General tool sets, screwdriver sets, tap sets, dies sets, hex key sets.
This category may be available in the new MBA online store at
Tools - Sets.
Handy sets of popular sized hex and torx wrenches.
Highest quality 8650 chrome nickel alloy heat treated and finished to resist rust. Ergo style has colour coded handles. Classic style has one piece steel grip handle. Conveniently folds up like a jack knife when not in use. This category may be available in the new MBA online store at
Tools - Sets - Foldup.
Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.
Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer. This category may be available in the new MBA online store at
Inserts - Thread Repair - Keylocking Starter Sets.
Related Information:
Partially threaded metric slotted drive set screws - grub screws
Related Information:
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
Related Information:
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
Related Information:
Cone point grub screws
Related Information:
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Standard DIN913 grub screws. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at
Socket Set Screws - Cup Point - Titanium - CP Grade 1 - DIN916.
Related Information:
Standard DIN916 grub screws with cup point. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Related Information:
Grub screws that grip rough shafts.
Related Information:
Dog point grub screws
Related Information:
Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.
Related Information:
Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.
Related Information:
Flat tip grub screws
Related Information:
Standard DIN913 grub screws with flat end. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Related Information:
Half Dog Point grub screws
Related Information:
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Related Information:
Rolling ball tip for locating into a hole
Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. This category may be available in the new MBA online store at
Socket Set Screws - Rolling Ball Tip - Carbon Steel.
Related Information:
Rolling ball tip for locating into a hole
Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. This category may be available in the new MBA online store at
Socket Set Screws - Rolling Ball Tip - Stainless Steel.
Related Information:
Solder tipped grub screws. Allow fine adjustment and spreads over the contacting surface so as not to mark or deform it.
Related Information:
Grade 8 hreat treated alloy steel. All screws are threaded to the head.
Grade 8 hreat treated alloy steel. All screws are threaded to the head.
0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000. This category may be available in the new MBA online store at
Couplings - Rigid - Set Screw.
Related Information:
Fully threaded hex head set screws (DIN933). Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Used in critical aircraft structural components. UNS R56400. Din 933. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm
2. Yield Strength 84.5kgf / mm
2. Elongation 10 Percent. This category may be available in the new MBA online store at
Screws - Hex Head - Set - Titanium Ti-Gr5 - Ti-6Al4v.
Related Information:
Spherical Seat Washers
Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3
o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at
Washers - Self Aligning - Sets - Hardened Steel.
Spherical Seat Washers
AISI 303 Stainless Steel. Max Shaft Size Shown will allow 3
o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at
Washers - Self Aligning - Sets - Stainless Steel.
From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).
Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.
Related Information:
Aluminium - Flexible.
Related Information:
Metric and Imperial High Speed Steel tap sets including taper, intermediate and bottoming tap in each set
High Speed Steel (HSS) Short Machine taps. Older stock is Triangle Brand (UK). Newer stock is Volkel Brand (German). This category may be available in the new MBA online store at
Tools - Taps - High Speed Steel - Hand - Sets.
Number punch and letter punch sets
Lengths shown are based on standard stock but may vary. This category may be available in the new MBA online store at
Tools - Punches.
Standard one piece nylon shaft collar with set screw
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at
Collars - Shaft - Standard - Nylon.
Related Information:
BSW and METRIC - Set Screws
Related Information:
Fully threaded hex head set screws (DIN933). CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Din 933. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at
Screws - Hex Head - Titanium CP Grade 1.
Related Information:
Press on knobs hold on securely without threads or set screws
Shaft diameter should be +0.000 / - 0.076 mm for best performance. Knob is held in place by a ribbed insert that squeezes onto the shaft. Eliminates machining costs. Knobs will not come off with normal use but can be removed by knocking with a hammer on the underside. This category may be available in the new MBA online store at
Knobs - Oval Tapered - Press On - Phenolic.
Related Information:
Butane Torch, Inspection Mirror, Mini Sandblaster, Nibbling Tool, Plastic Scriber, Pick Up Tool Set, Hex Driver Handle for Insert Bits
X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more. This category may be available in the new MBA online store at
Tools - General.
2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.
Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
Inch to Metric / Inch to Inch / Metric to Metric. Brass reducing bushes.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub. This category may be available in the new MBA online store at
Reducers - Bore.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138616
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.