Square Shaft Categories
You may also be interested in
Linear Bearings with Housing
Housings - Linear - Square
Used to maintain radial integrity and eliminate the need for parallel shafting.
Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads.
Square Bar - Brass
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.
Square Bar - Urethane
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Length +/- 2 percent.
Nuts - Square - Machine Screw
For space limited applications. Metts or exceeds ANSI/ASME B18.6.3 standards
Sleeves - Square Hole - Plain - Carbon Steel
Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.
Sleeves - Square Hole - Plain - Hardened
Pre hardened to Rockwell 23-30C. Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.
Sleeves - Square Hole - Threaded - Carbon Steel
Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through and threaded internally at one end.
Bungs - Square
Plastic bungs fit inside square tube.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene.
Related Information:
Tube - Square - Aluminium
Hollow square tubing for general hobby applications.
Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
Related Information:
Tube - Square - Brass
Hollow square tubing for general hobby applications.
Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
Related Information:
Tube - Square - Carbon Fibre - Round Hole
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.
Tube - Square - Carbon Fibre - Square Hole
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.
Bumpers - Square and Rectangle
With drilled and counterbored holes for mounting. Neoprene only, no steel plate.
Bumpers - Square and Rectangle - Steel Plated - Neoprene
With drilled and counterbored holes for mounting. Neoprene bonded to steel plate.
Bumpers - Square and Rectangle - Steel Plated - Urethane
With drilled and counterbored holes for mounting. Urethane bonded to steel plate.
Housings - Bearing - Square - Miniature
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
Balsa Wood - Square
Square section in longer lengths 900mm plus. See block for short lengths. Delivery Surcharges May Apply on Selected Items
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
Related Information:
Keysteel Lengths - Square - Carbon Steel
Plain carbon steel key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.
Related Information:
Keysteel Lengths - Square - Stainless Steel
303, 304 and 316 grade key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.
Related Information:
Keysteel Lengths - Square - Zinc Plated
Zinc plated carbon steel key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled. Zinc plating may be silver or yellow in colour.
Related Information:
Mounts - Bobbin - Square Base
Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening
Fastener may be steel, brass or zinc plated. Natural Rubber isolator.
Housings - Bearing - Flanged - Square - Cast Iron
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
Related Information:
Housings - Bearing - Flanged - Square - W300
With integral self aligning plain bearing.
Housing : Igumid G. Ball : Highly wear resistant Iglidur W300. Temperature range -40 oC to +180 oC.
Leadscrew Nuts - Metric - Square - Metallic
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
Related Information:
Suspension Units - Rubber - Square - Insert Type
Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: +/-30o. Operating Temperature Range: -40oC to +80oC.
Screws - Security - Post Combi Square - Pan Head - Super Zinc
Each 200 pack comes with a Post Combination Driver Bit. Metric only.
Use special tool listed under Screws - Securty - Socket - Tools.
Related Information:
Screws - Security - Post Combi Square - Tools
Metric only.
Used for two hole security screws.
Related Information:
Screws - Set - Cup Point - Square Head
Grade 8 hreat treated alloy steel. All screws are threaded to the head.
Screws - Set - Dog Point - Square Head
Grade 8 hreat treated alloy steel. All screws are threaded to the head.
Pins - Wire Lock Lynch - Double Wire - Square - 304 Stainless Steel
Also known as snapper pins
Related Information:
Pins - Wire Lock Lynch - Double Wire - Square - Carbon Steel
Also known as snapper pins
Related Information:
Pins - Wire Lock Lynch - Single Wire - Square - Carbon Steel
Also known as snapper pins
Related Information:
Balsa Wood - Block
Rectangular and square section short lengths. Delivery Surcharges May Apply on Selected Items
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
Linear Slide Assemblies - Plain - Low Profile - High Load
High capacity, square gib slides are ideal for precision machine tool applications.
The square gib design offers high load capacity and accuracy and withstands force in any direction. Gib is adjustable. Straight line accuracy 0.00254mm. Base is fabricated from A2 tool steel and hardened to Rc58-62. Saddle or riding portion of the slide is fabricated from low carbon steel and can be drilled, tapped and milled for mounting purposes. All slides feature Rulon bearing material for low friction. Stick-slip is virtually non existent as friction at startup and low speeds is virtually eliminated. No lubrication required. Rulon is practically inert to acids, bases and solvents making these slides a good choice for contaminated environments. Temp range minus 240 oC to +300 Deg C.
Handles - Latching - Cab Locks
Zinc finished steel. Accepts 5/16 in. square shank. Inside handle, right or left hand. Picture shown is right hand.
Keys - Machine - Carbon Steel
Form A has rounded ends. Form B has square ends. Form AB has one end rounded and one end square. DIN6884
Related Information:
Keys - Machine - Stainless Steel
Form A has rounded ends. Form B has square ends. Form AB has one end rounded and one end square. DIN6884
Related Information:
Handles - Latching - T-Handle - Folding
Gold zinc finished steel. Die cast construction. 5/16in. Square shank. 360o rotation. Blind mount. Padlockable.
Handles - Latching - 2-Point Locking Rod Kit
Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.
Shafting - Aluminium
Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.
Shafting - Aluminium - Ceramic Coated
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
Related Information:
Shafting - Aluminium - Ceramic Coated - Tapped
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
Related Information:
Main Pages
About Us
Balls
Bearings
Brands
Catalogue
Clearance Items
Contact Us
Contact
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 124481 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
