Shafting Precision Ground
Titanium shafting available in oversized and undersized tolerances
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. Shaft with undersized tolerances is suitable for use with precision ground bearings with inner rings. HRB 74. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting.
Related Information:
Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
Related Information:
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design. This category may be available in the new MBA online store at
Shafts - Idler.
Related Information:
This category may be available in the new MBA online store at
Shafts - Pinion.
For use with rail supports and open linear bearings
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium. This category may be available in the new MBA online store at
Rail Supports - Without Shaft.
Related Information:
Includes linear shafting.
Includes shaft to h6 tolerances. Support is made from aluminium. This category may be available in the new MBA online store at
Rail Supports - With Shaft.
Related Information:
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel. This category may be available in the new MBA online store at
Supports - Pedestal Two Bolt.
Related Information:
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments. This category may be available in the new MBA online store at
Rail Supports - With Shaft - One Piece.
Related Information:
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc. This category may be available in the new MBA online store at
Rod - Drill Blanks.
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100
oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at
Bearings - Linear - Ball - Stainless Steel - Closed.
Related Information:
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.
Related Information:
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.
Related Information:
Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. Threaded either 1-72 UNF or M1.2.
Related Information:
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at
Shafting - Aluminium - Ceramic Coated.
Related Information:
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at
Shafting - Aluminium - Ceramic Coated - Tapped.
Related Information:
Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.
Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.
Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Includes miniature precision types. Carbon steel.
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at
Collars - Shaft - Standard - Steel.
Related Information:
Includes miniature precision types. 303 and 316 Types.
Related Information:
Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127
Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127
For running on shafts fixed at the ends.
Related Information:
High Precision Corrosion Resistant Miniature Linear Bearings.
High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.
Related Information:
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for A-2 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - A-2 Air Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for O-1 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - O-1 Oil Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for S-7 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - S-7 Air Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for W-1 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - Silversteel - W-1 Water Hardening.
Flexible shafting with coupling ends ready to attach to a fixed shaft.
1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm. This category may be available in the new MBA online store at
Shafts - Flexible - Coupling Ends - Open - Mild Steel.
Related Information:
Use with NEMA Size 17 Motors.
Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).
Related Information:
Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm
2. Yield Strength 77.5kgf / mm
2. Elongation 10 Percent. This category may be available in the new MBA online store at
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI.
Related Information:
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges. This category may be available in the new MBA online store at
Bungs and Caps - Reversible - Round.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Flat washers. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at
Washers - Flat - Titanium - CP Grade 1.
Related Information:
Used to maintain radial integrity and eliminate the need for parallel shafting.
Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads. This category may be available in the new MBA online store at
Housings - Linear - Square.
303 Grade Stainless
Precision Machined. High torsional load. Non marring, easy to install and adjust. Use on hardened shafts, rigid clamp type design, easily machinable. Available with stepped bores and keyways on 5 week delivery.
For general hobby applications. This rod is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths for general hobby applications. Not recommended for heavy duty applications. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
12L14 Steel
Precision Machined. High torsional load. Non marring, easy to install and adjust. Assemble without moving shafts. Use on hardened shafts, rigid clamp type design, easily machinable. Black finish with alloy steel cap screws. Available with stepped bores and keyways on 5 week delivery.
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.