Small Parts & Bearings - an MBA company

SX79 REID


Cross Referenced Part Numbers



MLM-0075-191C-152-S4-M1 Reid part number SX-79





Load: 800. Thread Size: 3/4-10 UNC (19.050mm). Foot Height (B): 22.098.

Online Price: 0.00     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Bushes Plastic


Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


You may also be interested in

Pins Dowel


Pins - Dowel - Extractable
Pins - Dowel - Extractable

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6. Din 7979.

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.

Related Information:


Wire Rings - External - Round Section
Wire Rings - External - Round Section

Also see combined categories:
All External Circlips

DIN7993A / RW / BN825. Retaining rings. Snap Rings (USA). Round section circlips.

Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins.

Related Information:


Wire Rings - Internal - Round Section
Wire Rings - Internal - Round Section

Also see combined categories:
All Internal Circlips

Includes DIN7993B / RB / M1700 / BN826. Retaining rings. Snap Rings (USA). Round section circlips.

Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins.

Related Information:


Pins - Taper - Metric - Extractable - Internal Thread
Pins - Taper - Metric - Extractable - Internal Thread

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50 and threaded internally for easy extraction.

DIN 7978.

Related Information:


Screws - Countersunk - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN7991
Screws - Countersunk - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN7991

Also see combined categories:
All Countersunk Screws

Flat Head Countersunk. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Metric Sizes to DIN7991. Used in critical aircraft structural components. UNS R56400. ISO 10642. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks.

Related Information:


E-Clips - Basic - Berrylium Copper
E-Clips - Basic - Berrylium Copper

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Berrylium Copper.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip.

Related Information:


E-Clips - Basic - Carbon Steel
E-Clips - Basic - Carbon Steel

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Carbon spring steel including zinc plated and plain.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip. Includes plain and zinc plated.

Related Information:


E-Clips - Basic - Stainless Steel
E-Clips - Basic - Stainless Steel

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Stainless Steel PH15-7 Mo.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip.

Related Information:


Gears - Spur - 32DP - 14.5 Degree - Brass
Gears - Spur -  32DP - 14.5 Degree - Brass

Also see combined categories:
All 32DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth.


Gears - Spur - 32DP - 14.5 Degree - Plastic
Gears - Spur -  32DP - 14.5 Degree - Plastic

Also see combined categories:
All 32DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth.


Gears - Spur - 32DP - 14.5 Degree - Steel
Gears - Spur -  32DP - 14.5 Degree - Steel

Also see combined categories:
All 32DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Carbon steel. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth.


Gears - Spur - 32DP - 20 Degree - Plastic
Gears - Spur -  32DP - 20 Degree - Plastic

Also see combined categories:
All 32DP Spur Gears 20 Degree
All 32DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth.


Gears - Spur - 32DP - 20 Degree - Plastic with Insert
Gears - Spur -  32DP - 20 Degree - Plastic with Insert

Also see combined categories:
All 32DP Spur Gears 20 Degree
All 32DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth.


Washers - Disc Spring - Stainless Steel
Washers - Disc Spring - Stainless Steel

Also see combined categories:
All Disc Springs

Includes disc springs to DIN 2093 and belleville washers to DIN 6796.

Manufactured under strict quality control to conform to DIN 2093.


Pins - Dowel - Extractable - With Vent
Pins - Dowel - Extractable - With Vent

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6 with a ground flat along one edge. DIN7979D.

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650. Also known as parallel pins.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 128552 products in 2319 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 128552 products in 2319 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.