Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
Related Information:
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
Related Information:
Recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and Less than 9.
For Drylin Bearings.
Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and less than 9.
You may also be interested in
Shafting Precision Ground
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
Related Information:
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.
Related Information:
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium.
Related Information:
Includes linear shafting.
Includes shaft to h6 tolerances. Support is made from aluminium.
Related Information:
Engineering and Hobby Rod
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
Related Information:
Tube and Tubing
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
Related Information:
For general hobby applications. This tube is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.
Engineering and Hobby Rod
For general hobby applications. This rod is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.
Great little boxes ready for you to adapt to your mechanical projects.
Excellent screening properties for EMI and RFI. Ideal for projects subject to weather. Great housings for mechanical projects. Easy to machine. 380 Die Cast aluminium alloy BS1490 LM24. Close fitting flanged lids.
Thin and thick Aluminum strip and rectangular profiles
Small sizes may not be perfectly straight.
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer.
Aluminum knurled head thumb screws
Rust proof nickel plated made from finest quality zinc aluminium alloy
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft.
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
Related Information:
Tolerance of Roller Outside Diameter (D) is +/-0.075 mm
Urethane 60 Durometer ground outside diameter. Aluminium sleeve. Feed rollers do not have a rotating bore. They are designed to turn with the shaft.
Related Information:
Shaft spacers - Aluminium
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Related Information:
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Related Information:
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Related Information:
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Related Information:
Great little boxes ready for you to adapt to your mechanical or electrical projects.
Internal guide slots for mounting PCB assemblies vertically. Ideal for housing sensitive electrical, mechanical, pneumatic or hydraulic devices. Provides effective shielding of EMI and RFI. Designed to IP65 of IEC529 and NEMA 4 (dust and hoseproof). The lid incorporates a recessed neoprene gasket.
Non precision inexpensive aluminium sheet for hobby applications. Heat-treated T1100 grade.
Sheet for applications not requiring absolute precision. Thickness tolerances +/- 0.1mm. Lengths and widths will be at least that specified but may be more.
Non precision inexpensive aluminium sheet for hobby applications. Heat-treated T7075 grade.
Sheet for applications not requiring absolute precision. Thickness tolerances +/- 0.1mm. Lengths and widths will be at least that specified but may be more.
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
PCD = No. of Teeth x 0.212mm (1/120 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Metallic. Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 120 Diametrical Pitch. Approx 0.66mm between teeth. For easy ready selected sets of rack and gear please see the
HES website.
Related Information:
PCD = No. of Teeth x 0.318mm (1/80 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Metallic. Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 80 Diametrical Pitch. Approx 1mm between teeth. For easy ready selected sets of rack and gear please see the
HES website.
Related Information:
PCD = No. of Teeth x 0.265mm (1/96 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Metallic. Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 96 Diametrical Pitch. Approx 0.83mm between teeth. For easy ready selected sets of rack and gear please see the
HES website.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
PCD = No. of Teeth x 0.397mm (1/64 in.). 20o Pressure Angle. 5052 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Plastic and metallic. Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the
HES website.
Related Information:
PCD = No. of Teeth x 0.353mm (1/72 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Plastic and metallic. Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the
HES website.
Related Information:
Knurled head aluminum thumb screws with an integral washer
2024-T4 Aluminum
2024-T4 Aluminum
2024-T4 Aluminum
2024-T4 Aluminum
2024-T4 Aluminum
2024-T4 Aluminum
METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
Related Information:
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 2024 aluminium
Metallic and plastic. Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the
HES website.
Related Information:
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium
Metallic and plastic. Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the
HES website.
Related Information:
PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. 2024 aluminium.
Metallic and plastic. Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the
HES website.
Related Information:
For countersunk screws.
Aluminium solid cup washers.
Flat washers.
Related Information:
Hollow square tubing for general hobby applications.
Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 124481
products in 2754 categories including
ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.