Rod Ends Studded Categories
Rod Ends - Steel - Studded - Nylon Seat - Female
Housing is plated and dichromate treated steel. Ball is case hardened and plated. Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
Rod Ends - Steel - Studded - Nylon Seat - Male
Housing is plated and dichromate treated steel. Ball is case hardened and plated. Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
Rod Ends - Steel - Studded - PTFE Seat - Female
Housing is plated and dichromate treated steel. Ball is case hardened and plated. Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
Rod Ends - Steel - Studded - PTFE Seat - Male
Housing is plated and dichromate treated steel. Ball is case hardened and plated. Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
Rod Ends - Steel - Studded - Quick Disconnect - Female
Joints are strength, quick disconnect assemblies with good wear characteristics. Retaining sleeve insures the assembly can only be put together with the sleeve positively aligned with the ball cavity. When spring is released, alignment is automatic thereby eliminating any possiblity of partial closure. Ball stud and Body are made of low carbon steel. Studs are surface hardened. All Parts are plated and dichromate treated.
Rod Ends - Steel - Studded - Swaged Construction - Female
Designed for heavy duty service, they come with dirt shield to provide protection against contaminants.
Unique assembly swages metal to retain the ball in cavity resulting in increased pull out and wear resistance. Ball studs are surface hardened. Made of low carbon steel, plated and dichromate treated.
You may also be interested in
Rod Ends Plastic
Rod Ends - Plastic - Female
Thermoplastic Body / L280(R) Polymer Ball. Also known as Heim Joints
Dimensions not shown are available on request.
Rod Ends - Plastic - Male
Thermoplastic Body / L280(R) Polymer Ball. Also known as Heim Joints
Dimensions not shown are available on request.
Rod Ends PTFE Lined
Rod Ends - Steel - PTFE Lined - Tight Fit - Female
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon Steel. Also known as Heim Joints
Dimensions not shown are available on request.
Rod Ends - Steel - PTFE Lined - Tight Fit - Male
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon Steel. Also known as Heim Joints
Dimensions not shown are available on request.
Rod Ends Stainless Steel
Rod Ends - Stainless Steel 303 with 420 Ball - PTFE Lined - Male
Tight fit (Minimal ball clearance). Also known as Heim Joints
Dimensions not shown are available on request.
Rod Ends - Stainless Steel 304 with 420 Ball - Bronze Lined - Female
Also known as Heim Joints
Dimensions not shown are available on request.
Rod Ends - Stainless Steel - Bronze Lined - Male
Also known as Heim Joints
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
Rod Ends Stamped
Rod Ends - Steel - Stamped - Female
Economy stamped style combines high strength with low cost. Also known as Heim Joints
Made from low carbon steel and plated for corrosion resistance. Ball is case hardened.
Rod Ends Standard
Rod Ends - Steel - Bronze Lined - Female
Imperial and Metric / Carbon Steel. Also known as Heim Joints
Dimensions not shown are available on request.
Rod Ends - Steel - Bronze Lined - Male
Imperial and Metric / Carbon Steel. Also known as Heim Joints
Dimensions not shown are available on request.
Bar and Rod
Hexagonal Bar - Brass
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small A/F sizes may not be perfectly straight.
Square Bar - Brass
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.
Hexagonal Bar - 303 Stainless
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
Threaded Rod
Threaded Rod - Unthreaded Centre - Steel
UNC Small range only. Threaded each end 38.1mm (1.5 inches) and unthreaded in the centre.
Related Information:
Kites
Caps - End - Kite
End caps with string holes and grooves for kite rods.
Joiners and connectors suitable for rod and tubing as well as for kites.
Bar and Rod
Clevis Joints
Joints - Clevis - Plastic
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
Bar and Rod
Hexagonal Bar - Titanium Ti-Gr2 - Drawn
Cold rolled and hot drawn hex bar to ASTM B348
Saw Cut Ends.
Balls Metallic
Balls - Steel - Bored
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
Related Information:
Balls Plastic
Balls - Plastic - Bored
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
Related Information:
Bungs
Bungs and Caps - Reversible - Round
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges.
Related Information:
Bolts - Eye - Bent Rod - Steel
Not recommended for lifting.
Carbon steel zinc plated. Complete with nut. Rolled threads.
Rod - Drill Blanks
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.
Rod - Drill - A-2 Air Hardening
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for A-2 hardening requirements.
Rod - Drill - O-1 Oil Hardening
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for O-1 hardening requirements.
Rod - Drill - S-7 Air Hardening
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for S-7 hardening requirements.
Rod - Drill - Silversteel - W-1 Water Hardening
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for W-1 hardening requirements.
Shafts - Flexible - Coupling Ends - Open - Mild Steel
Flexible shafting with coupling ends ready to attach to a fixed shaft.
1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.
Related Information:
Rod - Round - Soft Metal Packs
For general hobby applications. This rod is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths for general hobby applications. Not recommended for heavy duty applications. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
Shaftloc-tm Sleeves - Single Ended
Simple effective way to lock components onto shafts.
416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened.
Related Information:
Rectangular Bar - Aluminium
Thin and thick Aluminum strip and rectangular profiles
Small sizes may not be perfectly straight.
Square Bar - Urethane
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Length +/- 2 percent.
Rod - Round - Aluminium
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
Related Information:
Rod - Round - Brass
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
Related Information:
Rod - Round - Stainless Steel
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
Related Information:
Snap Buttons - Double End
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
Tool Steel - 496 Oil Hardening - Flat Stock
General purpose tool steel with good wear resistance, durability and machinability
Dimensionally stable chromium, tungsten and vanadium electric furnace toolsteel can be used for intricate work. Low 787 to 815 oC (1450-1500 F) hardening range makes it easy to harden. Fully spheroidised and annealed for uniform carbide size and easy machining. Each piece is individually wrapped and clearly marked with size, analysis and correct hardness and tempering information. Edge squareness 0.003 mm per mm. Finish is 0.0008mm (0.000032 inch).
Rod - Round - Acetal
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127031 products in 2352 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
