Balls Metallic
Hardness: Rockwell C: 60-70.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833. This category may be available in the new MBA online store at
Balls - Chrome Steel.
Related Information:
Specific Gravity 8.4
Grades shown are AFBMA / ISO3290-1. This category may be available in the new MBA online store at
Balls - Phosphor Bronze.
Related Information:
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2. This category may be available in the new MBA online store at
Balls - Steel - Bored.
Related Information:
Extreme hardness and wear resistance.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.
Related Information:
Gears Inch Worms
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 1.78o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Leadscrews
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
Related Information:
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
Related Information:
Washers Flat Metallic
Cold finished steel, case hardened with a black oxide finish.
Cold finished steel, hardened and ground. Black oxide finish.
Gears Inch Worms
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 3.35o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Balls Metallic
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000
oC. This category may be available in the new MBA online store at
Balls - Stainless Steel - 304 Grade.
Related Information:
A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000
oC. This category may be available in the new MBA online store at
Balls - Stainless Steel - 316 Grade.
Related Information:
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. This category may be available in the new MBA online store at
Balls - Stainless Steel - 316L Grade.
Related Information:
Hardness: Rockwell C: 55-60. Includes 420 and 440C grades
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel. This category may be available in the new MBA online store at
Balls - Stainless Steel - 400 Grade.
Related Information:
Washers Flat Metallic
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at
Washers - Flat - Brass - Commercial.
Related Information:
Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.
Related Information:
Grade 8 high tensile washers
ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at
Washers - Flat - High Tensile.
Related Information:
Flat washers. Includes fender washers. Zinc plated and unplated listings.
In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at
Washers - Flat - Mild Steel.
Related Information:
Flat washers.
Related Information:
Precision Tolerances. Standard and laminated brass shim washers.
Related Information:
Precision Tolerances.
Related Information:
Flat thrust washers made from oil impregnated sintered bronze
Related Information:
Case hardened cold finished steel with black oxide finish.
Related Information:
Flat washers.
Related Information:
Flat washers.
Related Information:
Precision Tolerances.
Related Information:
Heat treated. Black oxide finish.
Related Information:
Flat washers. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at
Washers - Flat - Titanium - CP Grade 1.
Related Information:
303 Stainless Steel
Related Information:
Gears Metric Worms
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Balls Metallic
Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm
2. Yield Strength 77.5kgf / mm
2. Elongation 10 Percent. This category may be available in the new MBA online store at
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI.
Related Information:
Washers Flat Metallic
Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.
Related Information:
Balls Metallic
Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. Threaded either 1-72 UNF or M1.2.
Related Information:
You may also be interested in
Bearings Plates
Oil impregnated porous bronze sheet.
Screws Button Head
Sheet metal screws
Related Information:
Shim
Precision steel shim sheet. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes K&S Metals range and more. This category may be available in the new MBA online store at
Shim - Tin.
Precision shim sheet. Cold rolled steel. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes K&S Metals range and more. This category may be available in the new MBA online store at
Shim and Foil - Steel.
Related Information:
Precision aluminium shim sheet. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Coloured shim is anodised. The colour is not removable. The colour is for identification purposes only. Includes K&S Metals range and more. Includes listings on 1100, 3003, 6061-T6 and commercial grades aluminium sheet.
Precision brass shim sheet. From very thin foil to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes sheets and rolls. See Brass - Strip for thin strips. Includes K&S Metals range and more.
Related Information:
Precision copper shim sheet. Very thin foil to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes K&S Metals range and more. This category may be available in the new MBA online store at
Shim and Foil - Copper.
Bushes Plastic
Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)
Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288
oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon
(R) product range. This category may be available in the new MBA online store at
Bushes - Plastic - Rulon J - Flanged.
Related Information:
Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)
Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288
oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon
(R) product range. This category may be available in the new MBA online store at
Bushes - Plastic - Rulon J - Unflanged.
Related Information:
Shim
Precision stainless shim sheet. Very thin foil to thick sizes. Includes 302, 304 and 430 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes K&S Metals range and more. This category may be available in the new MBA online store at
Shim and Foil - Stainless Steel.
Related Information:
Bushes Plastic
For use with sheet metal. Used as a light duty split bearing.
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40
oC to 80
oC (minus 40 Deg F to 176 Deg F). This category may be available in the new MBA online store at
Bushes - Plastic - Clip - Double Flanged.
Related Information:
Magnets Rubber and Vinyl
Magnetic Vinyl Sheets and Magnetic Rubber Strip
Shim
Easy to cut - colour coded - plastic shim sheets. Precision thicknesses.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Made from sturdy polyester. This category may be available in the new MBA online store at
Shim - Plastic.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138616
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.