Shafting Precision Ground
For use with rail supports and open linear bearings
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc. This category may be available in the new MBA online store at
Rod - Drill Blanks.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for A-2 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - A-2 Air Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for O-1 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - O-1 Oil Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for S-7 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - S-7 Air Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for W-1 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - Silversteel - W-1 Water Hardening.
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design. This category may be available in the new MBA online store at
Shafts - Idler.
Related Information:
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
With drilled and counterbored holes for mounting. Neoprene bonded to steel plate.
With drilled and counterbored holes for mounting. Neoprene only, no steel plate.
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at
Shafting - Aluminium - Ceramic Coated - Tapped.
Related Information:
With drilled and counterbored holes for mounting. Urethane bonded to steel plate.
Extended poles can be lightly machined. With tapped blind hole in base for mounting. Insulated aluminium casing.
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting.
Related Information:
Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
Related Information:
Titanium shafting available in oversized and undersized tolerances
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. Shaft with undersized tolerances is suitable for use with precision ground bearings with inner rings. HRB 74. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
This category may be available in the new MBA online store at
Shafts - Pinion.
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium. This category may be available in the new MBA online store at
Rail Supports - Without Shaft.
Related Information:
Includes linear shafting.
Includes shaft to h6 tolerances. Support is made from aluminium. This category may be available in the new MBA online store at
Rail Supports - With Shaft.
Related Information:
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel. This category may be available in the new MBA online store at
Supports - Pedestal Two Bolt.
Related Information:
Zinc chromate fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments. This category may be available in the new MBA online store at
Rail Supports - With Shaft - One Piece.
Related Information:
Zinc chromate. Fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.
Extended poles can be lightly machined. Press fit. Insulated aluminium casing.
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Low cost, light weight, high energy material
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at
Shafting - Aluminium - Ceramic Coated.
Related Information:
Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.
Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.
Non threaded press fit fastener that doesn't require a reamed hole as do dowel pins.Commonly used in place of taper pins.
An economic method of fastening without the need for precision drilled and reamed holes. Recommended hole tolerance is H11. Total length may be slightly longer than the nominal length. Expanded portion of the pin is compressed into the hole a few thousands of an inch wider than the nominal pin diameter. Radial forces lock the pin securely into the drilled hole. This category may be available in the new MBA online store at
Pins - Groove.
Related Information:
Flexible shafting with coupling ends ready to attach to a fixed shaft.
1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm. This category may be available in the new MBA online store at
Shafts - Flexible - Coupling Ends - Open - Mild Steel.
Related Information:
Used to maintain radial integrity and eliminate the need for parallel shafting.
Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads. This category may be available in the new MBA online store at
Housings - Linear - Square.
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges. This category may be available in the new MBA online store at
Bungs and Caps - Reversible - Round.
Related Information:
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Designed to guide, position, and support the cutting tool in a metalworking jig.
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.