Spacers
Brass or 303 Stainless Steel
Inexpensive nylon spacers for hobby applications
Shaft spacers - Aluminium
Shaft spacers - Brass
Shaft spacers - Nylon
Shaft spacers - Stainless Steel
Shaft spacers - Steel
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Threaded Hex Spacers. Also known as coupling nuts.
Most items are nickel plated. Refer details recorded against each item.
Threaded Hex Spacers.
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Flat arbor shim washers with keyway groove.
Used as spacers between pulleys, gears etc
Low carbon mild steel.
Spacers for printed circuit boards
These spacers have a hex in the centre to allow for holding with a spanner whilst tightening. Fix using a 6 or 8 gauge self tapping screw.
Handy non marring soft spacer shims in a wedge shape
Level and stabilise appliances, desks, tables, filing cabinets, machinery. Stackable. Vibration cushioning. Ribs ensure that wedges grab tight and stay in place. Black ridid wedges can support up to 2000 lbs. White flexible wedges can be trimmed with a utility knife.
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
Related Information:
Related Information:
Special high impact strength black technopolymer coated with soft touch elastomer chemically bonded (hardness 70 Shore A). Black matte finish. Resistant to solvents, oils, greases and other chemical agents. Zinc plated threaded steel stud.
Related Information:
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges.
Related Information:
Metal Thread Screws. Metric and BSW only. Supplied with nut.
Nuts sold seperately - See Nuts.
Related Information:
Brass metal thread machine screws BSW - UNF - UNC
Nuts sold seperately - See Nuts.
Related Information:
Vibration dampening. Also known as T Bushes or Bonded Mounts.
Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.
Related Information:
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
Related Information:
Metal Thread Screws. Metric and BSW only. Supplied with nut.
Nuts sold seperately - See Nuts.
Related Information:
Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through and threaded internally at one end.
Bar and round holders. 16mm, 20.64mm and 25.4mm (inch). Also called a button die stock.
DIN984 / D2000 / Seeger JK. Retaining rings. Snap Rings (USA).
Internal tabs are concentrically positioned for a concealed assembly. Tabs act as spacers for securing machine components.
Related Information:
Nickel plated round rings
Metric Only
Nuts sold seperately - See Nuts.
Related Information:
UNC - UNF
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
Related Information:
Plastic bungs fit inside round tube.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene.
Related Information:
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
Related Information:
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
Related Information:
Sintered bronze rod is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight. B438 grade 1, Type 2 - AMS4805-D. SAE 841 Type 1, Class A.
Related Information:
For general hobby applications. This rod is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths for general hobby applications. Not recommended for heavy duty applications. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
Related Information:
Hard urethane rubber compound. Machinable.
Length +/- 3.2mm. Diameter +/- 2 percent.
Related Information:
Plastic tips fit over outside of tubing.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene. Tips may be supplied tapered or cylindrical depending on stock availability.
Hollow round tubing for general hobby applications.
For general hobby applications. Includes K&S Metals range and more. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. E-mail sales@smallparts.com.au with enquiries.
Related Information:
Hollow round tubing for general hobby applications.
For general hobby applications. Includes K&S Metals range and more. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. E-mail sales@smallparts.com.au with enquiries.
Related Information:
Hollow round tubing for general hobby applications.
For general hobby applications. Includes K&S Metals range and more. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. E-mail sales@smallparts.com.au with enquiries.
Related Information:
Oil impregnated sintered bronze tubing - self lubricating. Product will machine to the sizes listed and is supplied will be larger on OD and smaller on bore.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on ID to allow for machining. B438 grade 1, Type 2 - AMS4805-D. SAE 841 Type 1, Class A.
Related Information:
For general hobby applications. This tube is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths for general hobby applications. Includes K&S Metals range and more. Not recommended for heavy duty applications. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft.
Hollow round tubing for general hobby applications.
For general hobby applications. Includes K&S Metals range and more. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft.
Related Information:
With steel core.
With steel core. Washer type has a counterbored hole to accept a socket head cap screw. Flat washer molded inside.
With steel core.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is hardened and ground smooth. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 131248
products in 2171 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.