Small Parts & Bearings - an MBA company

SP75 ANDERTON


Cross Referenced Part Numbers



WRE-0750-SR Anderton part number SP75



Shaft or Bearing OD Size (d1): 75.00. Clip ID Max (d3): 70.40. Clip Thickness (s +/- 0.02): 1.60 - 1.70.

Rec. Retail Price: 0.00     
(As low as in bulk)     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Gearboxes Cross Axis


Gearboxes - Cross Axis - 90 x 75 x 32mm
Gearboxes - Cross Axis -  90 x  75 x  32mm

Also see combined categories:
All Cross Axis Gearboxes

Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Related Information:


You may also be interested in

Washers Serrated Locking


Washers - Nord Lock - Zinc Plated
Washers - Nord Lock - Zinc Plated

Also see combined categories:
All Serrated Locking Washers
All Lock Washers

Supplied in pairs

Steel: Hardness HRA 75+/-3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer. Also see Lockrite and Disc Lock washers.

Related Information:


Fishing Reel Parts


7500 8500 Spinning Reel Penn Parts
7500 8500 Spinning Reel Penn Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Bushes Plastic


Bushes - Plastic - Iglidur P - Flanged
Bushes - Plastic - Iglidur P - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur P - Unflanged
Bushes - Plastic - Iglidur P - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Dental Handpiece Parts


757 Lares Parts
757 Lares Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Fishing Reel Parts


7500 Abu Garcia Parts
7500 Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Chain and Sprockets Roller


Sprockets - 3.75 x 1.6mm - Simplex - Plastic
Sprockets -  3.75 x 1.6mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 3.75mm miniature plastic or stainless chain.

Related Information:


Sprockets - 3.75 x 1.6mm - Simplex - Stainless Steel - Plain Bore
Sprockets -  3.75 x 1.6mm - Simplex - Stainless Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Miniature 3.75mm Pitch.

Match with 3.75mm simplex chain. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


MRI Table Bearings


5177597 GE Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Chain and Sprockets Roller


Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm duplex chain (08B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch.

Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Taperlock Bored sprockets need to be matched up with a taperlock bush to obtain the correct bore size. British Standard 08B - 1/2 inch. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Gears Metric Spur


Gears - Spur - Module 0.75 - Brass
Gears - Spur - Module 0.75 - Brass


PCD = No. of Teeth x 0.750mm. 20o Pressure Angle. Brass.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears Metric Stem


Gears - Spur - Module 0.75 - Stem - Brass
Gears - Spur - Module 0.75 - Stem - Brass


Gears with integral shafts.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Chain and Sprockets Roller


Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Snap Rings - External - Basic
Snap Rings - External - Basic

Also see combined categories:
All External Snaprings

Includes series M3200 / SP / ESP / M2400 / SW snaprings. Similar to a circlip without the lugs.

Carbon sping steel. Used on the outside diameter of a bearing, shaft or similar equipment.


Bushes - Plastic - Rulon J - Flanged
Bushes - Plastic - Rulon J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)

Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288 oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon(R) product range.

Related Information:


Bushes - Plastic - Rulon J - Unflanged
Bushes - Plastic - Rulon J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)

Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288 oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon(R) product range.

Related Information:


Gearboxes - Tee - 75.0 x 50.0 x 50.0mm
Gearboxes - Tee -  75.0 x  50.0 x 50.0mm

Also see combined categories:
All Tee Gearboxes

BL8 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Bevel: Medium Carbon Steel 080M40(EN8). Backlash: 1o. Lubrication: Greased for life - Shell Nerita Grease HV.


Gearboxes - Tee - 75.0 x 75.0 x 44.0mm
Gearboxes - Tee -  75.0 x  75.0 x 44.0mm

Also see combined categories:
All Tee Gearboxes

BLHT40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 100.0 x 75.0 x 44.0mm
Gearboxes - Tee - 100.0 x  75.0 x  44.0mm

Also see combined categories:
All Tee Gearboxes

Bevel Gears - 3.0 to 10.3 Nm. BLHM40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Inline - Epicyclic - 115.0 x 75.0 x 75.0mm
Gearboxes - Inline - Epicyclic - 115.0 x  75.0 x  75.0mm

Also see combined categories:
All Inline Epicyclic Gearboxes

Servo Gearbox 35Nm to 50Nm ratios 9:1 - 36:1. EHD08 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Gears: Steel EN36 655M13 EN24T 817M40T. Weight: 2.1kg Backlash: 1o30'. Max Input Speed: 4,000 Rpm (short term). Lubrication: Greased for life - Shell Nerita Grease HV.

Related Information:


Gearboxes - Inline - Epicyclic - 80.0 x 75.0 x 75.0mm
Gearboxes - Inline - Epicyclic -  80.0 x  75.0 x  75.0mm

Also see combined categories:
All Inline Epicyclic Gearboxes

Servo Gearbox 20Nm to 50Nm ratios 3:1 - 6:1. EHD08 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Gears: Steel EN36 655M13 EN24T 817M40T. Weight: 1.4kg Backlash: 30'. Max Input Speed: 4,000 Rpm (short term). Lubrication: Greased for life - Shell Nerita Grease HV.

Related Information:


Sheet - Aluminium - T7075
Sheet - Aluminium - T7075

Also see combined categories:
All Sheet
All Aluminium Sheet

Non precision inexpensive aluminium sheet for hobby applications. Heat-treated T7075 grade.

Sheet for applications not requiring absolute precision. Thickness tolerances +/- 0.1mm. Lengths and widths will be at least that specified but may be more.


Gearboxes - Right Angle - Model RA 0750-0440-0440 - 75.0 x 44.0 x 44.0mm
Gearboxes - Right Angle - Model RA 0750-0440-0440 - 75.0 x  44.0 x  44.0mm

Also see combined categories:
All Right Angle Gearboxes

Bevel Gears - 1.6 Nm-5.0 Nm ratios 6:1 to 24:1. BLN20 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Gear: Steel 655M13 (EN36) Hardened. Backlash: Depends on ratio. Max. Input Speed: 4000 Rpm. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Right Angle - Model RA 0750-0750-0440 - 75.0 x 75.0 x 44.0mm
Gearboxes - Right Angle - Model RA 0750-0750-0440 - 75.0 x  75.0 x 44.0mm

Also see combined categories:
All Right Angle Gearboxes

BLH40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Related Information:


Sprockets - Idler
Sprockets - Idler

Also see combined categories:
All Sprockets for Roller Chain

Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.

Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.

Related Information:


Gearboxes - Offset - 175 x 150 x 60
Gearboxes - Offset - 175 x 150 x  60

Also see combined categories:
All Offset Gearboxes

FF30 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Gear: High Carbon Steel 817M40(EN24). Weight 5.5kg. Backlash: 1o. Hours Life: 12000 hr. Max Input Speed: 1500 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. You will need to assess duty, cycles and confirm gearbox suitability with your own calculations. Torque figures are to be used for guidance only.

Related Information:


Gears - Spur - 8DP - 14.5 Degree - Steel
Gears - Spur -   8DP - 14.5 Degree - Steel

Also see combined categories:
All 8DP Spur Gears

PCD = No. of Teeth x 3.175mm (1/8 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 8 Diametrical Pitch. Approx 9.98mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Mitre - Module 2.75 - Steel
Gears - Mitre - Module 2.75 - Steel

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:


Gear Racks - Module 0.75 - Brass
Gear Racks - Module 0.75 - Brass

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 0.75 - Stainless
Gear Racks - Module 0.75 - Stainless

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Stainless Steel.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Pins - Coiled - Plain - Standard Duty
Pins - Coiled - Plain - Standard Duty

Also see combined categories:
All Coiled Pins

ASME B18.8.3M / ISO 8750 Standard Duty Spirol Pins. Coiled roll pin.


Related Information:


Couplings - Sleeve Type - Hubs
Couplings - Sleeve Type - Hubs


0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:


Couplings - Sleeve Type - Sleeves
Couplings - Sleeve Type - Sleeves


0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:


Gear Racks - Flexible
Gear Racks - Flexible

Also see combined categories:
All Flexible Gear Racks

Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.

20o Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.


Washers - Disc Spring - Ball Bearing Type
Washers - Disc Spring - Ball Bearing Type

Also see combined categories:
All Disc Springs

Specially designed for preloading the outer ring of ball bearings. C1075 steel. Also known as belleville washers.

Ensures perfect bearing positioning with no sideways play. May be used to provide bearing preload. Load tolerance +/- 20% of load shown.


Spa Jet Motor Multiple Parts
Spa Jet Motor Multiple Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Splined Shafts - Stainless Steel
Splined Shafts - Stainless Steel


Externally splined shafting. Bushes not included. Match with same size splined bushes.

Match bushes and shafts by Major Diameter. Steel on Steel is not meant for sliding applications. Steel on Bronze is OK for intermittent sliding under load.


Spiral Rings - External - Heavy Duty
Spiral Rings - External - Heavy Duty

Also see combined categories:
All External Spiral Rings

AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Spring Steel and Stainless Steel.

Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2.


Spiral Rings - External - Medium Duty
Spiral Rings - External - Medium Duty

Also see combined categories:
All External Spiral Rings

AE / WS / AS3218 / RS / MIL-R-27426A1 - Spring Steel and Stainless Steel.

Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AE, Smalley: WS, Spirolox and Ramsey: RS, Aerospace AS3218, MIL-R-27426A1.


Spiral Rings - External - Medium-Heavy Duty
Spiral Rings - External - Medium-Heavy Duty

Also see combined categories:
All External Spiral Rings

AME / WST / RST - Spring Steel and Stainless Steel.

Originally designed to fit NAS50-51 grooves, this series is a popular OEM specification. This two/three turn design is easier to install than the heavy duty RRN option. Equivalent to Associated Spring: AME, Smalley: WST, Spirolox and Ramsey: RST.


Spiral Rings - Internal - Heavy Duty
Spiral Rings - Internal - Heavy Duty

Also see combined categories:
All Internal Spiral Rings

Includes AHI / WHM / AS3215 / Spirolox RRN / MIL-R-27426B2 - Spring Steel and Stainless Steel.

Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHI, Smalley: WHM, Spirolox and Ramsey: RRN, Aerospace AS3215, MIL-R-27426B2.


Spiral Rings - Internal - Light Duty
Spiral Rings - Internal - Light Duty

Also see combined categories:
All Internal Spiral Rings

Includes series CI / VH / UR - Spring Steel and Stainless Steel.

Light duty rings for use in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CI, Smalley: VH, Spirolox and Ramsey: UR.


Spiral Rings - Internal - Medium Duty
Spiral Rings - Internal - Medium Duty

Also see combined categories:
All Internal Spiral Rings

Includes AI / WH / AS3217 / RR / MIL-R-27426B1 - Spring Steel and Stainless Steel.

Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AI, Smalley: WH, Spirolox and Ramsey: RR, Aerospace AS3217, MIL-R-27426B1.


Spiral Rings - Internal - Medium-Heavy Duty
Spiral Rings - Internal - Medium-Heavy Duty

Also see combined categories:
All Internal Spiral Rings

Includes Series AMI / WHT / Spirolox RRT - Spring Steel and Stainless Steel.

Originally designed to fit NAS50-51 grooves, this series is a popular OEM specification. This two/three turn design is easier to install than the heavy duty RRN option. Equivalent to Associated Spring: AMI, Smalley: WHT, Spirolox and Ramsey: RRT.


Spacers - Arbor
Spacers - Arbor


Flat arbor shim washers with keyway groove.



Spacers - Hex - Threaded - 303-304 Stainless Steel
Spacers - Hex - Threaded - 303-304 Stainless Steel

Also see combined categories:
All Threaded Hex Spacers

Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.



Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124473 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124473 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.