Small Parts & Bearings - an MBA company

Rc Boats And Accessories Categories


Accessories - Hobby - Aircraft
Accessories - Hobby - Aircraft


Generic Parts. Specific model parts may also be found by typing the model number into the search box. Reinforced Tape, Masking Tape, Micro Gear Nose, Gear Mech Retracts, Retractable Wing Tailwheels, gas struts



Fuel - Accessories
Fuel - Accessories


Includes fuel tanks for World Model Aircraft



Accessories - Hobby - Body Clips
Accessories - Hobby - Body Clips


Large and small body clips. Fluoro or standard. Plastic coated or anodised. Range of colours. Bent and straight.

See also large selection of clips in R-Clips.


Accessories - Hobby - Car and Buggy
Accessories - Hobby - Car and Buggy


Generic Parts. Specific model parts may also be found by typing the model number into the search box. Fail safes, aerials, heat sinks, body clips, tune pipe, clutch bell, bump start, engine break stand, engine fans, antenna tubes and tire warmers.

Includes Kyosho pull starts.


Accessories - Hobby - Helicopter
Accessories - Hobby - Helicopter


Generic Parts. Specific model parts may also be found by typing the model number into the search box. Training Gear, Polished Tuned Muffler, Heli Pitch, Foam Stand



Accessories - Hobby - Dogbones
Accessories - Hobby - Dogbones


Dog bones for Remote Control Cars



Accessories - Hobby - Wheel Nuts Adaptors and Pins
Accessories - Hobby - Wheel Nuts Adaptors and Pins


Replacement Wheel Nuts, adaptors and pins for remote control cars



Batteries - Accessories
Batteries - Accessories


Miscellaneous battery accessories - Lipo safety charge sacks - Balancers - Leads - Battery Monitors - Etc


Related Information:


Heat Shrink
Heat Shrink


Red or black heat shrink.


Ballscrew - Thomson Saginaw - Accessories
Ballscrew - Thomson Saginaw - Accessories

Also see combined categories:
All Ball Screws

Wiper Kits and Flanges for Ball Nuts. Match all components within the Thomson Saginaw range only.



Linear Slide - Drylin - Accessories
Linear Slide - Drylin - Accessories

Also see combined categories:
All Linear Slides

Insensitive to dust and dirt.

Carriage blocks and half slide rail. Make your own custom sized assemblies. Replace blocks on carriage assemblies. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.

Related Information:


Castors - Brakes Only
Castors - Brakes Only




Castors - Wheel Only
Castors - Wheel Only




Dubro by description Dubro Parts
Dubro by description Dubro Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Dubro by part number Dubro Parts
Dubro by part number Dubro Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.




Ballscrew - Thomson Saginaw - Nut
Ballscrew - Thomson Saginaw - Nut

Also see combined categories:
All Ball Screws

Ball Nuts to Suit Thomson Saginaw ball screws. Match all components within the Thomson Saginaw range only.

All Right hand thread only.


Mounts - Universal - For Acme Thread and Ballscrews
Mounts - Universal - For Acme Thread and Ballscrews


Use grade 8 hex socket head cap screws for mounting.



Balsa Wood - Projects
Balsa Wood - Projects


Many to choose from including bi-plane, miners hut, mosque, church, settlers hut, insect, passenger liner, sailing ship, old out house, ancient ruin. Great for learning about balsa modeling.

Instructions included.


Books - Hobby - Mousetrap Vehicles
Books - Hobby - Mousetrap Vehicles

Also see combined categories:
All Books

Tips and tricks and how-to guides for Mousetrap powered cars and boats

Activities guide and plans.

Related Information:


Collectibles - US Millitary - Commemorative Medals
Collectibles - US Millitary - Commemorative Medals


Bronze double sided medals displaying emblem and motto on one side and aircraft or ship on the other.



Balls - Checking - Tungsten Carbide
Balls - Checking - Tungsten Carbide

Also see combined categories:
All Fixture and Checking Balls

RC 65-68

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Fixture - Tungsten Carbide
Balls - Fixture - Tungsten Carbide

Also see combined categories:
All Fixture and Checking Balls

RC 65-68

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Checking - Stainless Steel
Balls - Checking - Stainless Steel

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Fixture - Stainless Steel
Balls - Fixture - Stainless Steel

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Checking - Stainless Steel - With Tapped Shank
Balls - Checking - Stainless Steel - With Tapped Shank

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Washers - Flat - Hardened Steel
Washers - Flat - Hardened Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.


Related Information:


Balls - Steel - Bored
Balls - Steel - Bored

Also see combined categories:
All Metallic Balls - Bored

Bored steel balls as used in steel rod ends.

Hardness: 58-64 Rc. Material: SUJ-2.

Related Information:


Leadscrews - Imperial - Acme - Alloy Steel
Leadscrews - Imperial - Acme - Alloy Steel

Also see combined categories:
All Imperial Leadscrews

Acme Leadscrew Thread - Use with Acme Supernuts

Alloy steel heat treated to RC 56-60.

Related Information:


Pulleys - Timing - Idler
Pulleys - Timing - Idler

Also see combined categories:
All Idler Pulleys

Complete with Needle Roller Bearing.

Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.

Related Information:


Sprockets - Idler
Sprockets - Idler

Also see combined categories:
All Sprockets for Roller Chain

Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.

Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.

Related Information:


Ballscrew - Nook Series - Flanges
Ballscrew - Nook Series - Flanges


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


Ballscrew - Nook Series - Right Hand
Ballscrew - Nook Series - Right Hand


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

High quality alloy steel, induction hardened to RC 56-60. Protective black oxide finish. Lead accurate by at least 0.00083mm per mm.


Bearings - SDP - Needle Roller - Flange Mounted - Non Aligning
Bearings - SDP - Needle Roller - Flange Mounted - Non Aligning

Also see combined categories:
All Press In Bearings

Fitted with drawn cup needle bearing. -30 to 110 oC. Retainer : Carbon Stee black oxide finish. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer. Non aligning.

Related Information:


Balls - Tooling - One Piece - Construction - Steel
Balls - Tooling - One Piece - Construction - Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm.

Related Information:


Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit
Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit
Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


Balls - Tooling - One Piece - Standard - Steel - Press Fit
Balls - Tooling - One Piece - Standard - Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

1144 steel heat treated to 53-57 RC.

Related Information:


Balls - Tooling - One Piece - Standard - Steel - Slip Fit
Balls - Tooling - One Piece - Standard - Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

1144 steel heat treated to 53-57 RC.

Related Information:


Balls - Tooling - Two Piece - Standard - Steel - Press Fit
Balls - Tooling - Two Piece - Standard - Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

1144 steel heat treated to 53-57 RC. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Tooling - Two Piece - Standard - Steel - Slip Fit
Balls - Tooling - Two Piece - Standard - Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

1144 steel heat treated to 53-57 RC. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Tooling - One Piece - Construction - Stainless Steel
Balls - Tooling - One Piece - Construction - Stainless Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 440C Stainless Steel heat treated to 55-58 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm.

Related Information:


Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit
Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

440C Stainless Steel heat treated to 55-58 RC.

Related Information:


Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit
Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

440C Stainless Steel heat treated to 55-58 RC.

Related Information:


Spring Motors - RINO
Spring Motors - RINO

Also see combined categories:
All Spring Motors

301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.


Spring Motors - SDP
Spring Motors - SDP

Also see combined categories:
All Spring Motors

301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.


Pins - Clik - Carbon Steel
Pins - Clik - Carbon Steel

Also see combined categories:
All Clik Lynch Pins

Self locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Also known as a lynch pin.

Pin is made from carbon steel and heat treated to RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated.

Related Information:


Pins - Clik - Mild Steel
Pins - Clik - Mild Steel

Also see combined categories:
All Clik Lynch Pins

Self locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Also known as a lynch pin.

Pin is made from carbon steel and heat treated to RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated.

Related Information:


Balls - Tooling - One Piece - Shoulder - Steel - Press Fit
Balls - Tooling - One Piece - Shoulder - Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC.

Related Information:


Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit
Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124352 products in 2772 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124352 products in 2772 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.