Rod Ends Plastic Categories
Rod Ends - Plastic - Female
Thermoplastic Body / L280(R) Polymer Ball. Also known as Heim Joints
Dimensions not shown are available on request.
Rod Ends - Plastic - Male
Thermoplastic Body / L280(R) Polymer Ball. Also known as Heim Joints
Dimensions not shown are available on request.
You may also be interested in
Balls Plastic
Balls - Plastic - Bored
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
Related Information:
Clevis Joints
Joints - Clevis - Plastic
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
Bungs
Bungs and Caps - Reversible - Round
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges.
Related Information:
Allthread
Threaded Rod - Allthread - Plastic
UNC - UNF - METRIC - Nylon and PVC. Also known as booker rod.
Light Weight. Non Corrosive. Vibration Resistant.
Engineering and Hobby Rod
Rod - Round - Acetal
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
Related Information:
Kites
Tips - For Kite Rods
Plastic tips fit over outside of rods and tubes for kites and other uses.
Joiners and connectors suitable for rod and tubing as well as for kites.
Cross Blocks - Heavy Duty - Two Knobs
Used for connecting two round rods at 90o.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
Cross Blocks - Heavy Duty - Two Nuts
Used for connecting two round rods at 90o.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
Handles - Latching - 2-Point Locking Rod Kit
Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.
Cross Blocks - Heavy Duty - One Knob One Nut
Used for connecting two round rods at 90o.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
Rail Systems - Miniature Profile
Ideal for precision applications where mounting space is limited
Gothic arch grooves at raceway contacts enables slide to sustain loads & movement from any direction. Made from stainless steel or plastic for corrosion resistance. End caps have oil holes for easy relubrication.
Shafting - Ground - Hobby - Steel
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.
Related Information:
Balls - Plastic - Acetal
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.
Related Information:
Balls - Plastic - PVC
Polyvinyl chloride. PVC is a chemically stable material, which shows little change in molecular structure, and also exhibits little change in its mechanical strength.
Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. It is easily worked or machined and has good chemical and biological resistance. It is relatively hard and can be polished to a shine. Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. Heat Deflection Temperature 176 F / 80 C. Rockwell Hardness 115. Zero water absorption in 24 hours.
Related Information:
Gauges - Plastic Thickness
Fan blade style has 13 colour-coded thickness blades riveted together for on-site convenience.
Made from polyester and vinyl. Non-corrosive, non-conductive, non-sparking and non-marring.
Bearings - Ball - 316 Stainless Steel - Single Row - Sealed
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Shim - Plastic
Easy to cut - colour coded - plastic shim sheets. Precision thicknesses.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Made from sturdy polyester.
Related Information:
Chain - Roller - Plastic - Simplex
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm. Single row.
Snap together construction - no joining links required.
Related Information:
Universal Joints - Telescoping - Plastic - Brass Spider and Insert
Acetal plastic telescoping universal joints with nickle plated brass spiders and bore inserts
Bearings - Acetal - Solid - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to wide inner ring bearings for P, F, Fl type housings but solid plastic.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Gear Racks - Module 0.5 - Plastic
20o Pressure Angle. Acetal and Nylon
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.
Gears - Mitre - Module 0.5 - Plastic
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.
Related Information:
Gears - Mitre - Module 1 - Plastic
1:1 Ratio. 20o Pressure Angle - Acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.
Related Information:
Gears - Mitre - Module 2 - Plastic
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.
Related Information:
Gears - Mitre - Module 3 - Plastic
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.
Related Information:
Gears - Spur - Module 0.4 - Plastic
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
Gears - Spur - Module 0.5 - Plastic
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
Gears - Spur - Module 0.7 - Plastic
PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.
Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
Gears - Spur - Module 0.8 - Plastic
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
Gears - Spur - Module 1.25 - Plastic
PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. Acetal.
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
Gears - Spur - Module 1.5 - Plastic
PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
Gears - Spur - Module 1 - Plastic
PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
Gears - Bevel - Module 0.5 - Plastic
For 90o angle power transfer. Ratios exceeding 1 to 1. Acetal.
20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.
Related Information:
Gears - Spur - Module 0.4 - Plastic with Insert
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
Gears - Spur - Module 0.5 - Plastic with Insert
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
Gears - Spur - Module 0.8 - Plastic with Insert
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
Plastic Bearing Oliver Design - Xyratex Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Washers - Flat - Peek
Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic
Related Information:
Washers - Flat - PVC
Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic
Flat washers.
Related Information:
Sprockets - 3.12 x 1.47mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 3.12mm miniature plastic chain.
Related Information:
Sprockets - 3.75 x 1.6mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 3.75mm miniature plastic or stainless chain.
Related Information:
Sprockets - 6.35 x 2.8mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 6.35mm plastic or steel chain (25-1 ASA). American Standard 25-1 - 1/4 inch.
Related Information:
Sprockets - 9.53 x 4.7mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 9.53x4.7mm plastic or steel chain (35-1 ASA). American Standard 35-1 - 3/8 inch.
Related Information:
Sprockets - 9.53 x 5.7mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 9.53x5.7mm steel chain (06B BS). British Standard 06B - 3/8 inch. For easy ready selected sets of chain and sprockets please see the HES website.
Related Information:
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic
Load and speed capability depend on the bearing used. Use with steel or plastic bearing inserts for plastic housings.
Related Information:
Housings - Bearing - Flanged - 3 Bolt Bracket - Plastic
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
Related Information:
Gears - Bevel - 32 Diametrical Pitch - Plastic
For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.
20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.
Related Information:
Gears - Bevel - 48 Diametrical Pitch - Plastic
For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.
20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127061 products in 2368 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
