Screws Self Tapping
Tri-Lobe Course Thread Plastic Threading Screws
Tri-Lobe Course Thread Plastic Threading Screws
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
Threaded inserts are screwed into pre-formed or pre-drilled holes and cut their own threads. Perfect for permanent installations.
Made from brass. Install with a screwdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into a drilled hole. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Slotted Drive - Short.
Zinc chromate fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.
Type AB Steel Self Tapping Screws.
Type AB Steel Self Tapping Screws.
Type AB Steel Self Tapping Screws.
Type AB Steel Self Tapping Screws.
Zinc chromate. Fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Hex Drive.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Hex Drive - Flanged.
Machine screws. PEEK is a super-engineering thermoplastic with special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of VitreTM.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180o Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
Related Information:
PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at
Gears - Spur - 24DP - 20 Degree - Plastic - Plain.
Self lubricated, high mechanical strength, stiffness and hardness.
Related Information:
PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
Installation tools for self tapping thread inserts - see the linked inserts categories
Related Information:
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at
Nuts - Hexagonal - Nylon - Self Tapping.
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs. This category may be available in the new MBA online store at
Collars - Shaft - Gripfast - ABS Plastic.
Related Information:
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Spacers for printed circuit boards
These spacers have a hex in the centre to allow for holding with a spanner whilst tightening. Fix using a 6 or 8 gauge self tapping screw. This category may be available in the new MBA online store at
Spacers - PCB.
Polyvinyl chloride. PVC is a chemically stable material, which shows little change in molecular structure, and also exhibits little change in its mechanical strength.
Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. It is easily worked or machined and has good chemical and biological resistance. It is relatively hard and can be polished to a shine. Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. Heat Deflection Temperature 176 F / 80 C. Rockwell Hardness 115. Zero water absorption in 24 hours.
Related Information:
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight. This category may be available in the new MBA online store at
Balls - Plastic - Bored.
Related Information:
Plastic spherical plain bearings. Also known as ball bushings.
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Butane Torch, Inspection Mirror, Mini Sandblaster, Nibbling Tool, Plastic Scriber, Pick Up Tool Set, Hex Driver Handle for Insert Bits
X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more. This category may be available in the new MBA online store at
Tools - General.
Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.
Case Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-G washers are used for clamping mechanical parts with non-parallel surfaces. Designed for screw solidity in compliance with 8.8. Limited for use on flat closed ring areas - not for elongated holes.
Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)
Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288
oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon
(R) product range. This category may be available in the new MBA online store at
Bushes - Plastic - Rulon J - Flanged.
Related Information:
Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)
Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288
oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon
(R) product range. This category may be available in the new MBA online store at
Bushes - Plastic - Rulon J - Unflanged.
Related Information:
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Housing : Plastic / Shaft : Steel. This category may be available in the new MBA online store at
Gearmotors - DC - Low Voltage.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.