Small Parts & Bearings - an MBA company

Shafting Ground Precision High Carbon Steel Categories


Shafting Precision Ground


Shafting - Ground - Precision - High Carbon Steel
Shafting - Ground - Precision - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - High Carbon Steel.

Related Information:


Shafting - Pre Drilled and Tapped - Stainless Steel
Shafting - Pre Drilled and Tapped - Stainless Steel

Also see combined categories:
All Shafting
All Stainless Shafting

For use with rail supports and open linear bearings

This category may be available in the new MBA online store at Shafting - Pre Drilled and Tapped - Stainless Steel.


Shafting - Ground - Precision - Titanium - High Strength
Shafting - Ground - Precision - Titanium - High Strength

Also see combined categories:
All Shafting
All Titanium Shafting

Titanium shafting available in oversized and undersized tolerances

Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.

Related Information:


Supports - Pedestal Two Bolt
Supports - Pedestal Two Bolt

Also see combined categories:
All Supports

For linear shafting.

Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel. This category may be available in the new MBA online store at Supports - Pedestal Two Bolt.

Related Information:


Shafting - Ground - Precision - Chrome Plated
Shafting - Ground - Precision - Chrome Plated


Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.

Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance. This category may be available in the new MBA online store at Shafting - Ground - Precision - Chrome Plated.


Shafting - Ground - Precision - Stainless 303 Grade
Shafting - Ground - Precision - Stainless 303 Grade

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 303 Grade.

Related Information:


Shafting - Ground - Precision - Stainless 416 Grade Hardened
Shafting - Ground - Precision - Stainless 416 Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 416 Grade Hardened.

Related Information:


Shafting - Ground - Precision - Stainless 420 Grade Hardened
Shafting - Ground - Precision - Stainless 420 Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 420 Grade Hardened.

Related Information:


Shafting - Ground - Precision - Stainless 440C Grade Hardened
Shafting - Ground - Precision - Stainless 440C Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 440C Grade Hardened.

Related Information:


Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1
Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1

Also see combined categories:
All Shafting
All Titanium Shafting

CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.

Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. Shaft with undersized tolerances is suitable for use with precision ground bearings with inner rings. HRB 74. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.

Related Information:


Shafts - Idler
Shafts - Idler


Ready made precision ground idler shafts.

Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design. This category may be available in the new MBA online store at Shafts - Idler.

Related Information:


Shafts - Pinion
Shafts - Pinion


This category may be available in the new MBA online store at Shafts - Pinion.


Rail Supports - Without Shaft
Rail Supports - Without Shaft

Also see combined categories:
All Shaft Supports

For mounting of linear shafting.

Shafting sold separately. Support is made from aluminium. This category may be available in the new MBA online store at Rail Supports - Without Shaft.

Related Information:


Rail Supports - With Shaft
Rail Supports - With Shaft

Also see combined categories:
All Shaft Supports

Includes linear shafting.

Includes shaft to h6 tolerances. Support is made from aluminium. This category may be available in the new MBA online store at Rail Supports - With Shaft.

Related Information:


You may also be interested in

Linear Slides


Rail Systems - Type 3 - Linear - Precision - Rails - Carbon Steel
Rail Systems - Type 3 - Linear - Precision - Rails - Carbon Steel


Match with carriage by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Rails are subjected to multiple straightening processes during and after grinding of the ball paths to ensure straight and accurate rails. This category may be available in the new MBA online store at Rail Systems - Type 3 - Linear - Precision - Rails - Carbon Steel.

Related Information:


Rail Systems - Type 3 - Linear - Precision - Carriage - Carbon Steel - Narrow
Rail Systems - Type 3 - Linear - Precision - Carriage - Carbon Steel - Narrow


Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination.

Related Information:


Rail Systems - Type 3 -Linear - Precision - Carriage - Carbon Steel - Standard
Rail Systems - Type 3 -Linear - Precision - Carriage - Carbon Steel - Standard


Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination.

Related Information:


Shafting Precision Ground


Rail Supports - With Shaft - One Piece
Rail Supports - With Shaft - One Piece

Also see combined categories:
All Shaft Supports

One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.

Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments. This category may be available in the new MBA online store at Rail Supports - With Shaft - One Piece.

Related Information:


Shafting General Purpose


Rod - Drill Blanks
Rod - Drill Blanks

Also see combined categories:
All Silver Steel Drill Blanks
All Drill Rod

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc. This category may be available in the new MBA online store at Rod - Drill Blanks.


Tooling Balls


Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.

Related Information:


Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.

Related Information:


Washers Flat Metallic


Washers - Flat - Carbon Spring Steel - Precision Shim
Washers - Flat - Carbon Spring Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.

C1010 steel types best suited to arbor shimming. This category may be available in the new MBA online store at Washers - Flat - Carbon Spring Steel - Precision Shim.

Related Information:


Collars


Collars - Shaft - Standard - Steel
Collars - Shaft - Standard - Steel

Also see combined categories:
All Round Bore Shaft Collars
All Standard Shaft Collars

Includes miniature precision types. Carbon steel.

Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at Collars - Shaft - Standard - Steel.

Related Information:


Shafting General Purpose


Shafting - Carbon Steel - Keyed
Shafting - Carbon Steel - Keyed

Also see combined categories:
All Shafting
All Steel Shafting

Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.

Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.


Clamps


Clamps - Gear - Split
Clamps - Gear - Split

Also see combined categories:
All Gear Clamps

Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.

Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.

Related Information:


Clamps - Gear - Screw Type
Clamps - Gear - Screw Type

Also see combined categories:
All Gear Clamps

Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.

Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.

Related Information:


Bearings - Linear - Ball - Stainless Steel - Closed
Bearings - Linear - Ball - Stainless Steel - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear - Ball - Stainless Steel - Closed.

Related Information:


Bearings - Ball - High Precision - 440C Stainless
Bearings - Ball - High Precision - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome

Stainless Steel Bearings - Abec 5 and Abec 7.

Single row radial ball bearings. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - High Precision - 440C Stainless.

Related Information:


Bearings - Ball - Flanged - High Precision - 440C Stainless
Bearings - Ball - Flanged - High Precision - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Flanged Ball Bearings

Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.

Single row radial ball bearings with flanges. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - Flanged - High Precision - 440C Stainless.

Related Information:


Bearings - Ball - WIR - High Precision - 440C Stainless
Bearings - Ball - WIR - High Precision - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Extended Inner Ring Bearings

Stainless Steel Bearings - Abec 5 and Abec 7.

Single row radial ball bearings with extended inner ring (wide inner ring). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - WIR - High Precision - 440C Stainless.

Related Information:


Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless
Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Flanged Ball Bearings with Extended Inner

Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.

Single row radial ball bearings with flanges and extended inner rings (wide inner rings). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless.

Related Information:


Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel
Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit
Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. Knurled shoulder. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit.

Related Information:


Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit
Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. Knurled shoulder. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit.

Related Information:


Balls - Tooling - One Piece - Shoulder - Steel - Press Fit
Balls - Tooling - One Piece - Shoulder - Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. This category may be available in the new MBA online store at Balls - Tooling - One Piece - Shoulder - Steel - Press Fit.

Related Information:


Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit
Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. This category may be available in the new MBA online store at Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit.

Related Information:


Pins - Taper - Metric - Carbon Steel
Pins - Taper - Metric - Carbon Steel

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um

Metric Sizes to DIN 1. This category may be available in the new MBA online store at Pins - Taper - Metric - Carbon Steel.

Related Information:


Couplings - Rigid - 1 Piece Clamp - Stainless Steel
Couplings - Rigid - 1 Piece Clamp - Stainless Steel

Also see combined categories:
All Rigid Couplings

303 Grade Stainless

Precision Machined. High torsional load. Non marring, easy to install and adjust. Use on hardened shafts, rigid clamp type design, easily machinable. Available with stepped bores and keyways on 5 week delivery.


Linear Slide Assemblies - Plain - Low Profile - High Load
Linear Slide Assemblies - Plain - Low Profile - High Load

Also see combined categories:
All Linear Slide Assemblies

High capacity, square gib slides are ideal for precision machine tool applications.

The square gib design offers high load capacity and accuracy and withstands force in any direction. Gib is adjustable. Straight line accuracy 0.00254mm. Base is fabricated from A2 tool steel and hardened to Rc58-62. Saddle or riding portion of the slide is fabricated from low carbon steel and can be drilled, tapped and milled for mounting purposes. All slides feature Rulon bearing material for low friction. Stick-slip is virtually non existent as friction at startup and low speeds is virtually eliminated. No lubrication required. Rulon is practically inert to acids, bases and solvents making these slides a good choice for contaminated environments. Temp range minus 240 oC to +300 Deg C.


Bearings - Linear - Frelon Gold Lined - Closed - Precision
Bearings - Linear - Frelon Gold Lined - Closed - Precision

Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.

Related Information:


Bearings - Linear - Frelon Gold Lined - Open - Precision
Bearings - Linear - Frelon Gold Lined - Open - Precision

Also see combined categories:
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.

Related Information:


Couplings - Rigid - 2 Piece Clamp - Steel
Couplings - Rigid - 2 Piece Clamp - Steel

Also see combined categories:
All Rigid Couplings

12L14 Steel

Precision Machined. High torsional load. Non marring, easy to install and adjust. Assemble without moving shafts. Use on hardened shafts, rigid clamp type design, easily machinable. Black finish with alloy steel cap screws. Available with stepped bores and keyways on 5 week delivery.


Slides - Linear - Cross Roller Rail
Slides - Linear - Cross Roller Rail

Also see combined categories:
All Linear Slides

Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.

Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds. This category may be available in the new MBA online store at Slides - Linear - Cross Roller Rail.


Tools - Taps - High Speed Steel - Spiral Point
Tools - Taps - High Speed Steel - Spiral Point

Also see combined categories:
All Taps
All Tools

Metric intermediate ground thread high speed steel taps. Also called gun taps.

This category may be available in the new MBA online store at Tools - Taps - High Speed Steel - Spiral Point.


Feeler Gauge Stock - C1095 Carbon Steel
Feeler Gauge Stock - C1095 Carbon Steel


Used for close spacing and extremely tight tolerance situation.

Rc48-62 hardness. High carbon steel. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.


Linear Slides - Cross Roller Tables - Steel
Linear Slides - Cross Roller Tables - Steel

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings. This category may be available in the new MBA online store at Linear Slides - Cross Roller Tables - Steel.


Collars - Shaft - Hinged - Steel
Collars - Shaft - Hinged - Steel

Also see combined categories:
All Round Bore Shaft Collars
All Hinged Shaft Collars

Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)

Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.

Related Information:


Bearings - Linear - Ball - Thomson Precision Steel - Closed
Bearings - Linear - Ball - Thomson Precision Steel - Closed

Also see combined categories:
All Thomson Linear Ball Bearings

For running on shafts fixed at the ends.

This category may be available in the new MBA online store at Bearings - Linear - Ball - Thomson Precision Steel - Closed.

Related Information:


Collars - Shaft - Hinged - Stainless Steel
Collars - Shaft - Hinged - Stainless Steel

Also see combined categories:
All Round Bore Shaft Collars
All Hinged Shaft Collars

Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel

Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.

Related Information:


Shim - Tin
Shim - Tin

Also see combined categories:
All Shim
All Sheet

Precision steel shim sheet. Very thin to thick sizes.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes K&S Metals range and more. This category may be available in the new MBA online store at Shim - Tin.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138615 products in 2015 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138615 products in 2015 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.