O-Rings
High thermal resistance and cold flexibility. Some dental applications are included in the listings. Commonly used in food appliactions.
Temperature Range: -70oC to +200oC. Good dialectric properties and resistance to ozone and oxygen attack. Retains flexibility at high and low temperatures. Poor strength and tear resistance. Poor resistance to oils, fuels, concentrated acids and alkalis, water and steam.
Related Information:
Dampers
Damps low frequency vibrations. Vibration dampening
You may also be interested in
Housings with Bearing
Full stainless steel bearing units are the best solution for hostile chemical washdown applications. All metal bearing insert components are a combination of 302, 304 and 440 stainless steel. Seals are silicone rubber. Grease is H-1 food grade.
Operating temperature minus 20 oC to +120 deg C. Solid 304 stainless housings have a machined base and extremely smooth surface finish, essential for demanding washdown installations. These housings do not experience flaking, cracking or discolouration and are virtually unaffected by scrapes. Bearings are removable. Food grade.
Dampers
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50
oC. This category may be available in the new MBA online store at
Dampers - Rotary - 2.0 to 3.0 Ncm.
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50
oC. This category may be available in the new MBA online store at
Dampers - Rotary - 5.0 to 15.0 Ncm.
Tape
Heat Sealer Tape
Non stick ptfe tape is resistant to abrasion, high temperature and chemicals. Commonly used on heatsealing machines, mould protection, packaging, automotive and electrical applications. Temperature range minus 73
oC to 260
oC (-100 to 500 Deg F). Less than 5 percent elongation. This category may be available in the new MBA online store at
Tape - Fiberglass - PTFE Coated.
Replacements for existing tapered roller cones (inner part). Match with part number on your existing bearing. It is recommended that you change both cup and cone whenever possible.
Replacements for existing tapered roller cups (outer part). Match with part number on your existing bearing. It is recommended that you change both cup and cone whenever possible.
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
Threaded externally for easy extraction.
Related Information:
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Miniature sizes.
Related Information:
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Miniature sizes.
Related Information:
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
Related Information:
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
Related Information:
Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um
Related Information:
Metric Sizes Tapered 1:50 and threaded externally for easy extraction.
Related Information:
Metric Sizes Tapered 1:50 and threaded internally for easy extraction.
Related Information:
Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um
Related Information:
Finserts provide strong metal threads in wood, composition board and thermoplastics such as nylon, polystyrene, cellulose acetate and cycolac. By distributing stress over a greater surface area, firm permanent fastening is ensured.
The fins give higher holding strength in softer materials. Available with one, two or three fins for varying material thickness. Finserts prevent splintering, splitting and thread pullout. This category may be available in the new MBA online store at
Inserts - Tapered Fit - Finserts - For Wood and Plastics.
Stainless Steel Taper Bushings.
Press on knobs hold on securely without threads or set screws
Shaft diameter should be +0.000 / - 0.076 mm for best performance. Knob is held in place by a ribbed insert that squeezes onto the shaft. Eliminates machining costs. Knobs will not come off with normal use but can be removed by knocking with a hammer on the underside. This category may be available in the new MBA online store at
Knobs - Oval Tapered - Press On - Phenolic.
Related Information:
Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing
Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley. This category may be available in the new MBA online store at
Bushings - QD.
Related Information:
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges. This category may be available in the new MBA online store at
Bungs and Caps - Reversible - Round.
Related Information:
Match with 12.70x7.75mm simplex chain (08B BS)
Related Information:
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 115mm wide. Taperlock. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 170mm wide. Taperlock. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 40mm wide. Taperlock. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 55mm wide. Taperlock. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 85mm wide. Taperlock. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit GT 5.000mm Pitch Timing Belts. Suits belts 15mm wide. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit GT 5.000mm Pitch Timing Belts. Suits belts 25mm wide. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 12.0mm wide. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 20mm wide. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 30mm wide. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 50mm wide. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 85mm wide. Use with GT2 or GT3 type belts.
Related Information:
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 38.1mm. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 50.8mm. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 76.2mm. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.
Related Information:
Clevis Pins - Keysteel - Rivet Nuts - Rivets - Shim - Screws - U Cushions - Taper Pins - Tubing - Washers
301 Stainless Steel
Mounting hole specifications will be supplied on request. These springs are usually mounted on a drum and the free end attached to a loading force like a counterbalance. Free ID may vary to meet load specification. Load capacity can be increased by using multiple strips in tandem, back to back or laminated. Be sure to leave at least 40mm coiled on the drum at full extension. The spring ID will wrap tightly on the drum so that most applications require no fastening to the drum. This category may be available in the new MBA online store at
Springs - Constant Force.
Related Information:
Metric and Imperial High Speed Steel tap sets including taper, intermediate and bottoming tap in each set
High Speed Steel (HSS) Short Machine taps. Older stock is Triangle Brand (UK). Newer stock is Volkel Brand (German). This category may be available in the new MBA online store at
Tools - Taps - High Speed Steel - Hand - Sets.
Non threaded press fit fastener that doesn't require a reamed hole as do dowel pins.Commonly used in place of taper pins.
An economic method of fastening without the need for precision drilled and reamed holes. Recommended hole tolerance is H11. Total length may be slightly longer than the nominal length. Expanded portion of the pin is compressed into the hole a few thousands of an inch wider than the nominal pin diameter. Radial forces lock the pin securely into the drilled hole. This category may be available in the new MBA online store at
Pins - Groove.
Related Information:
Low cost protection for threaded and cylindrical parts
Elastic snug tight fit protective sleeve fits over straight, tapered or contoured parts. Made from polyethylene. Thickness of web approx 1.8mm. Sold per foot (300mm). Maximum contunuous roll is 100 feet (30 mtrs).
Tapered 3.000 mm per 300 mm (1:100). This category may be available in the new MBA online store at
Keys - Gib Head - Steel.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.