Small Parts & Bearings - an MBA company

Tension Bushings Categories


Bushings - Tension
Bushings - Tension


Like a heavy duty roll pin.

Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications. This category may be available in the new MBA online store at Bushings - Tension.


Bushings - Snap - Closed
Bushings - Snap - Closed


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at Bushings - Snap - Closed.

Related Information:


Bushings - Snap - Open
Bushings - Snap - Open


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.

Also called a dome plug. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at Bushings - Snap - Open.

Related Information:


Pins - Dowel Bushings
Pins - Dowel Bushings

Also see combined categories:
All Dowel Bushings

Series DB100 Spirol

Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12. This category may be available in the new MBA online store at Pins - Dowel Bushings.

Related Information:


Bushings - QD
Bushings - QD


Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing

Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley. This category may be available in the new MBA online store at Bushings - QD.

Related Information:


Bushings - Taperlock
Bushings - Taperlock


This category may be available in the new MBA online store at Bushings - Taperlock.


Bushings - Spherical - Plastic
Bushings - Spherical - Plastic

Also see combined categories:
All Spherical Bushings

Plastic spherical plain bearings. Also known as ball bushings.

Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.


Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel - With Oil Hole and Wiper Seal.


Bushings - Spherical - Steel - With Oil Hole - Standard
Bushings - Spherical - Steel - With Oil Hole - Standard

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel - With Oil Hole - Standard.


Bushings - Spherical - Steel - Without Oil Hole
Bushings - Spherical - Steel - Without Oil Hole

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel - Without Oil Hole.


Bushings - Spherical - Steel - With Wiper Seal
Bushings - Spherical - Steel - With Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel - With Wiper Seal.


Bushings - Integral Taper
Bushings - Integral Taper

Also see combined categories:
All Locking Assemblies
All Locking Bushings

Stainless Steel Taper Bushings.

Will not mar shafts. This category may be available in the new MBA online store at Bushings - Integral Taper.


Bushings - Drill - Liner Type - Headless - Hardened Steel
Bushings - Drill - Liner Type - Headless - Hardened Steel

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Liner Type - Headless - Hardened Steel.


Bushings - Drill - Press Fit - Headless - Hardened Steel
Bushings - Drill - Press Fit - Headless - Hardened Steel

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Press Fit - Headless - Hardened Steel.


Bushings - Drill - Press Fit - Headless - Tungsten Carbide
Bushings - Drill - Press Fit - Headless - Tungsten Carbide

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 67-69. This category may be available in the new MBA online store at Bushings - Drill - Press Fit - Headless - Tungsten Carbide.


Bushings - Drill - Press Fit - Standard Head - Hardened Steel
Bushings - Drill - Press Fit - Standard Head - Hardened Steel

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Press Fit - Standard Head - Hardened Steel.


Bushings - Drill - Slip - With Head - Hardened Steel
Bushings - Drill - Slip - With Head - Hardened Steel

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Slip - With Head - Hardened Steel.


Bushings - Stroke Rotary - Miniature
Bushings - Stroke Rotary - Miniature

Also see combined categories:
All Stroke Rotary Bushings

2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.

Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.

Related Information:


Bushings - Shoulder
Bushings - Shoulder


This category may be available in the new MBA online store at Bushings - Shoulder.


Mounts - Bonded - Tee Bushing - Centre Bolt
Mounts - Bonded - Tee Bushing - Centre Bolt


Vibration isolation for mobile and static applications involving plate clamping

Reduces structure borne noise and absorbs shock forces. Low profile height. This category may be available in the new MBA online store at Mounts - Bonded - Tee Bushing - Centre Bolt.

Related Information:


Spacers - Machinery Bushings
Spacers - Machinery Bushings

Also see combined categories:
All Round Spacers
All Flat Washers and Spacers - Metallic

Used as spacers between pulleys, gears etc

Low carbon mild steel. This category may be available in the new MBA online store at Spacers - Machinery Bushings.


Dual Vee - Adaptor Bushings
Dual Vee - Adaptor Bushings


Vee grooved track roller bushings.

Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned. This category may be available in the new MBA online store at Dual Vee - Adaptor Bushings.

Related Information:


Elements - Locking
Elements - Locking

Also see combined categories:
All Locking Assemblies

2.4 to 2200 Nm, 6-80mm Bores

ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8. This category may be available in the new MBA online store at Elements - Locking.


Bushes - Plastic Flanged - Iglidur G
Bushes - Plastic Flanged - Iglidur G

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic Unflanged - Iglidur G
Bushes - Plastic Unflanged - Iglidur G

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Pulleys - Vee - B - 5L - Single Row - For QD Bushing

Also see combined categories:
All Vee Pulleys B Section 15.9 and 16.5mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

This category may be available in the new MBA online store at Pulleys - Vee - B - 5L - Single Row - For QD Bushing.

Related Information:


Bushes - Plastic Flanged - Iglidur J
Bushes - Plastic Flanged - Iglidur J

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic Flanged - Iglidur M250
Bushes - Plastic Flanged - Iglidur M250

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic Unflanged - Iglidur J
Bushes - Plastic Unflanged - Iglidur J

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic Unflanged - Iglidur M250
Bushes - Plastic Unflanged - Iglidur M250

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic Flanged - Iglidur Q
Bushes - Plastic Flanged - Iglidur Q

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic Unflanged - Iglidur F
Bushes - Plastic Unflanged - Iglidur F

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Ball Buttons
Ball Buttons


Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.

Burnished ground hardened steel. This category may be available in the new MBA online store at Ball Buttons.


Bushes - Plastic Flanged - Iglidur W300
Bushes - Plastic Flanged - Iglidur W300

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic Unflanged - Iglidur W300
Bushes - Plastic Unflanged - Iglidur W300

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic Unflanged - Iglidur H370
Bushes - Plastic Unflanged - Iglidur H370

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic Flanged - Iglidur A200
Bushes - Plastic Flanged - Iglidur A200

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic Unflanged - Iglidur A200
Bushes - Plastic Unflanged - Iglidur A200

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Grommets - Rubber - EPDM - Standard
Grommets - Rubber - EPDM - Standard

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

EPDM Rubber Grommets

50 +/-5 Durometer. Easy to install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Grommets - Rubber - Natural - Standard
Grommets - Rubber - Natural - Standard

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

Natural Rubber Grommets

50 +/-5 Durometer. Easy to Install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Grommets - Rubber - EPDM - Closed
Grommets - Rubber - EPDM - Closed

Also see combined categories:
All Closed Rubber Grommets
All Rubber Grommets

Closed EPDM Rubber Grommets

50 +/-5 Durometer. Dustproof with Approx 0.5mm thick Membrane. Easy to Install. Dust protection. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Catches - Compression Spring
Catches - Compression Spring


Three internal compression springs supply up to 30kg of spring tension. Available as padlockable or with secondary catch.

Spring tension compensates for gasket set. Provides exact tension for water tight and air tight seals. This category may be available in the new MBA online store at Catches - Compression Spring.


Tensioner - Adjustable Screw
Tensioner - Adjustable Screw

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Uses a screw adjustment for positive precise tensioning.

Idler shaft and pulleys not included with tensioner. This category may be available in the new MBA online store at Tensioner - Adjustable Screw.

Related Information:


Balls - Tooling - Two Piece - Construction - Steel
Balls - Tooling - Two Piece - Construction - Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.

Related Information:


Housings - Pillow Block - Thermoplastic with Stainless Bearing
Housings - Pillow Block - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.


Housings - 3 Bolt Offset - Thermoplastic with Stainless Bearing
Housings - 3 Bolt Offset - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.


Housings - 4 Bolt Flange - Thermoplastic with Stainless Bearing
Housings - 4 Bolt Flange - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.


Bearings - Linear Sliding - Stainless - PTFE - Closed
Bearings - Linear Sliding - Stainless - PTFE - Closed

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000. This category may be available in the new MBA online store at Bearings - Linear Sliding - Stainless - PTFE - Closed.


Bearings - Linear Sliding - Stainless - PTFE - Open
Bearings - Linear Sliding - Stainless - PTFE - Open

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000. This category may be available in the new MBA online store at Bearings - Linear Sliding - Stainless - PTFE - Open.


Housings - Tapped Base - Thermoplastic with Chrome Steel Bearing
Housings - Tapped Base - Thermoplastic with Chrome Steel Bearing


Thermoplastic housed units offer a more favourable economic choice. Hard chrome inserts offer an intermediate level of corrosion resistance.

Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 153543 products in 2089 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 153543 products in 2089 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.