TAPE CATEGORIES
Tape - Fiberglass - PTFE Coated
Heat Sealer Tape
Non stick ptfe tape is resistant to abrasion, high temperature and chemicals. Commonly used on heatsealing machines, mould protection, packaging, automotive and electrical applications. Temperature range minus 73 oC to 260 oC (-100 to 500 Deg F). Less than 5 percent elongation.
Tape - Silicone Wrap
Self fusing silicone wrapping tape for emergency repairs or general protection. Seals leaks. Permanent. Self Bonding. No adhesive. Supa Tape.
Resists Fuels, Oils, Acid, Solvent, Salt Water, Road Salt and UV Rays. Temp Range minus 50 oC to plus 260 deg C. Insulates 8000 Volts (per unstretched layer). Tensile Strength 700psi. Lasts for years with a permanent air tight and water tight seal. Some uses include emergency radiator hose repair, insulation for radioactive areas, garden hose repair, exhaust pipe repair, electrical insulation, tool grips, sporting grips, rope ends, air duct joints, wire bundles. Areas of use include outdoor, auto, marine, workshop, motorcycle, camper, hunting, fishing, farming, plumbing, corrosive areas.
Bearings - Tapered Roller - Cone
Replacements for existing tapered roller cones (inner part). Match with part number on your existing bearing. It is recommended that you change both cup and cone whenever possible.
Bearings - Tapered Roller - Cup
Replacements for existing tapered roller cups (outer part). Match with part number on your existing bearing. It is recommended that you change both cup and cone whenever possible.
Pins - Taper - Imperial - Extractable - External Thread - Stainless Steel
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
Threaded externally for easy extraction.
Related Information:
Pins - Taper - Imperial - Miniature - Carbon Steel
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Miniature sizes.
Related Information:
Pins - Taper - Imperial - Miniature - Stainless Steel
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Miniature sizes.
Related Information:
Pins - Taper - Imperial - Standard - Carbon Steel
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
Related Information:
Pins - Taper - Imperial - Standard - Stainless Steel
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
Related Information:
Pins - Taper - Metric - Carbon Steel
Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um
Metric Sizes to DIN 1.
Related Information:
Pins - Taper - Metric - Extractable - External Thread
Metric Sizes Tapered 1:50 and threaded externally for easy extraction.
DIN 7977. Mild Steel.
Related Information:
Pins - Taper - Metric - Extractable - Internal Thread
Metric Sizes Tapered 1:50 and threaded internally for easy extraction.
DIN 7978. Mild Steel.
Related Information:
Pins - Taper - Metric - Stainless Steel
Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um
Metric Sizes to DIN 1.
Related Information:
Inserts - Tapered Fit - Finserts - For Wood and Plastics
Finserts provide strong metal threads in wood, composition board and thermoplastics such as nylon, polystyrene, cellulose acetate and cycolac. By distributing stress over a greater surface area, firm permanent fastening is ensured.
The fins give higher holding strength in softer materials. Available with one, two or three fins for varying material thickness. Finserts prevent splintering, splitting and thread pullout.
Knobs - Oval Tapered - Press On - Phenolic
Also see combined categories:
All Knobs
All Knobs
Press on knobs hold on securely without threads or set screws
Shaft diameter should be +0.000 / - 0.076 mm for best performance. Knob is held in place by a ribbed insert that squeezes onto the shaft. Eliminates machining costs. Knobs will not come off with normal use but can be removed by knocking with a hammer on the underside.
Related Information:
Bushings - QD
Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing
Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley.
Related Information:
Check Size Before Ordering Giant Tapered OD2 Road Overdrive2 Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bungs and Caps - Reversible - Round
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges.
Related Information:
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock
Match with 12.70x7.75mm simplex chain (08B BS)
Taperlock Bored sprockets need to be matched up with a taperlock bush to obtain the correct bore size. British Standard 08B - 1/2 inch. For easy ready selected sets of chain and sprockets please see the HES website.
Related Information:
Pulleys - Timing - 14.000mm Pitch - GT2 - 115mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 115mm wide. Taperlock
Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 14.000mm Pitch - GT2 - 170mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 170mm wide. Taperlock
Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 14.000mm Pitch - GT2 - 40mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 40mm wide. Taperlock
Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 14.000mm Pitch - GT2 - 55mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 55mm wide. Taperlock
Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 14.000mm Pitch - GT2 - 85mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 85mm wide. Taperlock
Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 5.000mm Pitch - GT2 - 15mm Wide - Taperlock
Timing Pulleys to suit GT 5.000mm Pitch Timing Belts. Suits belts 15mm wide.
Cast iron with black oxide coating. Match with a taperlock bush for your required shaft size.
Related Information:
Pulleys - Timing - 5.000mm Pitch - GT2 - 25mm Wide - Taperlock
Timing Pulleys to suit GT 5.000mm Pitch Timing Belts. Suits belts 25mm wide.
Cast iron with black oxide coating. Match with a taperlock bush for your required shaft size.
Related Information:
Pulleys - Timing - 8.000mm Pitch - GT2 - 12mm Wide - Taperlock
Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 12.0mm wide.
Black Oxide Coated Steel and Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 8.000mm Pitch - GT2 - 20mm Wide - Taperlock
Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 20mm wide.
Black Oxide Coated Steel and Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 8.000mm Pitch - GT2 - 30mm Wide - Taperlock
Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 30mm wide.
Black Oxide Coated Steel and Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 8.000mm Pitch - GT2 - 50mm Wide - Taperlock
Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 50mm wide.
Black Oxide Coated Steel and Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 8.000mm Pitch - GT2 - 85mm Wide - Taperlock
Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 85mm wide.
Black Oxide Coated Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Taperlock
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Taperlock bush required for bore.
Cast Iron and Steel. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Taperlock
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 38.1mm. Taperlock bush required for bore.
Steel and Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Taperlock
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 50.8mm. Taperlock bush required for bore.
Steel and Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 76.2mm. Taperlock bush required for bore.
Steel and Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 9.525mm Pitch - L - 12.7mm Wide - Taperlock
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.
Black oxide coated steel or cast iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 9.525mm Pitch - L - 19.1mm Wide - Taperlock
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.
Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 9.525mm Pitch - L - 25.4mm Wide - Taperlock
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.
Match with a taperlock to suit your bore requirements.
Related Information:
Washers - Bevel
For use with eyebolts to correct taper when used on I beams and other structural applications. Bevelled 2 in 12 which is standard for flanges of I beams and channels.
Malleable iron with black finish.
Tools - Taps - High Speed Steel - Hand - Sets
Metric and Imperial High Speed Steel tap sets including taper, intermediate and bottoming tap in each set
High Speed Steel (HSS) Short Machine taps. Older stock is Triangle Brand (UK). Newer stock is Volkel Brand (German).
Circlips - External - Inverted
N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).
Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.
Related Information:
Dubro Accessories Listed by Description
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings,. Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns,. Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws,. Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders,. Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
Circlips - External - Grooveless
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127031 products in 2352 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
