Small Parts & Bearings - an MBA company

Sealing Plugs Stainless Sleeve With Hardened Ball Categories


Sealing Plugs


Sealing Plugs - Stainless Sleeve with Hardened Ball
Sealing Plugs - Stainless Sleeve with Hardened Ball


The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.

Sleeve: Stainless Steel DIN 1.4305, AISI 303. Ball: Bearing Steel, Heat Treated. Hardness: HB = 220.


You may also be interested in

Plungers Ball


Plungers - Ball - Push Fit - 303 Stainless Steel
Plungers - Ball - Push Fit - 303 Stainless Steel

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded

Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.


Sealing Plugs


Sealing Plugs - Stainless Sleeve and Ball
Sealing Plugs - Stainless Sleeve and Ball


The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.

Sleeve: Stainless Steel DIN 1.4305, AISI 303 Clear passivated to MIL S 5002 Aerospace Quality. Ball: Stainless Steel DIN 1.4301, AISI 304 Clear passivated to MIL S 5002 Aerospace Quality. Hardness: HB = 220.


Plungers Ball


Plungers - Ball - Push Fit - Plastic Body - Plastic Ball
Plungers - Ball - Push Fit - Plastic Body - Plastic Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded. Plastic body and ball.

Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.


Shafting - Ground - Precision - Stainless 416 Grade Hardened
Shafting - Ground - Precision - Stainless 416 Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.


Related Information:


Shafting - Ground - Precision - Stainless 420 Grade Hardened
Shafting - Ground - Precision - Stainless 420 Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.


Related Information:


Shafting - Ground - Precision - Stainless 440C Grade Hardened
Shafting - Ground - Precision - Stainless 440C Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.


Related Information:


Balls - Checking - Stainless Steel
Balls - Checking - Stainless Steel

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Fixture - Stainless Steel
Balls - Fixture - Stainless Steel

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Checking - Stainless Steel - With Tapped Shank
Balls - Checking - Stainless Steel - With Tapped Shank

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Bearings - Thrust - Ball - Washers Only - Stainless Steel
Bearings - Thrust - Ball - Washers Only - Stainless Steel

Also see combined categories:
All Ball Thrust Bearing Components

Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.

Stainless Steel Washers are hardened to HRC38.42.

Related Information:


Collars - Shaft - Hinged - Stainless Steel
Collars - Shaft - Hinged - Stainless Steel

Also see combined categories:
All Round Bore Shaft Collars
All Hinged Shaft Collars

Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel

Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.

Related Information:


Sleeves - Hex Hole - Hardened
Sleeves - Hex Hole - Hardened

Also see combined categories:
All Hex Hole Sleeves

Pre hardened to Rockwell 23-30C. Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.



Sleeves - Square Hole - Plain - Hardened
Sleeves - Square Hole - Plain - Hardened

Also see combined categories:
All Square Hole Sleeves

Pre hardened to Rockwell 23-30C. Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.



Bearings - Linear - Ball - Stainless Steel - Closed
Bearings - Linear - Ball - Stainless Steel - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Related Information:


Bearings - Needle Roller - Inner Rings
Bearings - Needle Roller - Inner Rings


Hardened sleeves for needle roller bearings.


Related Information:


Couplings - Rigid - 1 Piece Clamp - Stainless Steel
Couplings - Rigid - 1 Piece Clamp - Stainless Steel

Also see combined categories:
All Rigid Couplings

303 Grade Stainless

Precision Machined. High torsional load. Non marring, easy to install and adjust. Use on hardened shafts, rigid clamp type design, easily machinable. Available with stepped bores and keyways on 5 week delivery.


Plungers - Ball - Threaded - With Limit Switch
Plungers - Ball - Threaded - With Limit Switch

Also see combined categories:
All Threaded Ball Plungers

Suitable for locking and releasing a device by using a built-in electrical switch. Stainless steel spring, nickel plated body, hardened steel ball.

Supply Cable : Grey for normally open contacts, black for normally closed. Oil resistant. Max tensile load 20N. Working Temperature: -10 deg C to 80 deg C. Electrical Supply : 20 mA DC Max. Switching load recommended 5-10 mA. Voltage : 12-24V Supply Cable 3mm - 2 Phase, 2 metres long. Safety Standard : IP40 Average Switch Life Span : 3 milliion switchings.


Bearings - Hydrodynamic Pressure
Bearings - Hydrodynamic Pressure


Alternative to ball bearings - quiet operation - patented design.

Applications include compact fan motors, copy machines, printers, laptop computers, cameras and toys. Stainless Steel casing and shield - Long Life. Use with Case Hardened shafting 2um surface finish -0.007/-0.012 for normal use. Use with Case Hardened shafting 1um surface finish -0.005/-0.007 for high accuracy use. 30% weight savings over ball bearings.

Related Information:


Screws - Captive - Retractable - Steel
Screws - Captive - Retractable - Steel

Also see combined categories:
All Captive Screws

Compliance with UL 1950 and EN 60950 codes for access areas. Ratchet mechanism allows screw to be tightened down by hand, but a tool is needed to loosen.Fully retractable captive to the panel and spring ejected.

Press in style. Bright chromate zinc plated, case hardened steel with aluminium knob and stainless steel spring. Knobs available either slotted or no.2 phillips.


Washers - Flat - Hardened Steel
Washers - Flat - Hardened Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.


Related Information:


Rollers - Steel
Rollers - Steel

Also see combined categories:
All Rollers

Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings

Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.

Related Information:


Washers - Self Aligning - Components - Hardened Steel
Washers - Self Aligning - Components - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.

Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.


Washers - Self Aligning - Sets - Hardened Steel
Washers - Self Aligning - Sets - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.


Linear Slides - MiniVee - Track - Hardened Steel
Linear Slides - MiniVee - Track - Hardened Steel


Use with MiniVee carriages and support washers

Low profile miniature linear slide system ideal for semi-conductor, laboratory, medical and packaging applications. Non actuated MiniVee linear slide consists of one or more 6061-T6 anodised aluminium wheel carriages with Dual Vee integrated wheels. Double edged track from 165 to 927mm. Carriages and track sold separately.

Related Information:


Pins - Dowel - Extractable
Pins - Dowel - Extractable

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6. Din 7979.

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.

Related Information:




Pins - Dowel - Extractable - With Vent
Pins - Dowel - Extractable - With Vent

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6 with a ground flat along one edge

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650. Also known as parallel pins.

Related Information:


Washers - Serrated - Safety
Washers - Serrated - Safety

Also see combined categories:
All Serrated Locking Washers

Spring Steel Hardened Black.



Strip - Spring Steel
Strip - Spring Steel

Also see combined categories:
All Metal Strip

Hundreds of uses.

Hardened and tempered spring steel strip. Note that the width of this strip may vary up to a few mm as it is guillotine cut from strip. If you require a closer tolerance on the strip width please contact us prior to ordering.


Rod - Drill Blanks
Rod - Drill Blanks

Also see combined categories:
All Silver Steel Drill Blanks
All Drill Rod

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.


Bearings - Thrust - Ball - Washers Only - Chrome Steel
Bearings - Thrust - Ball - Washers Only - Chrome Steel

Also see combined categories:
All Ball Thrust Bearing Components

Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.

Carbon Steel Washers are hardened to RC59.61.

Related Information:


Washers - C - Swing
Washers - C - Swing


Cold finished steel, hardened and ground. Black oxide finish.



Washers - Heavy Duty - Machined - Steel
Washers - Heavy Duty - Machined - Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

Case hardened cold finished steel with black oxide finish.


Related Information:


Shaftloc-tm Sleeves - Single Ended
Shaftloc-tm Sleeves - Single Ended

Also see combined categories:
All Shaftloc

Simple effective way to lock components onto shafts.

416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened.

Related Information:


Washers - C - Steel
Washers - C - Steel

Also see combined categories:
All C Washers

Cold finished steel, case hardened with a black oxide finish.



Studs - Ball - Threaded
Studs - Ball - Threaded


Zinc Plated Steel DIN 71803 Form C. Surface Hardened to 55 HRC (Ball (D1) Only - Thread is Not Hardened).


Shafting - Ground - Precision - High Carbon Steel
Shafting - Ground - Precision - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.


Related Information:


Mounts - Leveling - Stud Type - Gold Chromate - Imperial
Mounts - Leveling - Stud Type - Gold Chromate - Imperial

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Good quality with value pricing. Hardened ball for high load ratings and excellent wear characteristics. Adjusters.

Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces.

Related Information:


Mounts - Leveling - Stud Type - Gold Chromate - Metric
Mounts - Leveling - Stud Type - Gold Chromate - Metric

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Good quality with value pricing. Hardened ball for high load ratings and excellent wear characteristics. Adjusters.

Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces.

Related Information:


Mounts - Leveling - Stud Type - Nickel Plated - Imperial
Mounts - Leveling - Stud Type - Nickel Plated - Imperial

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Good quality with value pricing. Hardened ball for high load ratings and excellent wear characteristics. Adjusters.

Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces.

Related Information:


Mounts - Leveling - Stud Type - Nickel Plated - Metric
Mounts - Leveling - Stud Type - Nickel Plated - Metric

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Good quality with value pricing. Hardened ball for high load ratings and excellent wear characteristics. Adjusters.

Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces.

Related Information:


Rod Ends - Steel - Studded - Quick Disconnect - Female
Rod Ends - Steel - Studded - Quick Disconnect - Female

Also see combined categories:
All Female Rod Ends with Stud

Joints are strength, quick disconnect assemblies with good wear characteristics. Retaining sleeve insures the assembly can only be put together with the sleeve positively aligned with the ball cavity. When spring is released, alignment is automatic thereby eliminating any possiblity of partial closure. Ball stud and Body are made of low carbon steel. Studs are surface hardened. All Parts are plated and dichromate treated.


Rod - Drill - W-1 Water Hardening
Rod - Drill - W-1 Water Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.


Bushings - Drill - Liner Type - Headless
Bushings - Drill - Liner Type - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Bushings - Drill - Press-fit - Headless
Bushings - Drill - Press-fit - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.



Bushings - Drill - Slip - With Head
Bushings - Drill - Slip - With Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Rod Ends - Steel - Studded - Nylon Seat - Female
Rod Ends - Steel - Studded - Nylon Seat - Female

Also see combined categories:
All Female Rod Ends with Stud

Housing is plated and dichromate treated steel. Ball is case hardened and plated. Stud is permanently affixed and made from heat treated alloy steel, zinc plated.


Rod Ends - Steel - Studded - Nylon Seat - Male
Rod Ends - Steel - Studded - Nylon Seat - Male

Also see combined categories:
All Male Rod Ends with Stud

Housing is plated and dichromate treated steel. Ball is case hardened and plated. Stud is permanently affixed and made from heat treated alloy steel, zinc plated.


Rod Ends - Steel - Studded - PTFE Seat - Female
Rod Ends - Steel - Studded - PTFE Seat - Female

Also see combined categories:
All Female Rod Ends with Stud

Housing is plated and dichromate treated steel. Ball is case hardened and plated. Stud is permanently affixed and made from heat treated alloy steel, zinc plated.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 127032 products in 2380 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 127032 products in 2380 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.