Small Parts & Bearings - an MBA company

Screws Wood Brass Categories


Screws Wood


Screws - Wood - Brass
Screws - Wood - Brass


Brass wood screws for models



You may also be interested in

Thread Inserts


Inserts - Self Tapping - For Wood - Slotted Drive - Short
Inserts - Self Tapping - For Wood - Slotted Drive - Short

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Brass. Install with a screwdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into a drilled hole.


Inserts - Self Tapping - For Plastics - Stainless 303
Inserts - Self Tapping - For Plastics - Stainless 303

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.

Related Information:


Screws Countersunk


Screws - Countersunk - Brass - Slotted
Screws - Countersunk - Brass - Slotted

Also see combined categories:
All Countersunk Screws

Flat Head Countersunk METRIC and BSW

Nuts sold seperately - See Nuts.

Related Information:


Screws Thumb


Screws - Thumb - Knurled - Brass
Screws - Thumb - Knurled  - Brass

Also see combined categories:
All Thumb Screws

Brass knurled head thumb screws with zinc or black oxide protective coating.



Screws Cheese Head


Screws - Fillister Head - Brass - Philips
Screws - Fillister Head - Brass - Philips

Also see combined categories:
All Machine Screws
All Brass Machine Screws

Brass metal thread machine screws BA and METRIC

Nuts sold seperately - See Nuts.

Related Information:


Screws - Fillister Head - Brass - Slotted
Screws - Fillister Head - Brass - Slotted

Also see combined categories:
All Machine Screws
All Brass Machine Screws

Brass metal thread machine screws BA and METRIC

Nuts sold seperately - See Nuts.

Related Information:


Screws Hex Head


Screws - Hex Head - Brass
Screws - Hex Head - Brass

Also see combined categories:
All Machine Screws
All Brass Machine Screws

Brass metal thread machine screws UNC and UNF

Nuts sold seperately - See Nuts.

Related Information:


Screws Pan Head


Screws - Pan Head - Brass - Slotted
Screws - Pan Head - Brass - Slotted

Also see combined categories:
All Machine Screws
All Brass Machine Screws

Brass metal thread machine screws METRIC

Nuts sold seperately - See Nuts.

Related Information:


Screws Round Head


Screws - Round Head - Brass - Slotted
Screws - Round Head - Brass - Slotted

Also see combined categories:
All Machine Screws
All Brass Machine Screws

Brass metal thread machine screws BSW - UNF - UNC

Nuts sold seperately - See Nuts.

Related Information:


Screws Thumb


Screws - Thumb - Knurled - Washer Face - Brass
Screws - Thumb - Knurled - Washer Face - Brass

Also see combined categories:
All Thumb Screws

Knurled head brass thumb screws with an integral washer



Screws Cap Head


Screws - Cap - Socket - Alloy Steel - Brass Tipped
Screws - Cap - Socket - Alloy Steel - Brass Tipped

Also see combined categories:
All Socket Cap Screws
All Soft Tipped Grub Screws

Brass tipped socket cap screws in alloy steel



Screws Grub


Socket Set Screws - Brass Tipped - Alloy Steel
Socket Set Screws - Brass Tipped - Alloy Steel

Also see combined categories:
All Soft Tipped Grub Screws
All Grub Screws

Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.


Related Information:


Socket Set Screws - Brass Tipped - Stainless Steel
Socket Set Screws - Brass Tipped - Stainless Steel

Also see combined categories:
All Soft Tipped Grub Screws
All Grub Screws

Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.


Related Information:


Ball Transfers


Ball Transfer Units - Screw Stem - Brass and Aluminium
Ball Transfer Units - Screw Stem - Brass and Aluminium

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


Washers Finishing


Washers - Cup - Brass - Nickel Plated
Washers - Cup - Brass - Nickel Plated

Also see combined categories:
All Cup Washers

For countersunk screws.



Couplings Rigid


Couplings - Rigid - Set Screw
Couplings - Rigid - Set Screw

Also see combined categories:
All Rigid Couplings

0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.

Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000.

Related Information:


Screws Self Tapping


Screws - Self Drilling - Pan Head
Screws - Self Drilling - Pan Head

Also see combined categories:
All Self Drilling Screws

Zinc chromate fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.



Screws - Self Drilling - Hex Washer Head
Screws - Self Drilling - Hex Washer Head

Also see combined categories:
All Self Drilling Screws

Zinc chromate. Fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.



Thread Inserts


Inserts - Self Tapping - For Wood - Hex Drive
Inserts - Self Tapping - For Wood - Hex Drive

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.


Inserts - Self Tapping - For Wood - Slotted Drive
Inserts - Self Tapping - For Wood - Slotted Drive

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.

Related Information:


Inserts - Self Tapping - For Wood - Hex Drive - Flanged
Inserts - Self Tapping - For Wood - Hex Drive - Flanged

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.


Knobs Pointer


Knobs - Pointer - Skirted
Knobs - Pointer - Skirted

Also see combined categories:
All Pointer Knobs

Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass insert.



Knobs - Pointer - Aluminium and Plastic
Knobs - Pointer - Aluminium and Plastic

Also see combined categories:
All Pointer Knobs

Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer.



Universal Joints Single


Universal Joints - Single Joint - Plastic - Brass Spider
Universal Joints - Single Joint - Plastic - Brass Spider

Also see combined categories:
All Universal Joints
All Single Joint Universals

Plain acetal with brass centre, no bore inserts or grub screw holes



Universal Joints Double


Universal Joints - Double Joint - Plastic - Brass Bore Inserts
Universal Joints - Double Joint - Plastic - Brass Bore Inserts

Also see combined categories:
All Universal Joints
All Double Joint Universals

Plain acetal with brass centre, brass bore inserts and grub screw holes



Universal Joints Single


Universal Joints - Single Joint - Plastic - Brass Bore Inserts
Universal Joints - Single Joint - Plastic - Brass Bore Inserts

Also see combined categories:
All Universal Joints
All Single Joint Universals

Plain acetal with brass centre, brass bore inserts and grub screw holes



Shaft Extenders and Reducers


Reducers - Bore
Reducers - Bore


Inch to Metric / Inch to Inch / Metric to Metric. Brass reducing bushes.

S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.

Related Information:


Thread Inserts


Inserts - Self Tapping - For Plastics - Steel
Inserts - Self Tapping - For Plastics - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.

Related Information:


Gears Inch Spur


Gears - Spur - 24DP - 20 Degree - Brass
Gears - Spur -  24DP - 20 Degree - Brass

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 24DP - 20 Degree - Plastic with No Hub
Gears - Spur -  24DP - 20 Degree - Plastic with No Hub

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Nuts Hex


Nuts - Hexagonal - Brass
Nuts - Hexagonal - Brass

Also see combined categories:
All Nuts

UNC - UNF - BA - METRIC.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.


Pins Dowel


Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:


Gears Inch Spur


Gears - Spur - 24DP - 20 Degree - Plastic - Plain
Gears - Spur -  24DP - 20 Degree - Plastic - Plain

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 24DP - 20 Degree - Plastic with Insert
Gears - Spur -  24DP - 20 Degree - Plastic with Insert

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Inserts - Expansion - Press In - Brass
Inserts - Expansion - Press In - Brass

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.


Inserts - Expansion - Press In - Brass - Flanged
Inserts - Expansion - Press In - Brass - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.


Assortment Kits - Various
Assortment Kits - Various


Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Shim - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins



Bumpers - Cylindrical - Rubber
Bumpers - Cylindrical - Rubber

Also see combined categories:
All Cylindrical Bumpers

Built in steel screw for easy instrallation. Made with abrasion resistant SBR rubber. Resistant to abrasion and oxidation. Excellent cushioning and vibration control.

Non staining, non marring polyurethane. Sold by the pad - number of bumpers per pad shown in the listings. Peel off and apply. Clear. 60-70 Shore A hardness.


Bumpers - Domed - Rubber
Bumpers - Domed - Rubber


Built in steel screw for easy instrallation. Made with abrasion resistant SBR rubber. Resistant to abrasion and oxidation. Excellent cushioning and vibration control.

Non staining, non marring polyurethane. Sold by the pad - number of bumpers per pad shown in the listings. Peel off and apply. Clear. 60-70 Shore A hardness.


Cross Blocks - Heavy Duty - Two Knobs
Cross Blocks - Heavy Duty - Two Knobs

Also see combined categories:
All Cross Blocks
All Swivel Joints and Cross Blocks

Used for connecting two round rods at 90o.

Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.


Screws - Roof Bolt - Steel
Screws - Roof Bolt - Steel

Also see combined categories:
All Machine Screws

Metal Thread Screws. Metric and BSW only. Supplied with nut.

Nuts sold seperately - See Nuts.

Related Information:


Screws - Hex Head - Steel - Zinc Plated
Screws - Hex Head - Steel - Zinc Plated

Also see combined categories:
All Hex Head Screws

BSW and METRIC - Bolts


Related Information:


Screws - Shoulder - Slotted Shallow Head - Carbon Steel
Screws - Shoulder - Slotted Shallow Head - Carbon Steel

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts.


Screws - Shoulder - Socket Head - 303 Stainless
Screws - Shoulder - Socket Head - 303 Stainless

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts.


Screws - Shoulder - Socket Head - 416 Stainless
Screws - Shoulder - Socket Head - 416 Stainless

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts.


Screws - Shoulder - Socket Head - Carbon Steel
Screws - Shoulder - Socket Head - Carbon Steel

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts.


Screws - Shoulder - Slotted Head - Stainless
Screws - Shoulder - Slotted Head - Stainless

Also see combined categories:
All Shoulder Screws

303 Stainless Steel

Also known as stripper bolts.


Screws - Shoulder - Jig and Fixture - Steel
Screws - Shoulder - Jig and Fixture - Steel

Also see combined categories:
All Shoulder Screws

Used in construction of tool, jig and fixture work. 4140L heat treated steel with black oxide finish.

Also known as stripper bolts.


Tools - Screw Extractors
Tools - Screw Extractors

Also see combined categories:
All Tools

The quick and easy way to remove broken screws, bolts, pipes and studs.

Note! You will also need a drill bit of the correct size for each extractor.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124370 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124370 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.