Small Parts & Bearings - an MBA company

Covid-19 Update!! Current supply status.

Trading by online order and email.
Outbound Deliveries: Allow a few extra days for both Australian and overseas deliveries.
Pre-orders and Backorders: Allow a few extra days due to quarantine precautions.

TBS12 ONDRIVES


Cross Referenced Part Numbers



TBS-016-M12 Ondrives part number TBS-12





Diameter of Stud (D1): 16.00. Thread (d2): M12.0 x 1.75. Thickness (d3): 16.00.

Online Price: 0.00     
Stock: 2     


Category Matches

Gearbox Parts


P30-60 Ondrives Parts
P30-60 Ondrives Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Gears - Mitre - 12 Diametrical Pitch - Steel
Gears - Mitre - 12 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:


Gearmotors - DC - Size 12
Gearmotors - DC - Size  12

Also see combined categories:
All DC Gearmotors

12mm Gearhead Body Diameter.



Motors - DC 23.8X30.6 mm
Motors - DC 23.8X30.6 mm

Also see combined categories:
All DC Motors

12 VDC - 12,300 RPM unloaded at 4.5 volts


Related Information:


Motors - DC 20.0X25.0 mm
Motors - DC 20.0X25.0 mm

Also see combined categories:
All DC Motors

1.5 to 4.5 VDC - 12,000 RPM unloaded at 3 volts


Related Information:


Gears - Spur - 12DP - 14.5 Degree - Steel
Gears - Spur -  12DP - 14.5 Degree - Steel

Also see combined categories:
All 12DP Spur Gears

PCD = No. of Teeth x 2.117mm (1/12 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 12 Diametrical Pitch. Approx 6.65mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Washers - Bevel
Washers - Bevel


For use with eyebolts to correct taper when used on I beams and other structural applications. Bevelled 2 in 12 which is standard for flanges of I beams and channels.

Malleable iron with black finish.


O-Rings - Neoprene Rubber
O-Rings - Neoprene Rubber

Also see combined categories:
All O-Rings

Excellent resistance to ageing and weathering effects.

Temperature Range: -20oC to +100oC. Resistant to ozone and refrigeration chemicals such as freon 12 and 22. Moderate resistance to swelling in mineral oils, greases and water. Not resistant to aromatic compounds such as benzene, toulene, chlorinated hydrocarbons, esters, ethers or ketones.

Related Information:


Bearings - Ball - Anti Corrosion - Special Stainless
Bearings - Ball - Anti Corrosion - Special Stainless

Also see combined categories:
All 300 Grade Stainless Bearings

Higher corrosion resistance than 440C stainless - HRC59 Hardness - Same or higher load than 440C

Ideal for applications with salt spray or chemicals in the pH range 3 to 12. ISC CASSTOP design with special TBN-6H stainless steel. Other sizes available on request.

Related Information:


Cranks - Handwheel - Spoked
Cranks - Handwheel - Spoked

Also see combined categories:
All Spoked Handwheel Cranks

Pressed steel with RAL 9005 black epoxy resin coating. Hub: Welded with H9 tolerance plain hole (Type B) or through square H11 tolerance hole (Type V). Axial and radial runout lower than IT 12.


Gear Racks - 12DP - Steel
Gear Racks -  12DP - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

12 DP. Approx 6.65mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Mounts - Leveling - Hygienic - Anchoring - Low Profile - High Swivel
Mounts - Leveling - Hygienic - Anchoring - Low Profile - High Swivel

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.

Operating temperature -20 to 100o C. Wrench flats in thread still allow for full use of threaded section. 12o swivel.

Related Information:


Gearmotors - DC PM - Size 70x114
Gearmotors - DC PM - Size 70x114

Also see combined categories:
All DC Permanent Magnet Gearmotors

Permanent Magnet.

Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20oC to +60oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.


S 12000 RPM Sirona Parts
S 12000 RPM Sirona Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Sprockets - 12.7 x 6.38mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 6.38mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x6.38mm simplex chain (41-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. American Standard 41-1 - 1/2 inch.

Related Information:


Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm duplex chain (08B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch.

Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Taperlock Bored sprockets need to be matched up with a taperlock bush to obtain the correct bore size. British Standard 08B - 1/2 inch. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Sprockets - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.85mm simplex chain (40-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. American Standard 40-1 - 1/2 inch. With and without hubs. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Motors - DC 12.0X30.0 mm
Motors - DC 12.0X30.0 mm

Also see combined categories:
All DC Motors

6.0V - 22800 RPM


Related Information:


Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.85mm simplex chain (40-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Belts - Vee - 12.5 x 9.0mm - A-4L
Belts - Vee - 12.5 x 9.0mm - A-4L

Also see combined categories:
All Vee Belts 12.5mm and 12.7mm Top Width

12.5mm Top Width x 9.0mm Height.

Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.

Related Information:


Belts - Vee - 12.7 x 7.9mm - Notched AX
Belts - Vee - 12.7 x 7.9mm - Notched AX

Also see combined categories:
All Vee Belts 12.5mm and 12.7mm Top Width

12.7mm Top Width x 7.9mm Height.


Related Information:


Belts - Wedge - 12.7 x 10.0mm - SPA
Belts - Wedge - 12.7 x 10.0mm - SPA

Also see combined categories:
All Vee Belts 12.5mm and 12.7mm Top Width

12.7mm Top Width x 10.0mm Height.

Sizes are nominal and may vary slightly.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 15.9mm Wide
Belts - Timing - 12.700mm Pitch - H - 15.9mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 19.1mm Wide
Belts - Timing - 12.700mm Pitch - H - 19.1mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 25.4mm Wide
Belts - Timing - 12.700mm Pitch - H - 25.4mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 38.1mm Wide
Belts - Timing - 12.700mm Pitch - H - 38.1mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 50.8mm Wide
Belts - Timing - 12.700mm Pitch - H - 50.8mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 76.1mm Wide
Belts - Timing - 12.700mm Pitch - H - 76.1mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 9.5mm Wide
Belts - Timing - 12.700mm Pitch - H -  9.5mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Taperlock bush required for bore.

Cast Iron and Steel. Match with a taperlock to suit your bore requirements.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Cast Iron and Steel. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 38.1mm. Taperlock bush required for bore.

Steel and Cast Iron. Match with a taperlock to suit your bore requirements.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 50.8mm. Taperlock bush required for bore.

Steel and Cast Iron. Match with a taperlock to suit your bore requirements.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 76.2mm. Taperlock bush required for bore.

Steel and Cast Iron. Match with a taperlock to suit your bore requirements.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - STOCK - Aluminium
Pulleys - Timing - 12.700mm Pitch - H - STOCK - Aluminium

Also see combined categories:
All H 12.7mm Pitch Timing Pulley Stock

For manufacture of timing pulleys or applications requiring multiple belts from a single drive.


Related Information:


Pulleys - Timing - 12.700mm Pitch - H - STOCK - Carbon Steel
Pulleys - Timing - 12.700mm Pitch - H - STOCK - Carbon Steel

Also see combined categories:
All H 12.7mm Pitch Timing Pulley Stock

For manufacture of timing pulleys or applications requiring multiple belts from a single drive.


Related Information:


Gearmotors - Basic - Hobby - 12.1mm Diameter
Gearmotors - Basic - Hobby - 12.1mm Diameter

Also see combined categories:
All Basic Gearmotors

Small light weight geared motors used in toys and small solar applications

NOTE! These do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.


Sprockets - 19.05 x 12.57mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 19.05 x 12.57mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 19.05x12.57mm simplex steel chain (60-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. American Standard 60-1 - 3/4 inch.

Related Information:


Model Kits - Cars - 1-20th Scale
Model Kits - Cars - 1-20th Scale

Also see combined categories:
All Model Kits
All Model Car Kits

Plastic model kits to build, paint and display. NOT Remote Control.

Brands include Tamiya, Italeri, Academy, Hasegawa.

Related Information:


Flanges - Timing Pulley - Suit 12.700mm H Series - Aluminium
Flanges - Timing Pulley - Suit 12.700mm H Series - Aluminium

Also see combined categories:
All Timing Pulley Flanges

Use with timing pulley stock to custom make your own pulleys


Related Information:


Flanges - Timing Pulley - Suit 12.700mm H Series - Carbon Steel
Flanges - Timing Pulley - Suit 12.700mm H Series - Carbon Steel

Also see combined categories:
All Timing Pulley Flanges

Use with timing pulley stock to custom make your own pulleys


Related Information:


Belts - Timing - 10.000mm Pitch - AT10 - 12mm Wide
Belts - Timing - 10.000mm Pitch - AT10 - 12mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 5.000mm Pitch - AT5 - 12mm Wide
Belts - Timing -  5.000mm Pitch - AT5 - 12mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 126920 products in 2509 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 126920 products in 2509 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.