Shafting General Purpose
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
General purpose tool steel with good wear resistance, toughness and machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.
Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.
Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Chrome vanadium alloy with unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight. Heat treating by air, water or oil.
Related Information:
General purpose tool steel with good wear resistance, durability and machinability
Dimensionally stable chromium, tungsten and vanadium electric furnace toolsteel can be used for intricate work. Low 787 to 815 oC (1450-1500 F) hardening range makes it easy to harden. Fully spheroidised and annealed for uniform carbide size and easy machining. Each piece is individually wrapped and clearly marked with size, analysis and correct hardness and tempering information. Edge squareness 0.003 mm per mm. Finish is 0.0008mm (0.000032 inch).
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.
Unhardened silversteel shafting for general purposes. Not suitable for precision bearings until machined to correct tolerances and hardened.
Related Information:
For use with rail supports and open linear bearings
Straightness: 0.1 mm / mtr.
For use with rail supports and open linear bearings
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design.
Related Information:
Use with idler shafts and idler pulleys. Has 88.9mm travel through the use of the vertical slot. Head is drilled and tapped to accept 38.1mm diameter idler shaft (ordered separately).
Idler shaft and pulleys not included with tensioner.
Related Information:
Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).
Idler shaft and pulleys not included with tensioner. Shaft is mounted to the side at 90o and is anchored by set screws.
Related Information:
Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).
Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Shaft is located in the centre of the tensioner between the adjusting slots.
Related Information:
Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).
Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Adjusting slots are parallel to each other.
Related Information:
Small light weight geared motors used in toys and small solar applications
NOTE! These do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges.
Related Information:
For Drylin Bearings.
Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and less than 9.
Moulded from black phenolic resin.
Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results. 712 Type suit standard metric rod.
For general hobby applications. This rod is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Related Information:
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
Related Information:
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
Related Information:
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
Related Information:
Related Information:
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small A/F sizes may not be perfectly straight.
Thin and thick Aluminum strip and rectangular profiles
Small sizes may not be perfectly straight.
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Length +/- 2 percent.
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
Cold rolled and hot drawn hex bar to ASTM B348
Saw Cut Ends.
Cold rolled hex bar to ASTM B348
Saw Cut Ends.
Contains 20 inserts per kit along with a standard tap, drill bit and installation tool. Installation tool is not needed but will make multiple installations easier.
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Fairloctm Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
Related Information:
Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
Related Information:
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
Related Information:
Recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and Less than 9.
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance.
Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting.
Related Information:
Precision ground shafting.
Related Information:
Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 125482
products in 2754 categories including
ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.