Screws Button Head
UNC - UNF - METRIC.
Related Information:
You may also be interested in
Screws Cap Head
UNC - UNF - METRIC - Alloy Steel.
Related Information:
Brass tipped socket cap screws in alloy steel
Alloy steel socket cap screws with nylon locking pellet
Nylon tipped socket cap screws in alloy steel
Screws Grub
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
Related Information:
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Related Information:
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Screws Countersunk
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. Rc38-42. ASTM F835 - alloy steel. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks.
Related Information:
Screws Cap Head
UNC - UNF - METRIC - Alloy Steel.
Note. Hex key size may. The size listed is the usual and minimum size. This category may be available in the new MBA online store at
Screws - Low Head - Socket.
Related Information:
UNC - UNF - METRIC - Alloy Steel.
Related Information:
Screws Countersunk
Flat Head Countersunk UNC - UNF - METRIC
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. Rc38-42. ASTM F835 - alloy steel. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks.
Related Information:
Screws Button Head
Sheet metal screws
Related Information:
UNC - UNF - METRIC.
Related Information:
UNC - UNF - METRIC.
Related Information:
UNC - UNF - METRIC.
Related Information:
Screws Security
Metric only.
Related Information:
Screws Shoulder
Screws Grub
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
Related Information:
Dog point grub screws
Related Information:
Solder tipped grub screws. Allow fine adjustment and spreads over the contacting surface so as not to mark or deform it.
Related Information:
Screws Cap Head
Nylon tipped socket cap screws in 18-8 Stainless Steel - similar to 316 stainless
Screws Grub
Grub screws that grip rough shafts.
Related Information:
Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.
Related Information:
Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.
Related Information:
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Rolling ball tip for locating into a hole
Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. This category may be available in the new MBA online store at
Socket Set Screws - Rolling Ball Tip - Carbon Steel.
Related Information:
Rolling ball tip for locating into a hole
Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. This category may be available in the new MBA online store at
Socket Set Screws - Rolling Ball Tip - Stainless Steel.
Related Information:
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Screws Cap Head
UNC - UNF - METRIC - Stainless Steel.
Related Information:
316L Stainless Steel. Other sizes available on request.
Hexagon socket cap head with low head. Safety improvements and compact size for equipment and devices. May be used in vacuum chamber applications in clean rooms, Flat Panel Displays, Semiconductor production equipment and devices. All clean washed, preventing the inclusion of oil and foreign particles. This category may be available in the new MBA online store at
Screws - Low Head - Socket - 316L Stainless.
UNC - UNF - METRIC - Stainless Steel.
Related Information:
Screws Countersunk
Flat Head Countersunk UNC - UNF - METRIC - Stainless Steel
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks. This category may be available in the new MBA online store at
Screws - Countersunk - Socket - 304 Stainless.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC - Stainless Steel
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks. This category may be available in the new MBA online store at
Screws - Countersunk - Socket - 316 Stainless.
Related Information:
Tools Threading
Tungsten Chrome Alloy - Carbon Steel Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
Screws Countersunk
Flat Head Countersunk. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Metric Sizes to DIN7991. Used in critical aircraft structural components. UNS R56400. ISO 10642. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks.
Related Information:
Screws Cap Head
Metric Sizes to DIN912. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm
2. Yield Strength 84.5kgf / mm
2. Elongation 10 Percent. This category may be available in the new MBA online store at
Screws - Cap - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN912.
Related Information:
Screws Grub
Standard DIN916 grub screws with cup point. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Related Information:
Standard DIN913 grub screws with flat end. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Related Information:
Grade 8 hreat treated alloy steel. All screws are threaded to the head.
Grade 8 hreat treated alloy steel. All screws are threaded to the head.
12L14 Steel
Precision Machined. High torsional load. Non marring, easy to install and adjust. Assemble without moving shafts. Use on hardened shafts, rigid clamp type design, easily machinable. Black finish with alloy steel cap screws. Available with stepped bores and keyways on 5 week delivery.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.