Small Parts & Bearings - an MBA company

Shafting Carbon Steel Keyed Categories


Shafting General Purpose


Shafting - Carbon Steel - Keyed
Shafting - Carbon Steel - Keyed

Also see combined categories:
All Shafting
All Steel Shafting

Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.

Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.


You may also be interested in

Shafting Precision Ground


Shafting - Ground - Precision - High Carbon Steel
Shafting - Ground - Precision - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - High Carbon Steel.

Related Information:


Shafting - Pre Drilled and Tapped - Stainless Steel
Shafting - Pre Drilled and Tapped - Stainless Steel

Also see combined categories:
All Shafting
All Stainless Shafting

For use with rail supports and open linear bearings

This category may be available in the new MBA online store at Shafting - Pre Drilled and Tapped - Stainless Steel.


Shafting General Purpose


Rod - Drill Blanks
Rod - Drill Blanks

Also see combined categories:
All Silver Steel Drill Blanks
All Drill Rod

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc. This category may be available in the new MBA online store at Rod - Drill Blanks.


Flexible Shaft


Shafts - Flexible - Coupling Ends - Open - Mild Steel
Shafts - Flexible - Coupling Ends - Open - Mild Steel

Also see combined categories:
All Coupling End Flexible Shaft

Flexible shafting with coupling ends ready to attach to a fixed shaft.

1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm. This category may be available in the new MBA online store at Shafts - Flexible - Coupling Ends - Open - Mild Steel.

Related Information:


Shafting Precision Ground


Supports - Pedestal Two Bolt
Supports - Pedestal Two Bolt

Also see combined categories:
All Supports

For linear shafting.

Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel. This category may be available in the new MBA online store at Supports - Pedestal Two Bolt.

Related Information:


Keys - Machine - Carbon Steel
Keys - Machine - Carbon Steel

Also see combined categories:
All Machine Keys

Form A has rounded ends. Form B has square ends. Form AB has one end rounded and one end square. DIN6885

This category may be available in the new MBA online store at Keys - Machine - Carbon Steel.

Related Information:


Keysteel Lengths - Rectangular - Carbon Steel
Keysteel Lengths - Rectangular - Carbon Steel

Also see combined categories:
All Keysteel Lengths

Plain carbon steel key steel. Rectangular steel bar that can be used for keysteel or for small construction projects.

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled. This category may be available in the new MBA online store at Keysteel Lengths - Rectangular - Carbon Steel.

Related Information:


Keysteel Lengths - Square - Carbon Steel
Keysteel Lengths - Square - Carbon Steel

Also see combined categories:
All Keysteel Lengths

Plain carbon steel key steel. Square steel bar that can be used for keysteel or for small construction projects.

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled. This category may be available in the new MBA online store at Keysteel Lengths - Square - Carbon Steel.

Related Information:


Sprockets - 9.53 x 4.7mm - Simplex - Carbon Steel - Plain Bore
Sprockets -  9.53 x 4.7mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 9.53x4.7mm steel chain (35-1 ASA)

Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch. This category may be available in the new MBA online store at Sprockets - 9.53 x 4.7mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Pins - Clik - Carbon Steel
Pins - Clik - Carbon Steel

Also see combined categories:
All Clik Lynch Pins

Self locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Also known as a lynch pin.

Pin is made from carbon steel and heat treated to RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated. This category may be available in the new MBA online store at Pins - Clik - Carbon Steel.

Related Information:


Pins - Roll - Carbon Steel
Pins - Roll - Carbon Steel

Also see combined categories:
All Roll Pins

Plain carbon spring steel DIN1481/ISO8752.

Also known as sel-lok and bissell pins. This category may be available in the new MBA online store at Pins - Roll - Carbon Steel.

Related Information:


Hexagonal Bar - Carbon Steel
Hexagonal Bar - Carbon Steel

Also see combined categories:
All Metal Bar - Hexagonal

Saw Cut Ends. Small A/F sizes may not be perfectly straight. This category may be available in the new MBA online store at Hexagonal Bar - Carbon Steel.


Tools - Dies - Carbon Steel
Tools - Dies - Carbon Steel

Also see combined categories:
All Dies
All Tools

Tungsten Chrome Alloy - Carbon Steel Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.

This category may be available in the new MBA online store at Tools - Dies - Carbon Steel.


Tools - Taps - Carbon Steel - Hand
Tools - Taps - Carbon Steel - Hand

Also see combined categories:
All Taps
All Tools

Carbon Steel Straight Flute Taps. Starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.

Carbon steel hand taps. Carbon Steel (CS) Hand taps. This category may be available in the new MBA online store at Tools - Taps - Carbon Steel - Hand.


Push On Retaining Rings - Carbon Steel
Push On Retaining Rings - Carbon Steel

Also see combined categories:
All Push On Rings

M1465 / DTX / Seeger ZA and KS.

Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested. This category may be available in the new MBA online store at Push On Retaining Rings - Carbon Steel.


Washers - Flat - Carbon Spring Steel - Precision Shim
Washers - Flat - Carbon Spring Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.

C1010 steel types best suited to arbor shimming. This category may be available in the new MBA online store at Washers - Flat - Carbon Spring Steel - Precision Shim.

Related Information:


Collars - Shaft - Standard - Steel
Collars - Shaft - Standard - Steel

Also see combined categories:
All Round Bore Shaft Collars
All Standard Shaft Collars

Includes miniature precision types. Carbon steel.

Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at Collars - Shaft - Standard - Steel.

Related Information:


Circlips - External - Standard - Carbon Steel
Circlips - External - Standard - Carbon Steel

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).

Plain carbon steel. This category may be available in the new MBA online store at Circlips - External - Standard - Carbon Steel.

Related Information:


Circlips - Internal - Standard - Carbon Steel
Circlips - Internal - Standard - Carbon Steel

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Plain carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Carbon Steel.

Related Information:


E-Clips - Basic - Carbon Steel
E-Clips - Basic - Carbon Steel

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Carbon spring steel including zinc plated and plain.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip. Includes plain and zinc plated. This category may be available in the new MBA online store at E-Clips - Basic - Carbon Steel.

Related Information:


Pins - Clevis - Low Carbon Steel - Pin Locking
Pins - Clevis - Low Carbon Steel - Pin Locking

Also see combined categories:
All Clevis Pins

Match with a suitable R-Clip or Spilt Pin - pin size shown in listings

In addition to retaining parts on a shaft or axle, clevis pins can also be used as light duty axles, spring holders or even fishing line weights. Made from low carbon steel. This category may be available in the new MBA online store at Pins - Clevis - Low Carbon Steel - Pin Locking.

Related Information:


Pins - Dowel - Extractable - Carbon Steel
Pins - Dowel - Extractable - Carbon Steel

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6. Din 7979.

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.

Related Information:


Pins - Dowel - Standard - Carbon Steel - Chamfered Ends
Pins - Dowel - Standard - Carbon Steel - Chamfered Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - Based on DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - Carbon Steel - Chamfered Ends.

Related Information:


Pins - Dowel - Stepped - Carbon Steel - Chamfered Ends
Pins - Dowel - Stepped - Carbon Steel - Chamfered Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins with a Step

This category may be available in the new MBA online store at Pins - Dowel - Stepped - Carbon Steel - Chamfered Ends.

Related Information:


Pins - Taper - Metric - Carbon Steel
Pins - Taper - Metric - Carbon Steel

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um

Metric Sizes to DIN 1. This category may be available in the new MBA online store at Pins - Taper - Metric - Carbon Steel.

Related Information:


Sleeves - Hex Hole - Carbon Steel
Sleeves - Hex Hole - Carbon Steel

Also see combined categories:
All Hex Hole Sleeves

Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.

This category may be available in the new MBA online store at Sleeves - Hex Hole - Carbon Steel.


Washers - Disc Spring - Carbon Steel
Washers - Disc Spring - Carbon Steel

Also see combined categories:
All Disc Springs

Includes disc springs to DIN 2093.

Manufactured under strict quality control to conform to DIN 2093. This category may be available in the new MBA online store at Washers - Disc Spring - Carbon Steel.


Washers - Spring - Curved - Carbon Steel
Washers - Spring - Curved - Carbon Steel

Also see combined categories:
All Wave Washers

Wave Washers - All Materials.

ID and OD are long axis dimensions. This category may be available in the new MBA online store at Washers - Spring - Curved - Carbon Steel.


Hooks - S - Steel
Hooks - S - Steel

Also see combined categories:
All S Hooks

Low carbon cold drawn steel with zinc plated finish

Any deviations such as angular lifts, shock loads, modifications will result in drastically reduced maximum loads. This category may be available in the new MBA online store at Hooks - S - Steel.


Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm duplex chain (08B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. This category may be available in the new MBA online store at Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore.

Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. This category may be available in the new MBA online store at Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Sprockets - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.85mm simplex chain (40-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. American Standard 40-1 - 1/2 inch. With and without hubs. This category may be available in the new MBA online store at Sprockets - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Sprockets - 9.53 x 5.7mm - Simplex - Carbon Steel - Plain Bore
Sprockets -  9.53 x 5.7mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 9.53x5.7mm steel chain (06B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch. This category may be available in the new MBA online store at Sprockets - 9.53 x 5.7mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 15.90x9.65mm duplex steel chain (10B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch. This category may be available in the new MBA online store at Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.

Related Information:


Sprocket Plates - 9.53 x 5.7mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates -  9.53 x 5.7mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 9.53x5.7mm steel chain (06B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch.

Related Information:


Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.85mm simplex chain (40-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.

Related Information:


Sprocket Plates - 19.05 x 11.68mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 19.05 x 11.68mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 19.05x11.68mm simplex steel chain (12B-1 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 12B - 3/4 inch.

Related Information:


Keys - Woodruff - Plain
Keys - Woodruff - Plain

Also see combined categories:
All Woodruff Keys

Plain carbon steel

This category may be available in the new MBA online store at Keys - Woodruff - Plain.

Related Information:


Push In Retaining Rings - Carbon Steel
Push In Retaining Rings - Carbon Steel


Thrust load shown is calculated for ideal conditions with mild steel bore. This category may be available in the new MBA online store at Push In Retaining Rings - Carbon Steel.


Attachments - Wire Rope Clips - Carbon Steel
Attachments - Wire Rope Clips - Carbon Steel

Also see combined categories:
All Wire Rope Clips

Hot galvanised carbon steel

Furnished with hex nuts. Meet USA Fed. Spec. FF-C-450c, Type I, Class 1. This category may be available in the new MBA online store at Attachments - Wire Rope Clips - Carbon Steel.


Pins - Dowel - Stepped - Extractable - Carbon Steel - Chamfered Ends
Pins - Dowel - Stepped - Extractable - Carbon Steel - Chamfered Ends

Also see combined categories:
All Dowel Pins

Precision Extractable Dowel Pins with a Step


Related Information:


Pins - Taper - Imperial - Miniature - Carbon Steel
Pins - Taper - Imperial - Miniature - Carbon Steel

Also see combined categories:
All Imperial Taper Pins

Imperial Sizes Tapered 1:48 (1/4 in. per foot). Miniature sizes.

This category may be available in the new MBA online store at Pins - Taper - Imperial - Miniature - Carbon Steel.

Related Information:


Pins - Taper - Imperial - Standard - Carbon Steel
Pins - Taper - Imperial - Standard - Carbon Steel

Also see combined categories:
All Imperial Taper Pins

Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.

This category may be available in the new MBA online store at Pins - Taper - Imperial - Standard - Carbon Steel.

Related Information:


Screws - Shoulder - Socket Head - Carbon Steel
Screws - Shoulder - Socket Head - Carbon Steel

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Socket Head - Carbon Steel.


Sleeves - Square Hole - Plain - Carbon Steel
Sleeves - Square Hole - Plain - Carbon Steel

Also see combined categories:
All Square Hole Sleeves

Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.

This category may be available in the new MBA online store at Sleeves - Square Hole - Plain - Carbon Steel.


Sleeves - Square Hole - Threaded - Carbon Steel
Sleeves - Square Hole - Threaded - Carbon Steel

Also see combined categories:
All Square Hole Sleeves

Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through and threaded internally at one end.

This category may be available in the new MBA online store at Sleeves - Square Hole - Threaded - Carbon Steel.


Washers - Spring - Wave Type - Carbon Steel
Washers - Spring - Wave Type - Carbon Steel

Also see combined categories:
All Wave Washers

Wave Washers - also called crinkle wave. Includes 2 and 3 wave types. This category includes EPL type bearing pre-load washers.

This category may be available in the new MBA online store at Washers - Spring - Wave Type - Carbon Steel.


Feeler Gauge Stock - C1095 Carbon Steel
Feeler Gauge Stock - C1095 Carbon Steel


Used for close spacing and extremely tight tolerance situation.

Rc48-62 hardness. High carbon steel. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138704 products in 2019 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138704 products in 2019 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.