Screws Grub
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Standard DIN913 grub screws. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at
Socket Set Screws - Cup Point - Titanium - CP Grade 1 - DIN916.
Related Information:
Standard DIN916 grub screws with cup point. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Related Information:
Includes miniature precision types. 303 and 316 Types.
Related Information:
UNC - UNF - METRIC.
Related Information:
UNC - UNF - METRIC - Stainless Steel.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC - Stainless Steel
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks. This category may be available in the new MBA online store at
Screws - Countersunk - Socket - 316 Stainless.
Related Information:
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
Related Information:
Solder tipped grub screws. Allow fine adjustment and spreads over the contacting surface so as not to mark or deform it.
Related Information:
Grub screws that grip rough shafts.
Related Information:
Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.
Related Information:
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Rolling ball tip for locating into a hole
Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. This category may be available in the new MBA online store at
Socket Set Screws - Rolling Ball Tip - Stainless Steel.
Related Information:
Standard DIN913 grub screws with flat end. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Related Information:
Nylon tipped socket cap screws in 18-8 Stainless Steel - similar to 316 stainless
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Standard one piece nylon shaft collar with set screw
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at
Collars - Shaft - Standard - Nylon.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
440C Stainless Steel heat treated to 55-58 RC.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
440C Stainless Steel heat treated to 55-58 RC.
Related Information:
316L Stainless Steel. Other sizes available on request.
Hexagon socket cap head with low head. Safety improvements and compact size for equipment and devices. May be used in vacuum chamber applications in clean rooms, Flat Panel Displays, Semiconductor production equipment and devices. All clean washed, preventing the inclusion of oil and foreign particles. This category may be available in the new MBA online store at
Screws - Low Head - Socket - 316L Stainless.
Used to replace screws where the need to remove the pin is unlikely.
Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Cone point grub screws
Related Information:
Dog point grub screws
Related Information:
Half Dog Point grub screws
Related Information:
UNC - UNF - METRIC.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC - Stainless Steel
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks. This category may be available in the new MBA online store at
Screws - Countersunk - Socket - 304 Stainless.
Related Information:
Metric only.
Related Information:
UNC - UNF - METRIC - Stainless Steel.
Related Information:
Precision Dowel Pins - 316 Grade - Based on DIN6325, ISO2338, ISO 8734
Related Information:
Precision Dowel Pins - 316 Grade - Based on DIN7
Related Information:
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. This category may be available in the new MBA online store at
Balls - Stainless Steel - 316L Grade.
Related Information:
316 Stainless Steel. Use with synchromesh cable or standard miniature cable. Use with synchromesh or standard miniature cable
Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends. This category may be available in the new MBA online store at
Attachments - Cable - Thimbles - Stainless Steel.
Related Information:
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Levelling adjusters. For levelling machine tools, electronic racks, benches etc on uneven surfaces.
Levelling adjusters. 15o swivel off centreline to adjust to uneven surfaces and level machine tools, electronic racks and benches.
0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000. This category may be available in the new MBA online store at
Couplings - Rigid - Set Screw.
Related Information:
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Includes miniature precision types. Carbon steel.
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at
Collars - Shaft - Standard - Steel.
Related Information:
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
Related Information:
Grade 8 hreat treated alloy steel. All screws are threaded to the head.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.