Rod Ends Stainless Steel
Also known as Heim Joints
Also known as Heim Joints
Housing is plated and dichromate treated steel. Ball is case hardened and plated. Stud is permanently affixed and made from heat treated alloy steel, zinc plated. This category may be available in the new MBA online store at
Rod Ends - Steel - Studded - Nylon Seat - Female.
Also known as Heim Joints
Dimensions not shown are available on request.
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100
oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at
Bearings - Linear - Ball - Stainless Steel - Closed.
Related Information:
One end threaded so you can attach your own handle or knob. 303 Stainless Steel.
Related Information:
Spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations.
Two part assembly includes a barrel and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. 3/8-16 Threaded end so you can add your own handle or knob. 303 stainless steel plunger assembly and housing. Pull up force approx 2.2kg.
Related Information:
303 stainless steel (European grade 1.4305)
Related Information:
With Long-Lok thread locking compound to prevent loosening
Unthreaded
Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Full stainless steel bearing units are the best solution for hostile chemical washdown applications. All metal bearing insert components are a combination of 302, 304 and 440 stainless steel. Seals are silicone rubber. Grease is H-1 food grade.
Operating temperature minus 20 oC to +120 deg C. Solid 304 stainless housings have a machined base and extremely smooth surface finish, essential for demanding washdown installations. These housings do not experience flaking, cracking or discolouration and are virtually unaffected by scrapes. Bearings are removable. Food grade.
Levelling adjusters. These industrial glides are an excellent and inexpensive solution for light duty applications such as office furniture, shelving, point of sale displays, cabinetry and small machinery.
303 Stainless Steel. Nylon pad for glide applications.
Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.
Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food grade.
Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.
Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food Grade.
Use with NEMA Size 17 Motors.
Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).
Related Information:
Spyraflo electroless nickel plated aluminium housing with stainless steel coated self aligning acetal bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Electroless nickel plated aluminium housing. Corrosion Resistant. Light weight.
Related Information:
Also known as Heim Joints
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
Related Information:
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at
Bearings - Thrust - Ball - Grooved - Stainless Steel.
Related Information:
Spyraflo aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings. Double shielded bearings to minimise contamination. This category may be available in the new MBA online store at
Housings - Bearing - Pillow Block - Miniature.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30
oC to 100
oC Continuous. This category may be available in the new MBA online store at
Bearings - Acetal - Double Row - with 316 Stainless Steel Balls.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30
oC to 100
oC Continuous. This category may be available in the new MBA online store at
Bearings - Acetal - Single Row - with 302 Stainless Steel Balls.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30
oC to 100
oC Continuous. This category may be available in the new MBA online store at
Bearings - Acetal - Single Row - with 316 Stainless Steel Balls.
Related Information:
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.
UNC - UNF - METRIC - 303 and 304 grades. Also known as booker rod.
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Related Information:
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at
Bearings - Thrust - Ball - Flat - Stainless Steel.
Related Information:
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Nylon Insert for Locking. NylocTM and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at
Nuts - Hexagonal - Nylon Insert - Stainless Steel.
Includes galvanised and stainless steel. Wide variety of uses for attaching pins and small parts.
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. This category may be available in the new MBA online store at
Bearings - Ball - 316 Stainless Steel - Double Row - Open.
Related Information:
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. This category may be available in the new MBA online store at
Bearings - Ball - 316 Stainless Steel - Single Row - Open.
Related Information:
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Nylon tipped socket cap screws in 18-8 Stainless Steel - similar to 316 stainless
Spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations.
Two part assembly includes a barrel and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. Handles are black plastic. 303 stainless steel plunger assembly and housing. Pull up force approx 2.2kg. Lockout style (indicated in tables) allows you to pull and rotate handle 1/4 turn to lock plunger in retracted position.
Related Information:
Spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations.
Two part assembly includes a barrel and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. Handles are black plastic. 303 stainless steel plunger assembly and housing. Pull up force approx 2.2kg. Lockout style (indicated in tables) allows you to pull and rotate handle 1/4 turn to lock plunger in retracted position.
Related Information:
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000
oC. This category may be available in the new MBA online store at
Balls - Stainless Steel - 304 Grade.
Related Information:
A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000
oC. This category may be available in the new MBA online store at
Balls - Stainless Steel - 316 Grade.
Related Information:
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. This category may be available in the new MBA online store at
Balls - Stainless Steel - 316L Grade.
Related Information:
Hardness: Rockwell C: 55-60. Includes 420 and 440C grades
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel. This category may be available in the new MBA online store at
Balls - Stainless Steel - 400 Grade.
Related Information:
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at
Balls - Checking - Stainless Steel.
Related Information:
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at
Balls - Checking - Stainless Steel - With Tapped Shank.
Related Information:
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at
Balls - Fixture - Stainless Steel.
Related Information:
Levelling adjusters. Steel and stainless steel socket internal threads. Use your own custom thread length.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.