Stroke Rotary Bushings Categories
Bushings - Stroke Rotary - Miniature
2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.
Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.
Related Information:
Bushings - Snap - Closed
Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.
Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at Bushings - Snap - Closed.
Related Information:
Bushings - Snap - Open
Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.
Also called a dome plug. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at Bushings - Snap - Open.
Related Information:
Pins - Dowel Bushings
Series DB100 Spirol
Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12. This category may be available in the new MBA online store at Pins - Dowel Bushings.
Related Information:
Bushings - QD
Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing
Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley. This category may be available in the new MBA online store at Bushings - QD.
Related Information:
Bushings - Taperlock
This category may be available in the new MBA online store at Bushings - Taperlock.
Bushings - Spherical - Plastic
Plastic spherical plain bearings. Also known as ball bushings.
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
Bushings - Spherical - Steel
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel.
Bushings - Spherical - Steel - With Oil Hole
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel - With Oil Hole.
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel - With Oil Hole and Wiper Seal.
Bushings - Spherical - Steel - With Wiper Seal
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel - With Wiper Seal.
Bushings - Integral Taper
Stainless Steel Taper Bushings.
Will not mar shafts. This category may be available in the new MBA online store at Bushings - Integral Taper.
Bushings - Drill - Liner Type - Headless
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Liner Type - Headless.
Bushings - Drill - Press-fit - Headless
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Press-fit - Headless.
Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Designed to guide, position, and support the cutting tool in a metalworking jig.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 67-69. This category may be available in the new MBA online store at Bushings - Drill - Press-fit - Headless - Tungsten Carbide.
Bushings - Drill - Press-fit - Standard Head
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Press-fit - Standard Head.
Bushings - Drill - Slip - With Head
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Slip - With Head.
Bushings - Tension
Like a heavy duty roll pin.
Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications. This category may be available in the new MBA online store at Bushings - Tension.
Bushings - Shoulder
This category may be available in the new MBA online store at Bushings - Shoulder.
Mounts - Bonded - Tee Bushing - Centre Bolt
Vibration isolation for mobile and static applications involving plate clamping
Reduces structure borne noise and absorbs shock forces. Low profile height. This category may be available in the new MBA online store at Mounts - Bonded - Tee Bushing - Centre Bolt.
Related Information:
Spacers - Machinery Bushings
Used as spacers between pulleys, gears etc
Low carbon mild steel. This category may be available in the new MBA online store at Spacers - Machinery Bushings.
Dual Vee - Adaptor Bushings
Vee grooved track roller bushings.
Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned. This category may be available in the new MBA online store at Dual Vee - Adaptor Bushings.
Related Information:
Elements - Locking
2.4 to 2200 Nm, 6-80mm Bores
ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8. This category may be available in the new MBA online store at Elements - Locking.
Bushes - Plastic - Iglidur G - Flanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur G - Unflanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Pulleys - Vee - A - 4L - Single Row - For QD Bushing
Cast iron pulleys. QD bushings are used to vary the bore sizes.
This category may be available in the new MBA online store at Pulleys - Vee - A - 4L - Single Row - For QD Bushing.
Related Information:
Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Cast iron pulleys. QD bushings are used to vary the bore sizes.
This category may be available in the new MBA online store at Pulleys - Vee - B - 5L - Single Row - For QD Bushing.
Related Information:
Bushes - Plastic - Iglidur M250 - Flanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur M250 - Unflanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur J - Flanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur J - Unflanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur Q - Flanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Ball Buttons
Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.
Burnished ground hardened steel. This category may be available in the new MBA online store at Ball Buttons.
Bushes - Plastic - Iglidur F - Unflanged
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur W300 - Flanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur W300 - Unflanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur H370 - Unflanged
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur A200 - Flanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur A200 - Unflanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur A290 - Unflanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur X - Unflanged
Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.
Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Grommets - Rubber - EPDM
EPDM Rubber Grommets
50 +/-5 Durometer. Easy to install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.
Related Information:
Grommets - Rubber - Natural
Natural Rubber Grommets
50 +/-5 Durometer. Easy to Install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.
Related Information:
Grommets - Rubber - EPDM - Closed
Closed EPDM Rubber Grommets
50 +/-5 Durometer. Dustproof with Approx 0.5mm thick Membrane. Easy to Install. Dust protection. Also see snap bushings for a hard plastic product serving a similar purpose.
Related Information:
Catches - Rotary
Polyacetal catch and strike with polyethylene rollers. Ideal in corrosive environments.
This category may be available in the new MBA online store at Catches - Rotary.
Tools - Rotary Files - Aluminium Cut
Used for deburring and smoothing metals.
Made from Heat treated steel. This category may be available in the new MBA online store at Tools - Rotary Files - Aluminium Cut.
Tools - Rotary Files - Double Cut
Used for deburring and smoothing metals.
Made from Heat treated steel. This category may be available in the new MBA online store at Tools - Rotary Files - Double Cut.
Tools - Rotary Files - Standard Cut
Used for deburring and smoothing metals.
Made from Heat treated steel. This category may be available in the new MBA online store at Tools - Rotary Files - Standard Cut.
Dampers - Rotary - 2.0 to 3.0 Ncm
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50 oC. This category may be available in the new MBA online store at Dampers - Rotary - 2.0 to 3.0 Ncm.
Dampers - Rotary - 5.0 to 15.0 Ncm
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50 oC. This category may be available in the new MBA online store at Dampers - Rotary - 5.0 to 15.0 Ncm.
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Catalogue
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Charity
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
McMaster Carr Cross Reference PDF
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 130404 products in 2013 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
