Small Parts & Bearings - an MBA company

Covid-19 Update!! Current supply status.

Trading by online order and email.
Outbound Deliveries: Allow a few extra days for both Australian and overseas deliveries.
Pre-orders and Backorders: Allow a few extra days due to quarantine precautions.

TE25 REID


Cross Referenced Part Numbers



MLV-1700-1270C-GP-B Reid part number TE-25





Load: 1700. Thread Size: 1/2-13 UNC (12.7mm). Hex Flats (B): 19.050.

Online Price: 0.00     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Gearmotors DC


Gearmotors - DC - Size 25 Low Cost
Gearmotors - DC - Size  25 Low Cost


25mm Gearhead Body Diameter. 24.4mm Motor Body Diameter. Low cost. Reversible

D Shaped 4x8mm Output Shaft.


Balls Metallic


Balls - Tungsten Carbide
Balls - Tungsten Carbide

Also see combined categories:
All Metallic Balls

Extreme hardness and wear resistance.

Tolerances available on request. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.

Related Information:


Belts Rounthane


Belts - Rounthane
Belts - Rounthane


Joinable belting. 88 Shore A hardness. Yellow colour. Temperature range -31 to 65 Deg C (-25 to 150 Deg F).

Join with Rounthane Connectors (purchased separately). Material : Non Slip Polyurethane. Use with grooved idler pulleys with diameters at least 8 times the belt width. Purchased per 305mm (1 foot). Orders for more than 1 foot will be supplied as a continuous length. FDA / USDA approved.

Related Information:


Strip


Strip - Spring Steel
Strip - Spring Steel

Also see combined categories:
All Metal Strip

Hundreds of uses.

Hardened and tempered spring steel strip. Note that the width of this strip may vary minus nothing to plus 25 percent as it is guillotine cut from sheet. If you require a closer tolerance on the strip width please contact us prior to ordering.


Adjusters


Adjusters - Tilt
Adjusters - Tilt

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Adjustable supports for all kinds of machinery. Mounting feet levelers.

Stem: Mild steel bright zinc plated. Base: Polythene or Polypropylene. Angle of Tilt: 25o from perpendicular. Hexagon Nut: 12mm A/F. Standard colour: Black.

Related Information:


Universal Joints Single


Universal Joints - Single Joint - High Speed - Solid
Universal Joints - Single Joint - High Speed - Solid

Also see combined categories:
All Universal Joints
All Single Joint Universals

Carbon Steel. Unbored. Maximum operating angle 25 to 45 degrees (refer tables).


Related Information:


Universal Joints - Single Joint - High Speed - Plain Bore
Universal Joints - Single Joint - High Speed - Plain Bore

Also see combined categories:
All Universal Joints
All Single Joint Universals

Carbon Steel. Maximum operating angle 25 to 45 degrees (refer tables).


Related Information:


Universal Joints - Single Joint - Slow Speed - Plain Bore
Universal Joints - Single Joint - Slow Speed - Plain Bore

Also see combined categories:
All Universal Joints
All Single Joint Universals

Carbon Steel. Maximum operating angle 25 to 45 degrees (refer tables). For hand operated applications. Includes miniature sizes from 3mm OD.


Related Information:


Universal Joints - Single Joint - High Speed - Bored and Keyed
Universal Joints - Single Joint - High Speed - Bored and Keyed

Also see combined categories:
All Universal Joints
All Single Joint Universals

Carbon Steel. With keyway. Maximum operating angle 25 to 45 degrees (refer tables).


Related Information:


You may also be interested in

Springs Die


Springs - Die - Imperial - Medium Duty
Springs - Die - Imperial - Medium Duty

Also see combined categories:
All Imperial Die Springs
All All Die Springs

Vapor degassed high tensile strength chromium alloy steel. Spring ends are ground square. Designed for long life cycle with constant high end deflections and shot peened to increase fatigue life.

Colour coded blue. Efficient operating range is 25 to 40 percent of the length. Maximum deflection is 50 percent of the length.

Related Information:


Balls Ceramic


Balls - Ceramic - Ruby - Synthetic
Balls - Ceramic - Ruby - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.

Related Information:


Springs Die


Springs - Die - Imperial - Heavy Duty
Springs - Die - Imperial - Heavy Duty

Also see combined categories:
All Imperial Die Springs
All All Die Springs

Vapor degassed high tensile strength chromium alloy steel. Spring ends are ground square. Designed for long life cycle with constant high end deflections and shot peened to increase fatigue life.

Colour coded gold. Efficient operating range is 15 to 25 percent of the length. Maximum deflection is 30 percent of the length.

Related Information:


Balls Ceramic


Balls - Ceramic - Sapphire - Synthetic
Balls - Ceramic - Sapphire - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).

Related Information:


Drylin Bearings and Systems


Drylin Sliding Bearings
Drylin Sliding Bearings


Linear sliding motion. Use with Drylin Aluminium Shafts.

Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: Less than 2 N/mm2. Maximum Speed: 8 m/s (dry) Greater than 10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60oC to +100oC (increased wear when used in excess of 80oC).

Related Information:


Springs Die


Springs - Die - Imperial - Extra Heavy Duty
Springs - Die - Imperial - Extra Heavy Duty

Also see combined categories:
All Imperial Die Springs
All All Die Springs

Vapor degassed high tensile strength chromium alloy steel. Spring ends are ground square. Designed for long life cycle with constant high end deflections and shot peened to increase fatigue life.

Colour coded green. Efficient operating range is 15 to 20 percent of the length. Maximum deflection is 25 percent of the length.

Related Information:


Springs - Die - Imperial - Medium Duty - Chrome Silicon
Springs - Die - Imperial - Medium Duty - Chrome Silicon

Also see combined categories:
All Imperial Die Springs
All All Die Springs

Chrome silicon die springs are longer lasting than high carbon steel. Shot peened to reduce working stress and to improve the surface.

Colour coded blue. Efficient operating range is 25 to 35 percent of the length. Maximum deflection is 50 percent of the length.

Related Information:


Springs - Die - Imperial - Medium Heavy Duty - Chrome Silicon
Springs - Die - Imperial - Medium Heavy Duty - Chrome Silicon

Also see combined categories:
All Imperial Die Springs
All All Die Springs

Chrome silicon die springs are longer lasting than high carbon steel. Shot peened to reduce working stress and to improve the surface.

Colour coded red. Efficient operating range is 20 to 25 percent of the length. Maximum deflection is 37 percent of the length.

Related Information:


Intra 25LN Kavo Parts
Intra 25LN Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


2500C ICF Abu Garcia Parts
2500C ICF Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


2500 F1 Abu Garcia Parts
2500 F1 Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Intra 25CH Contra Angle Kavo Parts
Intra 25CH Contra Angle Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Gears - Spur - Module 1.25 - Plastic
Gears - Spur - Module 1.25 - Plastic

Also see combined categories:
All Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. Acetal.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 1.25 - Stainless
Gears - Spur - Module 1.25 - Stainless

Also see combined categories:
All Module 1.25 Spur Gears
All Metal Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Sprocket Plates - 6.35 x 2.8mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates -  6.35 x 2.8mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

25-1 ASA 1/4 Inch

Match with 6.35mm simplex chain. American Standard 25-1 - 1/4 inch. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


TLD25 Shimano Parts
TLD25 Shimano Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


W83259 Mars Parts
W83259 Mars Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Pulleys - Timing - 9.525mm Pitch - L - STOCK - Carbon Steel
Pulleys - Timing -  9.525mm Pitch - L - STOCK - Carbon Steel

Also see combined categories:
All L 9.525mm Pitch Timing Pulleys
All L 9.525mm Timing Pulley Stock

For manufacture of timing pulleys or applications requiring multiple belts from a single drive.


Related Information:


625B SuperTorque Kavo Parts
625B SuperTorque Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Sprockets - 6.35 x 2.8mm - Simplex - Carbon Steel - Finished Bore
Sprockets -  6.35 x 2.8mm - Simplex - Carbon Steel - Finished Bore

Also see combined categories:
All Sprockets for Roller Chain

25-1 ASA 1/4 Inch. With finished bore.

Match with 6.35mm simplex chain. American Standard 25-1 - 1/4 inch. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Sprockets - 6.35 x 2.8mm - Simplex - Carbon Steel - Plain Bore
Sprockets -  6.35 x 2.8mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

25-1 ASA 1/4 Inch. With unfinished bore.

Match with 6.35mm simplex chain. American Standard 25-1 - 1/4 inch. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Sprockets - 6.35 x 2.8mm - Simplex - Stainless Steel - Plain Bore
Sprockets -  6.35 x 2.8mm - Simplex  - Stainless Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

25-1 ASA 1/4 Inch. Stainless Steel 303 grade with unfinished bore.

Match with 6.35mm simplex chain. American Standard 25-1 - 1/4 inch. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Motors - DC 25.0x20.1X15.1 mm
Motors - DC 25.0x20.1X15.1 mm

Also see combined categories:
All DC Motors

M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


Motors - DC 25.0X21.0 mm
Motors - DC 25.0X21.0 mm

Also see combined categories:
All DC Motors

M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


Belts - Wedge - 25.4 x 22.2mm - SPP-8V
Belts - Wedge - 25.4 x 22.2mm - SPP-8V


25.4mm Top Width x 22.2mm Height.

Sizes are nominal and may vary slightly.

Related Information:


Circlips - External - Round Section
Circlips - External - Round Section

Also see combined categories:
All External Circlips

DIN7993A / RW / BN825. Retaining rings. Snap Rings (USA).

Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins.

Related Information:


Flanges - Timing Pulley - Suit 9.525mm L Series - Carbon Steel
Flanges - Timing Pulley - Suit  9.525mm L Series - Carbon Steel

Also see combined categories:
All Timing Pulley Flanges

Use with timing pulley stock to custom make your own pulleys


Related Information:


Sprockets - Idler
Sprockets - Idler


Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.

Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.

Related Information:


Calcutta 50-100-150-200-250-251-400-600 Shimano Parts
Calcutta 50-100-150-200-250-251-400-600 Shimano Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Belts - Timing - 10.000mm Pitch - AT10 - 25mm Wide
Belts - Timing - 10.000mm Pitch - AT10 - 25mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 5.000mm Pitch - AT5 - 25mm Wide
Belts - Timing -  5.000mm Pitch - AT5 - 25mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 5.000mm Pitch - GT2 - 25mm Wide
Belts - Timing -  5.000mm Pitch - GT2 - 25mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

GT2 Series Metric Timing Belts.

The TruMotion(R) belt construction utilizes a cream-colored polymer compound reinforced with fiberglass tensile cord and a clean polymer-free nylon tooth facing. The belt can withstand high and low temperature ranges of -40oF to +220oF, has a virtually dust-free operation and is non-marking. The belt also has a high flex life and resistance to elongation. Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 25.4mm Wide
Belts - Timing - 12.700mm Pitch - H - 25.4mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:


Belts - Timing - 5.000mm Pitch - HTD - 25mm Wide
Belts - Timing -  5.000mm Pitch - HTD - 25mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

HTD Series Metric Timing Belts.

Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.08mm. Belt Height (W) - 3.81mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 9.525mm Pitch - L - 25.4mm Wide
Belts - Timing -  9.525mm Pitch - L -  25.4mm Wide

Also see combined categories:
All L 9.525mm Pitch Timing Belts

Standard Series Timing Belts 9.525mm or 0.375 inch pitch.

Pitch (P) - 9.525mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 10.000mm Pitch - T10 - 25mm Wide
Belts - Timing - 10.000mm Pitch - T10 - 25mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

T Series Metric Timing Belts.

Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 5.000mm Pitch - T5 - 25mm Wide
Belts - Timing -  5.000mm Pitch - T5 - 25mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

T Series Metric Timing Belts.

Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 2.65mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.20mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 126925 products in 2503 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 126925 products in 2503 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.