Washers Finishing
For countersunk screws.
Screws Countersunk
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. Rc38-42. ASTM F835 - alloy steel. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks.
Related Information:
Flat Head Countersunk. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Metric Sizes to DIN7991. Used in critical aircraft structural components. UNS R56400. ISO 10642. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. Rc38-42. ASTM F835 - alloy steel. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC - Stainless Steel
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks. This category may be available in the new MBA online store at
Screws - Countersunk - Socket - 304 Stainless.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC - Stainless Steel
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks. This category may be available in the new MBA online store at
Screws - Countersunk - Socket - 316 Stainless.
Related Information:
Screws Security
Metric only.
Related Information:
Metric only.
Related Information:
You may also be interested in
Screws Cap Head
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN912. This category may be available in the new MBA online store at
Screws - Cap - Socket - Aluminium.
Related Information:
Housings for Ball Bearings
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
Screws Countersunk
Flat Head Countersunk. Metric only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at
Screws - Countersunk - Titanium CP Grade 1 - Philips Drive.
Related Information:
Flat Head Countersunk. Metric only. CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. This category may be available in the new MBA online store at
Screws - Countersunk - Titanium CP Grade 2 - Philips Drive.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC.
Related Information:
Flat Head Countersunk METRIC and BSW
Related Information:
Flat Head Countersunk UNC and UNF.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
Related Information:
Flat Head Countersunk. Metric only.
Related Information:
Flat Head Countersunk. Metric only.
Related Information:
Flat Head Countersunk. Metric small selection only.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC
Related Information:
Flat Head Countersunk UNC - UNF - METRIC
Related Information:
Flat Head Countersunk UNC - UNF - BA - METRIC
Related Information:
Screws Self Tapping
Washers Finishing
Countersunk washers for use with screws for decorative finishing
For countersunk screws.
For countersunk screws.
Screws Thumb
Knurled head aluminum thumb screws with an integral washer
Related Information:
Screws Pan Head
UNC metal thread machine screws
Related Information:
Thread Inserts
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
Ball Transfers
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at
Ball Transfer Units - Screw Stem - Brass and Aluminium.
Couplings Helical and Slit
Related Information:
Clamps
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Couplings Helical and Slit
Aluminium - Flexible.
Couplings Rigid
0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000. This category may be available in the new MBA online store at
Couplings - Rigid - Set Screw.
Related Information:
Pins Pull
Spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations.
Two part assembly includes a barrel and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. 3/8-16 Threaded end so you can add your own handle or knob. Aluminium housing 6061-T6, Steel pin 12L15. Pull up force approx 2.2kg.
Related Information:
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations.
Two part assembly includes a barrel and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. Handles are black plastic. Aluminium housing 6061-T6, Steel pin 12L15. Pull up force approx 2.2kg. Lockout style (indicated in tables) allows you to pull and rotate handle 1/4 turn to lock plunger in retracted position.
Related Information:
Spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations.
Two part assembly includes a barrel and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. Handles are black plastic. Aluminium housing 6061-T6, Steel pin 12L15. Pull up force approx 2.2kg. Lockout style (indicated in tables) allows you to pull and rotate handle 1/4 turn to lock plunger in retracted position.
Related Information:
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.