensioning. Serrated teeth to prevent slippage once tightened.
Related Information:
Use with idler shafts and idler pulleys. Adjusting slot assists with precise adjustments.
Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360o controlled tensioning. Serrated teeth to prevent slippage once tightened.
Related Information:
Use with idler shafts and idler pulleys. Mounts on any free point of a fixed shaft allowing controlled tensioning around 360o.
Idler shaft and pulleys not included with tensioner.
Related Information:
Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).
Idler shaft and pulleys not included with tensioner. Shaft is mounted to the side at 90o and is anchored by set screws.
Related Information:
Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).
Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Shaft is located in the centre of the tensioner between the adjusting slots.
Related Information:
Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).
Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Adjusting slots are parallel to each other.
Related Information:
Use with idler shafts and idler pulleys. Has 88.9mm travel and is mounted 90o to the length of the part. Both ends are tapped so the shaft can be threaded on either side of the tensioner.
Idler shaft and pulleys not included with tensioner. Hole is tapped to accept 38.1mm diameter idler shaft (ordered separately).
Related Information:
Use with idler shafts and idler pulleys. Has 88.9mm travel through the use of the vertical slot. Head is drilled and tapped to accept 38.1mm diameter idler shaft (ordered separately).
Idler shaft and pulleys not included with tensioner.
Related Information:
You may also be interested in
Studs
Machine shoulder studs can be used with idlers or tensioner arms
Shafting Precision Ground
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design.
Related Information:
Flat tip grub screws
Related Information:
For running on shafts fixed at the ends.
Related Information:
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass insert.
Related Information:
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64.
Designed to guide, position, and support the cutting tool in a metalworking jig.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 67-69.
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64.
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.
Related Information:
Female 4-40 UNC thread in head allows for secure fixing of studs to a panel.
Each screw comes with two flat washers, 1one lock washer and one hex nut. Yellow chromate zinc finish.
Black Glass Filled Polyamide Bezel, catch and Plug. Brass Shaft. Zinc plated mild steel fixing.
Spacers for printed circuit boards
These spacers have a hex in the centre to allow for holding with a spanner whilst tightening. Fix using a 6 or 8 gauge self tapping screw.
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
Match with rail by rail width dimension. Lightweight construction and easy installation.
Linear guide system with high load carrying capacity, rigity and torque resistance. Rollers are lubricated for life. Base plate anodised aluminium with factory fitted rollers. Elastic elements around the threaded bolts adjust and fix the rollers in the baseplate avoiding risk of mounting error. Supplied with a light preload to cover a wide variety of applications. Load data is for centrally acting loads. For eccentrically acting loads the data should be corrected according to the laws of mechanics. In the case of dynamic loads in the z-direction Fz should be corrected by a factor of 0.6.
Related Information:
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.
Related Information:
RC 65-68
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.
Related Information:
Used in construction of tool, jig and fixture work. 4140L heat treated steel with black oxide finish.
Also known as stripper bolts.
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Used for work feeders for production milling, positioning fixutres, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc.
Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type remains parallel and wears less as it occurs over the entire surface. Made of continuous cast GS 40,000 PSI pearlitic grey iron. Able to be milled, drilled, tapped, etc.
UNC
Carbon steel, black oxide finish. Button Thread nuts allow quick fixturing on long thread lengths. Simply press the button and the threads are disengaged to allow easy movement up or down the screw. Release the button and the threads engage for normal turning.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is hardened and ground smooth. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is hardened and ground smooth. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Insulator shield prevents loss of magnetic flux when inserted into steel components or fixtures
Shielded magnets supply holding forces in limited areas of steel tools, dies and fixtures.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Tang prevents thin gauge material from sliding under plunger.
Brass angle is great for small hobby projects like building scale models or dioramas.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 131248
products in 2171 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.