Small Parts & Bearings - an MBA company

SX88 REID


Cross Referenced Part Numbers



MAV-907-05-102-Z Reid part number SX-880





Load Capacity: 907.184. Thead: 5/8-11 UNC (15.875mm). Thread Length: 101.600.

Online Price: 0.00     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     



MLM-0075-191C-203-S4-M2 Reid part number SX-88





Load: 800. Thread Size: 3/4-10 UNC (19.050mm). Foot Height (B): 22.098.

Online Price: 0.00     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Belts Rounthane


Belts - Rounthane
Belts - Rounthane


Joinable belting. 88 Shore A hardness. Yellow colour. Temperature range -31 to 65 Deg C (-25 to 150 Deg F).

Join with Rounthane Connectors (purchased separately). Material : Non Slip Polyurethane. Use with grooved idler pulleys with diameters at least 8 times the belt width. Purchased per 305mm (1 foot) of length. Orders for more than one length of 305mm will be supplied as a continuous length. FDA / USDA approved.

Related Information:


You may also be interested in

Couplings Other


Couplings - Crowned Tooth Gear - Hubs Only
Couplings - Crowned Tooth Gear - Hubs Only


Match with sleeves from the sleeves category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:


Couplings - Crowned Tooth Gear - Sleeve Only
Couplings - Crowned Tooth Gear - Sleeve Only


Match with hubs from the hubs category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:


Bushes Plastic


Bushes - Plastic - Iglidur A290 - Unflanged
Bushes - Plastic - Iglidur A290 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Sprockets - 15.88 x 9.4mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 15.88 x 9.4mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 15.90x9.4mm steel chain (50-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. American Standard 50-1 - 5/8 inch.

Related Information:


Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 15.90x9.65mm duplex steel chain (10B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch.

Related Information:


Sprocket Plates - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 15.90x9.65mm duplex steel chain (10B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch.

Related Information:


Tensioner - Horizontal Mount
Tensioner - Horizontal Mount

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 88.9mm travel and is mounted 90o to the length of the part. Both ends are tapped so the shaft can be threaded on either side of the tensioner.

Idler shaft and pulleys not included with tensioner. Hole is tapped to accept 38.1mm diameter idler shaft (ordered separately).

Related Information:


Tensioner - Vertical Mount
Tensioner - Vertical Mount

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 88.9mm travel through the use of the vertical slot. Head is drilled and tapped to accept 38.1mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner.

Related Information:


Screws - Cap - Socket - 18-8 Stainless Steel - Nylon Tipped
Screws - Cap - Socket - 18-8 Stainless Steel - Nylon Tipped

Also see combined categories:
All Socket Cap Screws
All Soft Tipped Grub Screws

Nylon tipped socket cap screws in 18-8 Stainless Steel - similar to 316 stainless



Couplings - Eccentric Drive
Couplings - Eccentric Drive


1.88mm bore press fits most standard hobby motors (2mm shaft)



Studs - Full Thread - Stainless Steel
Studs - Full Thread - Stainless Steel

Also see combined categories:
All Studs

18-8 Stainless Steel Allthread Threaded Bar

Short lengths of threaded 18-8 stainless steel bar.


Balls - Plastic - PTFE
Balls - Plastic -  PTFE

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

No water absorption. Temperatures up to 288 Deg C.

Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 oC. Unpolished. Specific Gravity: 2.3.

Related Information:


Gears - Spur - 16DP - 14.5 Degree - Steel
Gears - Spur -  16DP - 14.5 Degree - Steel

Also see combined categories:
All 16DP Spur Gears 14.5 Degree
All Metal 16DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth.


Gears - Spur - 16DP - 20 Degree - Plastic
Gears - Spur -  16DP - 20 Degree - Plastic

Also see combined categories:
All 16DP Spur Gears 20 Degree

PCD = No. of Teeth x 1.588mm (1/16 in.). 20o Pressure Angle. Nylon and acetal. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 128546 products in 2318 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 128546 products in 2318 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.