Shafting Ground Precision Stainless 303 Grade Categories
Shafting Precision Ground
Shafting - Ground - Precision - Stainless 303 Grade
Precision ground shafting.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 303 Grade.
Related Information:
Shafting - Ground - Precision - Stainless 420 Grade Hardened
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 420 Grade Hardened.
Related Information:
Shafting - Ground - Precision - Stainless 440C Grade Hardened
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 440C Grade Hardened.
Related Information:
Shafting - Pre Drilled and Tapped - Stainless Steel
For use with rail supports and open linear bearings
This category may be available in the new MBA online store at Shafting - Pre Drilled and Tapped - Stainless Steel.
Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1
CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. Shaft with undersized tolerances is suitable for use with precision ground bearings with inner rings. HRB 74. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
Shafting - Ground - Precision - Titanium - High Strength
Titanium shafting available in oversized and undersized tolerances
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
You may also be interested in
Pins Dowel
Pins - Dowel - Standard - Chamfered Ends - 303-304 Stainless
Precision Dowel Pins - 303/304 Grade Stainless - Based on DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - Chamfered Ends - 303-304 Stainless.
Related Information:
Pins - Dowel - Standard - Rounded Ends - 303-304 Stainless
Precision Dowel Pins - 303/304 Grade Stainless- Based on DIN7
Rounded end dowel pins are measured from the start of the edge rounding. This allows the pin to completely fill the hole after you grind off the rounded end. Diameter tolerances are m6. Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - Rounded Ends - 303-304 Stainless.
Related Information:
Shafting Precision Ground
Shafting - Ground - Precision - Chrome Plated
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance. This category may be available in the new MBA online store at Shafting - Ground - Precision - Chrome Plated.
Shafting - Ground - Precision - High Carbon Steel
Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - High Carbon Steel.
Related Information:
Couplings Rigid
Couplings - Rigid - 1 Piece Clamp - Stainless Steel
303 Grade Stainless
Precision Machined. High torsional load. Non marring, easy to install and adjust. Use on hardened shafts, rigid clamp type design, easily machinable. Available with stepped bores and keyways on 5 week delivery.
Shafting Precision Ground
Shafts - Idler
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design. This category may be available in the new MBA online store at Shafts - Idler.
Related Information:
Rail Supports - Without Shaft
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium. This category may be available in the new MBA online store at Rail Supports - Without Shaft.
Related Information:
Supports - Pedestal Two Bolt
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel. This category may be available in the new MBA online store at Supports - Pedestal Two Bolt.
Related Information:
Rail Supports - With Shaft - Standard
Includes linear shafting.
Includes shaft to h6 tolerances. Support is made from aluminium. This category may be available in the new MBA online store at Rail Supports - With Shaft - Standard.
Related Information:
Rail Supports - With Shaft - One Piece
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments. This category may be available in the new MBA online store at Rail Supports - With Shaft - One Piece.
Related Information:
Bearings Stainless Special Grades
Bearings - Double Row Ball Semi Precision - 316 Stainless Steel
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. This category may be available in the new MBA online store at Bearings - Double Row Ball Semi Precision - 316 Stainless Steel.
Related Information:
Pins Dowel
Pins - Dowel - Standard - Chamfered Ends - 316 Stainless
Precision Dowel Pins - 316 Grade - Based on DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - Chamfered Ends - 316 Stainless.
Related Information:
Pins - Dowel - Standard - Chamfered Ends - 416 Stainless
Precision Dowel Pins - 416 Grade - Based on DIN6325 or ISO2338
Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - Chamfered Ends - 416 Stainless.
Related Information:
Pins - Dowel - Standard - Rounded Ends - 316 Stainless
Precision Dowel Pins - 316 Grade - Based on DIN7
Diameter tolerances are m6. Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - Rounded Ends - 316 Stainless.
Related Information:
Shim
Shim and Foil - Stainless Steel
Precision stainless shim sheet and strip. From very thin foil to thick sizes. Includes 302, 304 and 430 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes K&S Metals range and more. This category may be available in the new MBA online store at Shim and Foil - Stainless Steel.
Related Information:
Linear Bearings
Bearings - Linear Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear Ball - Stainless Steel - Closed.
Related Information:
Collars
Collars - Shaft - Hinged - Stainless Steel
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Collars - Shaft - Standard - Stainless Steel
Includes miniature precision types. 303 and 316 Types.
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at Collars - Shaft - Standard - Stainless Steel.
Related Information:
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Joints - Swivel - Knob Style - Stainless Steel
Precision made. Column lock feature. Will not become loose when adjusting. Universal design will fit any make of magnetic base, surface gauge or indicator. 303 Stainless Steel.
This category may be available in the new MBA online store at Joints - Swivel - Knob Style - Stainless Steel.
Joints - Swivel - Wing Knob - Stainless Steel
Precision made. Column lock feature. Will not become loose when adjusting. Universal design will fit any make of magnetic base, surface gauge or indicator. 303 Stainless Steel.
This category may be available in the new MBA online store at Joints - Swivel - Wing Knob - Stainless Steel.
Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel
Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.
Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.
Washers - Flat - Stainless Steel - Precision Shim
Precision Tolerances.
This category may be available in the new MBA online store at Washers - Flat - Stainless Steel - Precision Shim.
Related Information:
Screws - Thumb - Knurled - Stainless - Precision Head
This category may be available in the new MBA online store at Screws - Thumb - Knurled - Stainless - Precision Head.
Related Information:
Clamps - Gear - Split
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Shims - Slotted - Imperial Sizes
Precision stainless steel 300 series. Solves alignment and leveling problems on pumps, generators and other machinery. Tabs eliminate need to place hands under machinery. Conform to standard bolt and stud sizes.
This category may be available in the new MBA online store at Shims - Slotted - Imperial Sizes.
Ball Transfer Units - Screw Stem - Stainless - Precision
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Max Load is applicable when used as a transfer, not as a castor. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Stainless - Precision.
Washers - Flat - Stainless Steel 304 - Commercial
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - Stainless Steel 304 - Commercial.
Related Information:
Washers - Flat - Stainless Steel 316 - Commercial
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - Stainless Steel 316 - Commercial.
Related Information:
Bearings - Double Row Ball Semi Precision - Acetal with Stainless Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.
Related Information:
Bearings - Single Row Ball Flanged - High Precision Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges. High precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Single Row Ball Flanged - High Precision Stainless.
Related Information:
Bearings - Single Row Ball Unflanged - High Precision Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings. High precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Single Row Ball Unflanged - High Precision Stainless.
Related Information:
Clamps - Gear - Screw Type
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Pins - Dowel - Stepped - Chamfered Ends - 440 Stainless Steel
Precision Dowel Pins with a Step
This category may be available in the new MBA online store at Pins - Dowel - Stepped - Chamfered Ends - 440 Stainless Steel.
Related Information:
Bearings - Single Row Ball Flanged - Extended Inner High Precision Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Bearings - Single Row Ball Unflanged - Extended Inner High Precision Stainless
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings with extended inner ring (wide inner ring). High precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Pins - Dowel - Stepped - Chamfered Ends - Extractable - 440 Stainless Steel
Precision Extractable Dowel Pins with a Step
Related Information:
Slides - Linear - Clean Room
Stainless Steel throughout (similar to 440C). Speed: 0.5 m/sec (30 m/min). Temperature: +100oC (Continuous), +140oC (Maximum). Life will be less than normal at +100oC and dimensions may change. Lateral Loading: Dynamic x 1.13 C - Static x 1.19 Co. Precision Linear Slide Unit is a compact linear motion rolling guide for limited stroke length.
Collars - Shaft - Clamp Type - Two Piece - 300 Grade Stainless Steel
Includes 303 and 304 Grade Stainless
Related Information:
Gearheads - Inline - Planetary - Size 17 - Precision
Use with NEMA Size 17 Motors.
Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).
Related Information:
Mounts - Anti-Vibration - 303 Stainless Steel
Corrosion resistant designed with high grade nitrile rubber and stainless steel.
Swivel movement plus or minus 7o for stable support on inclined floors. Nitrile rubber base helps ensure stability. This category may be available in the new MBA online store at Mounts - Anti-Vibration - 303 Stainless Steel.
Related Information:
Keysteel Lengths - Square - Stainless Steel
303, 304 and 316 grade key steel. Square stainless steel bar that can be used for keysteel or for small construction projects.
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled. This category may be available in the new MBA online store at Keysteel Lengths - Square - Stainless Steel.
Related Information:
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153564 products in 2094 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
