Shafting Linear Square Categories
Square Shaft
Shafting - Linear - Square
This category may be available in the new MBA online store at Shafting - Linear - Square.
Linear Bearings with Housing
Housings - Linear - Square
Used to maintain radial integrity and eliminate the need for parallel shafting.
Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads. This category may be available in the new MBA online store at Housings - Linear - Square.
You may also be interested in
Shafting Aluminium
Shafting - Aluminium - Ceramic Coated - Standard
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at Shafting - Aluminium - Ceramic Coated - Standard.
Related Information:
Shafting - Aluminium - Ceramic Coated - Tapped
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at Shafting - Aluminium - Ceramic Coated - Tapped.
Related Information:
Shafting Precision Ground
Supports - Pedestal Two Bolt
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel. This category may be available in the new MBA online store at Supports - Pedestal Two Bolt.
Related Information:
Rail Supports - Without Shaft
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium. This category may be available in the new MBA online store at Rail Supports - Without Shaft.
Related Information:
Rail Supports - With Shaft - Standard
Includes linear shafting.
Includes shaft to h6 tolerances. Support is made from aluminium. This category may be available in the new MBA online store at Rail Supports - With Shaft - Standard.
Related Information:
Shafting - Pre Drilled and Tapped - Stainless Steel
For use with rail supports and open linear bearings
This category may be available in the new MBA online store at Shafting - Pre Drilled and Tapped - Stainless Steel.
Rail Supports - With Shaft - One Piece
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments. This category may be available in the new MBA online store at Rail Supports - With Shaft - One Piece.
Related Information:
Linear Bearing Housings
Housings - Linear Clamps - Square
This category may be available in the new MBA online store at Housings - Linear Clamps - Square.
Linear Slides
Linear Slide Assemblies - Plain - Low Profile - High Load
High capacity, square gib slides are ideal for precision machine tool applications.
The square gib design offers high load capacity and accuracy and withstands force in any direction. Gib is adjustable. Straight line accuracy 0.00254mm. Base is fabricated from A2 tool steel and hardened to Rc58-62. Saddle or riding portion of the slide is fabricated from low carbon steel and can be drilled, tapped and milled for mounting purposes. All slides feature Rulon bearing material for low friction. Stick-slip is virtually non existent as friction at startup and low speeds is virtually eliminated. No lubrication required. Rulon is practically inert to acids, bases and solvents making these slides a good choice for contaminated environments. Temp range minus 240 oC to +300 Deg C.
Linear Bearings
Bearings - Linear Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear Ball - Stainless Steel - Closed.
Related Information:
Bearings - Linear Sliding - Frelon Gold Lined - Closed - Precision
Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.
Related Information:
Bearings - Linear Sliding - Frelon Gold Lined - Open - Precision
Also see combined categories:
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.
Related Information:
Bearings - Linear Sliding - Frelon Gold Lined - Closed - Standard
Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Standard type has slightly larger running clearances.
Related Information:
Bearings - Linear Sliding - Frelon Gold Lined - Open - Standard
Also see combined categories:
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Standard type has slightly larger running clearances.
Related Information:
Bearings - Linear Sliding - Stainless - PTFE - Closed
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000. This category may be available in the new MBA online store at Bearings - Linear Sliding - Stainless - PTFE - Closed.
Bearings - Linear Sliding - Stainless - PTFE - Open
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000. This category may be available in the new MBA online store at Bearings - Linear Sliding - Stainless - PTFE - Open.
Shafting - Carbon Steel - Keyed
Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.
Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.
Shafting - Ground - Precision - Chrome Plated
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance. This category may be available in the new MBA online store at Shafting - Ground - Precision - Chrome Plated.
Shafting - Ground - Precision - High Carbon Steel
Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - High Carbon Steel.
Related Information:
Shafting - Ground - Precision - Stainless 303 Grade
Precision ground shafting.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 303 Grade.
Related Information:
Shafting - Ground - Precision - Stainless 420 Grade Hardened
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 420 Grade Hardened.
Related Information:
Shafting - Ground - Precision - Stainless 440C Grade Hardened
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 440C Grade Hardened.
Related Information:
Shafting - Ground - Precision - Titanium - High Strength
Titanium shafting available in oversized and undersized tolerances
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1
CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. Shaft with undersized tolerances is suitable for use with precision ground bearings with inner rings. HRB 74. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
Shafts - Idler
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design. This category may be available in the new MBA online store at Shafts - Idler.
Related Information:
Rod - Drill Blanks
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc. This category may be available in the new MBA online store at Rod - Drill Blanks.
Shafts - Flexible - Panel Mount - Cased
This category may be available in the new MBA online store at Shafts - Flexible - Panel Mount - Cased.
Shafts - Flexible - Panel Mount - Open
This category may be available in the new MBA online store at Shafts - Flexible - Panel Mount - Open.
Rod - Drill - A-2 Air Hardening
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for A-2 hardening requirements. This category may be available in the new MBA online store at Rod - Drill - A-2 Air Hardening.
Rod - Drill - O-1 Oil Hardening
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for O-1 hardening requirements. This category may be available in the new MBA online store at Rod - Drill - O-1 Oil Hardening.
Rod - Drill - S-7 Air Hardening
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for S-7 hardening requirements. This category may be available in the new MBA online store at Rod - Drill - S-7 Air Hardening.
Rod - Drill - Silversteel - W-1 Water Hardening
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for W-1 hardening requirements. This category may be available in the new MBA online store at Rod - Drill - Silversteel - W-1 Water Hardening.
Shafts - Flexible - Coupling Ends - Open - Mild Steel
Flexible shafting with coupling ends ready to attach to a fixed shaft.
1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm. This category may be available in the new MBA online store at Shafts - Flexible - Coupling Ends - Open - Mild Steel.
Related Information:
Bungs and Caps - Reversible - Round
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges. This category may be available in the new MBA online store at Bungs and Caps - Reversible - Round.
Related Information:
Linear Ball Splines - Shaft
Use with either flanged or unflanged Linear Ball Spline Bearings.
This category may be available in the new MBA online store at Linear Ball Splines - Shaft.
Related Information:
Linear Ball Splines - Bearings - Unflanged
Use with Linear Ball Spline Shaft.
This category may be available in the new MBA online store at Linear Ball Splines - Bearings - Unflanged.
Related Information:
Bearings - Linear Ball - Thomson Precision Steel - Closed
For running on shafts fixed at the ends.
This category may be available in the new MBA online store at Bearings - Linear Ball - Thomson Precision Steel - Closed.
Related Information:
Bearings - Linear Sliding - Frelon J Lined - Closed - Standard
Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon J Lined Linear Bearings
All Closed Frelon Lined Linear Bearings
All Closed Frelon J Lined Linear Bearings
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon J = 10000 PV. Dry Running Max Surface Speed Frelon J = 0.7 mtrs / sec (140 ft / min). With Lubrication Max Surface Speed Frelon J = 2 mtrs / sec (400 ft / min). Standard type has slightly larger running clearances.
Related Information:
Bearings - Linear Ball - Miniature - Super High Precision
High Precision Corrosion Resistant Miniature Linear Bearings.
High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.
Related Information:
Bearings - Linear Sliding - Ceramic Coated
Approved for direct food contact in applications where animal fat or food approved lubricants are present.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Minimum shaft hardness RC35. Max PV 40,000. Temperature range -125 oC to +226 Deg C. Max static PSI 5000. This category may be available in the new MBA online store at Bearings - Linear Sliding - Ceramic Coated.
Housings - Linear - Pillow Block - Closed - Ceramic Coated
Approved for direct food contact in applications where animal fat or food approved lubricants are present.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. DO NOT USE WD-40 or Silcone based spray lubricants. This category may be available in the new MBA online store at Housings - Linear - Pillow Block - Closed - Ceramic Coated.
Linear - Assemblies - Ball Slide - Precision
These precision ball slides have a typical coefficient of friction of 0.003 and provide straight line accuracy of 0.0005mm per mm of travel.
At load capacity a life of 250 million mm of travel can be expected. The expected life at half load capacity is 2.5 billion mm. Factory preload adjustment prevents sideplay and backlash. Lightweight aluminium carriage and base with high load capacity. Four tapped and threaded carriage holes and counterbored base holes simplify installation and component mounting. Long life, self cleaning ball bearing needs no lubrication. Positional repeatability 0.005mm. Clear anodised finish.
Linear Guide System - Two Piece
Using Frelon Gold plain bearing technology. Rail and carriage are made from 6063-T6 aluminium and come as a set.
Rails are ceramic coated to resist corrosion and repel weld spatter and contaminants. Smooth running. Dampens vibration. Guide has slots for T nuts or bolts. Two component system allows for easier installation than traditional rail systems. This category may be available in the new MBA online store at Linear Guide System - Two Piece.
Linear - Mini Rail Carriages - Self-Lubricating
Carriages for the Mini-Rail system. Match by rail width. Rail sold separately.
Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments. This category may be available in the new MBA online store at Linear - Mini Rail Carriages - Self-Lubricating.
Related Information:
Linear - Mini Rail - Self-Lubricating
Rail Only. Carriages sold separately - match by rail width.
Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments. This category may be available in the new MBA online store at Linear - Mini Rail - Self-Lubricating.
Related Information:
Linear Slide Assemblies - Cross Roller
Higher load capacity than precision ball slide assemblies. High cycling rates. Tolerant of shock and overhanging loads.
Accuracy of 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm. Not as naturally cleaning as ball slides. A good choice for environments protected from dust, and when heavy loads are a consideration. Positive stops prevent over-travel. Rollers improve capacity 8-10 times that of balls. Alternately crossed rollers handle force in any direction. Lightweight aluminium carriage and base. Interchangeable with many types of ball slides. Four tapped carriage holes and two counter bored base holes simplify installation and component mounting. This category may be available in the new MBA online store at Linear Slide Assemblies - Cross Roller.
Linear Slides - Cross Roller Tables - Aluminium
Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.
Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings. This category may be available in the new MBA online store at Linear Slides - Cross Roller Tables - Aluminium.
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153564 products in 2095 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
