Small Parts & Bearings - an MBA company

Shafts Flexible Coupling Ends Open Mild Steel Categories


Flexible Shaft


Shafts - Flexible - Coupling Ends - Open - Mild Steel
Shafts - Flexible - Coupling Ends - Open - Mild Steel

Also see combined categories:
All Coupling End Flexible Shaft

Flexible shafting with coupling ends ready to attach to a fixed shaft.

1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.

Related Information:


You may also be interested in

Couplings Other


Couplings - Neo-Flex
Couplings - Neo-Flex


0.71 to 1.27 Nm.

303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.

Related Information:


Couplings - Slit Type - Standard
Couplings - Slit Type - Standard

Also see combined categories:
All Helical and Slit Couplings

Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.

High Torsional Stiffness. Zero Backlash.

Related Information:


Couplings - K Type
Couplings - K Type


Up to 3600 RPM - Minus 20 to Plus 60o C. 0.34 to 18 Nm.

Strong, flexible polyurethane or Hyrtel(R) is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60o C / Hyrtel(R) : Minus 40 to Plus 100o C. Precision swaged mechanically crimped hubs. Annealed steel hubs.

Related Information:


Shafts - Flexible - Panel Mount - Open
Shafts - Flexible - Panel Mount - Open

Also see combined categories:
All Flexible Panel Mount Shaft

See PDF file at bottom of internet page for Performance Data.

Related Information:


Couplings - Rigid - 1 Piece Clamp - Stainless Steel
Couplings - Rigid - 1 Piece Clamp - Stainless Steel

Also see combined categories:
All Rigid Couplings

303 Grade Stainless

Precision Machined. High torsional load. Non marring, easy to install and adjust. Use on hardened shafts, rigid clamp type design, easily machinable. Available with stepped bores and keyways on 5 week delivery.


Couplings - Rigid - 2 Piece Clamp - Steel
Couplings - Rigid - 2 Piece Clamp - Steel

Also see combined categories:
All Rigid Couplings

12L14 Steel

Precision Machined. High torsional load. Non marring, easy to install and adjust. Assemble without moving shafts. Use on hardened shafts, rigid clamp type design, easily machinable. Black finish with alloy steel cap screws. Available with stepped bores and keyways on 5 week delivery.


Couplings - Spider Type C - Complete
Couplings - Spider Type C - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.

Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application. Polyurethane spider.

Related Information:


Couplings - Slit Type - 4 Slit Miniature - Set Screw Type - Aluminium
Couplings - Slit Type - 4 Slit Miniature - Set Screw Type - Aluminium

Also see combined categories:
All Helical and Slit Couplings

Aluminium - Flexible.



Shafting - Pre Drilled and Tapped - Stainless Steel Steel
Shafting - Pre Drilled and Tapped - Stainless Steel Steel

Also see combined categories:
All Shafting
All Stainless Shafting

For use with rail supports and open linear bearings



Shafting - Pre Drilled and Tapped - High Carbon Steel
Shafting - Pre Drilled and Tapped - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

For use with rail supports and open linear bearings

Straightness: 0.1 mm / mtr.


Shafts - Flexible - Panel Mount - Cased
Shafts - Flexible - Panel Mount - Cased

Also see combined categories:
All Flexible Panel Mount Shaft

See PDF file at bottom of internet page for Performance Data.

Related Information:


Couplings - Rigid - 1 Piece Clamp - Steel
Couplings - Rigid - 1 Piece Clamp - Steel


12L14 Steel



Couplings - Rigid - Set Screw
Couplings - Rigid - Set Screw

Also see combined categories:
All Rigid Couplings

0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.

Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000.

Related Information:


Couplings - Rigid - Hobby - Brass
Couplings - Rigid - Hobby - Brass

Also see combined categories:
All Rigid Couplings

A selection of inexpensive brass couplings for shaft sizes from 2 to 5 mm.


Related Information:


Couplings - Eccentric Drive
Couplings - Eccentric Drive


1.88mm bore press fits most standard hobby motors (2mm shaft)



Push On Retaining Rings - Carbon Steel
Push On Retaining Rings - Carbon Steel

Also see combined categories:
All Push On Rings

M1465 / DTX / Seeger ZA and KS.

Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested.


Couplings - Bellows - Set Screw - 316 Stainless
Couplings - Bellows - Set Screw - 316 Stainless

Also see combined categories:
All Bellows Couplings

Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics

Stainless Steel 303L Bellows. Stainless Steel 316 Hubs.

Related Information:


Couplings - Double Disk - Aluminium
Couplings - Double Disk - Aluminium


Zero Backlash - High Torsional Stiffness.

Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.

Related Information:


Spacers - Hex - Threaded - Steel
Spacers - Hex - Threaded - Steel

Also see combined categories:
All Threaded Hex Spacers

Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.



Bearings - Linear - Sliding - Stainless - PTFE - Open
Bearings - Linear - Sliding - Stainless - PTFE - Open

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.


Collars - Shaft - Hinged - Steel
Collars - Shaft - Hinged - Steel

Also see combined categories:
All Round Bore Shaft Collars
All Hinged Shaft Collars

Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)

Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.

Related Information:


Spacers - Hex - Threaded - 316 Stainless Steel
Spacers - Hex - Threaded - 316 Stainless Steel

Also see combined categories:
All Threaded Hex Spacers

Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.



Latching Handles - Outside Door - Heavy Duty
Latching Handles - Outside Door - Heavy Duty


Black Glass Filled Polyamide Bezel, catch and Plug. Brass Shaft. Zinc plated mild steel fixing.


Collars - Shaft - Hinged - Stainless Steel
Collars - Shaft - Hinged - Stainless Steel

Also see combined categories:
All Round Bore Shaft Collars
All Hinged Shaft Collars

Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel

Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.

Related Information:


Bearings - Linear - Ball - Thomson Precision Steel - Closed
Bearings - Linear - Ball - Thomson Precision Steel - Closed

Also see combined categories:
All Thomson Linear Ball Bearings

For running on shafts fixed at the ends.


Related Information:


Spacers - Hex - Threaded - 303-304 Stainless Steel
Spacers - Hex - Threaded - 303-304 Stainless Steel

Also see combined categories:
All Threaded Hex Spacers

Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.



Bearings - Linear - Ball - Stainless Steel - Closed
Bearings - Linear - Ball - Stainless Steel - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Related Information:


Couplings - Oldham - Hubs - Clamp Style
Couplings - Oldham - Hubs - Clamp Style

Also see combined categories:
All Insert and Jaw Type Couplings
All Oldham Hubs

0.06 to 44 Nm. Max Speed: 3000 RPM.

Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:


Shaftloc-tm Sleeves - Single Ended
Shaftloc-tm Sleeves - Single Ended

Also see combined categories:
All Shaftloc

Simple effective way to lock components onto shafts.

416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened.

Related Information:


Couplings - Oldham - Disks for Clamp Style
Couplings - Oldham - Disks for Clamp Style

Also see combined categories:
All Insert and Jaw Type Couplings
All Oldham Disks

0.06 to 44 Nm. Max Speed: 3000 RPM.

Disk inserts. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:


Couplings - Oldham - Complete - Acetal Disk - Set Screw
Couplings - Oldham - Complete - Acetal Disk - Set Screw

Also see combined categories:
All Insert and Jaw Type Couplings

0.06 to 44 Nm. Max Speed: 3000 RPM.

Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 oC to +60 oC. Oldham couplings are designed to transfer torque between two parallel, but not colinear, shafts. They have three discs, one coupled to the input, one coupled to the output, and a centre disc that is joined to the first two by tongue and grooves. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:


Bearings - Thrust - Ball - Flat - Chrome Steel
Bearings - Thrust - Ball - Flat - Chrome Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:


Bearings - Thrust - Ball - Flat - Stainless Steel
Bearings - Thrust - Ball - Flat - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:


Bearings - Thrust - Ball - Grooved - Chrome Steel
Bearings - Thrust - Ball - Grooved - Chrome Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:


Bearings - Thrust - Ball - Grooved - Stainless Steel
Bearings - Thrust - Ball - Grooved - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:


Gearboxes - Tee - 100.0 x 100.0 x 60.0mm
Gearboxes - Tee - 100.0 x 100.0 x 60.0mm

Also see combined categories:
All Tee Gearboxes

BLHT50 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 125.0 x 125.0 x 80.0mm
Gearboxes - Tee - 125.0 x 125.0 x 80.0mm

Also see combined categories:
All Tee Gearboxes

BLHT60 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 140.0 x 140.0 x 98.0mm
Gearboxes - Tee - 140.0 x 140.0 x 98.0mm

Also see combined categories:
All Tee Gearboxes

BLHT70 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 55.0 x 55.0 x 34.0mm
Gearboxes - Tee -  55.0 x  55.0 x 34.0mm

Also see combined categories:
All Tee Gearboxes

BLHT30 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 75.0 x 75.0 x 44.0mm
Gearboxes - Tee -  75.0 x  75.0 x 44.0mm

Also see combined categories:
All Tee Gearboxes

BLHT40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 40.0 x 40.0 x 25.0mm
Gearboxes - Tee -  40.0 x  40.0 x 25.0mm

Also see combined categories:
All Tee Gearboxes

BLHT20 Series. Miniature gearbox.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Shafting - Ground - Precision - High Carbon Steel
Shafting - Ground - Precision - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.


Related Information:


Gearboxes - Tee - 100.0 x 75.0 x 44.0mm
Gearboxes - Tee - 100.0 x  75.0 x  44.0mm

Also see combined categories:
All Tee Gearboxes

Bevel Gears - 3.0 to 10.3 Nm. BLHM40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 135.0 x 100.0 x 60.0mm
Gearboxes - Tee - 135.0 x 100.0 x  60.0mm

Also see combined categories:
All Tee Gearboxes

Bevel Gears - 7.7 to 30.0 Nm. BLHM50 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 170.0 x 125.0 x 80.0mm
Gearboxes - Tee - 170.0 x 125.0 x  80.0mm

Also see combined categories:
All Tee Gearboxes

Bevel Gears - 19.0 to 70.0 Nm. BLHM60 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 180.0 x 140.0 x 98.0mm
Gearboxes - Tee - 180.0 x 140.0 x  98.0mm

Also see combined categories:
All Tee Gearboxes

Bevel Gears - 26.0 to 128.0 Nm. BLHM70 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 55.0 x 40.0 x 25.0mm
Gearboxes - Tee -  55.0 x  40.0 x  25.0mm

Also see combined categories:
All Tee Gearboxes

Bevel Gears - 0.53 to 1.77 Nm. BLHM20 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Gearboxes - Tee - 74.0 x 55.0 x 34.0mm
Gearboxes - Tee -  74.0 x  55.0 x  34.0mm

Also see combined categories:
All Tee Gearboxes

Bevel Gears - 1.32 to 4.40 Nm. BLHM30 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.


Shafting - Carbon Steel - Keyed
Shafting - Carbon Steel - Keyed

Also see combined categories:
All Shafting
All Steel Shafting

Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.

Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124370 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124370 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.